DTC B1900/73 Short in Front Driver Side Pretensioner Squib Circuit |
DTC B1901/73 Open in Front Driver Side Pretensioner Squib Circuit |
DTC B1902/73 Short to GND in Front Driver Side Pretensioner Squib Circuit |
DTC B1903/73 Short to B+ in Front Driver Side Pretensioner Squib Circuit |
| DTC Code | Detection Condition | Trouble Area |
| B1900/73 | When one of following conditions is met:
|
|
| B1901/73 | When one of following conditions is met:
|
|
| B1902/73 | When one of following conditions is met:
|
|
| B1903/73 | When one of following conditions is met:
|
|

| 1.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connector is properly connected to the front seat outer belt LH.
Disconnect the connector from the front seat outer belt LH.
Check that the floor wire connector (on the front seat outer belt LH side) is not damaged.
|
| ||||
| OK | |
| 2.CHECK FRONT SEAT OUTER BELT LH (FRONT PRETENSIONER LH) |
![]() |
Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 3.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
Check that the connector is properly connected to the center airbag sensor assembly.
Disconnect the connector from the center airbag sensor assembly.
Check that the terminal of the connector is not damaged.
Check that the short spring for the floor wire connector with the activation prevention mechanism is not deformed or damaged.
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE (FRONT PRETENSIONER LH CIRCUIT) |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O9-1 (L+) - Body ground | Ignition switch ON | Below 1 V |
| O9-2 (L-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O9-1 (L+) - O9-2 (L-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O9-1 (L+) - O9-2 (L-) | Always | 1 MΩ or higher |
| O9-1 (L+) - Body ground | Always | 1 MΩ or higher |
| O9-2 (L-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 5.CHECK CENTER AIRBAG SENSOR |
![]() |
Restore the released activation prevention mechanism of connector B to the original condition.
Connect the connectors to the front seat outer belt LH and the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| OK | A |
| NG (w/ Cool Box) | B |
| NG (w/o Cool Box) | C |
|
| ||||
|
| ||||
| A | ||
| ||