Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) > Power Seat Position is not Memorized

for Preparation Click here


DESCRIPTION

When the seat memory SET switch and a seat memory switch (seat memory switch 1 or seat memory switch 2) are pressed simultaneously, the outer mirror control ECU commands the position control ECU and switch through CAN communication to record each position value.

WIRING DIAGRAM


B188602E01


INSPECTION PROCEDURE

1.CHECK DTC
  1. Use the intelligent tester to check if the CAN communication system is functioning normally (Click here).
    Result 
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK FRONT POWER SEAT CONTROL FUNCTION
  1. Check that each function of the power seat operates normally by using the front power seat switches.

    OK:
    Each function of power seat operates normally by using seat switches.



NG
GO TO PROBLEM SYMPTOMS TABLE (Click here)
OK


3.CHECK SEAT MEMORY SWITCH FUNCTION
  1. Perform a memory operation properly. Check that the buzzer sounds to indicate the completion of the memory operation.

    NOTICE:
    1. The seat position will not be recorded if the seat memory SET switch and 2 or more of the seat memory switches (for example, seat memory switch 1 and seat memory switch 2) are pressed simultaneously.
    2. If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.

    OK:
    Seat memory switch function operates normally.



NG
Go to step 4
OK

END 

4.READ VALUE USING INTELLIGENT TESTER (PARK/NEUTRAL POSITION SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / ECT / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    ECT 
    Tester Display
    Measurement Item/Display
    Normal Condition
    Diagnostic Note
    Shift SW Status (P Range)
    Park neutral position switch status / ON or OFF
    ON: Shift lever in P
    OFF: Shift lever not in P
    -

    OK:
    On the intelligent tester screen, each item changes between ON and OFF according to above chart.



NG
GO TO AUTOMATIC TRANSMISSION SYSTEM (PNP SWITCH CIRCUIT) (Click here)
OK


5.READ VALUE USING INTELLIGENT TESTER (SEAT MEMORY SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Driver Seat / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Driver Seat 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SET Switch
    Seat memory SET switch signal / ON or OFF
    ON: Seat memory SET switch on
    OFF: Seat memory SET switch off
    -
    M1 Switch
    Seat memory switch 1 signal / ON or OFF
    ON: Seat memory switch 1 on
    OFF: Seat memory switch 1 off
    -
    M2 Switch
    Seat memory switch 2 signal / ON or OFF
    ON: Seat memory switch 2 on
    OFF: Seat memory switch 2 off
    -

OK:
On the intelligent tester screen, each item changes between ON and OFF according to above chart.



NG
Go to step 6
OK

REPLACE FRONT POWER SEAT SWITCH LH (Click here)  

6.INSPECT SEAT MEMORY SWITCH


    B165791E02
  1. Remove the seat memory switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (MRY) - 4 (E)
    Seat memory SET switch pressed
    Below 1 Ω
    Seat memory SET switch not pressed
    10 kΩ or higher
    2 (M1) - 4 (E)
    Seat memory switch 1 pressed
    Below 1 Ω
    Seat memory switch 1 not pressed
    10 kΩ or higher
    3 (M2) - 4 (E)
    Seat memory switch 2 pressed
    Below 1 Ω
    Seat memory switch 2 not pressed
    10 kΩ or higher



NG
REPLACE SEAT MEMORY SWITCH (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU - SEAT MEMORY SWITCH)


    B188604E01
  1. Disconnect the M8 ECU connector.

  1. Disconnect the M6 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M8-7 (M2) - M6-3 (M2)
    Always
    Below 1 Ω
    M8-7 (M2) - Body ground
    Always
    10 kΩ or higher
    M8-8 (M1) - M6-2 (M1)
    Always
    Below 1 Ω
    M8-8 (M1) - Body ground
    Always
    10 kΩ or higher
    M8-9 (MM) - M6-1 (MRY)
    Always
    Below 1 Ω
    M8-9 (MM) - Body ground
    Always
    10 kΩ or higher
    M8-10 (MSWE) - M6-4 (E)
    Always
    Below 1 Ω
    M8-10 (MSWE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK OUTER MIRROR CONTROL ECU OPERATION
  1. After replacing the outer mirror control ECU, check that the front power seat control functions operate normally using the front seat switches and seat memory switch.

    OK:
    Front power seat control functions operate normally.



NG
REPLACE FRONT POWER SEAT SWITCH LH (Click here)
OK

REPLACE OUTER MIRROR CONTROL ECU (Click here)