Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Short to B+ in CAN Bus Line

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus line and +B when there is resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3.

Symptom
Trouble Area
There is resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of DLC3.
  1. Short to +B
  2. Combination meter ECU
  3. Main body ECU
  4. Skid control ECU
  5. Steering angle sensor
  6. Center airbag sensor
  7. Bus buffer ECU*1
  8. Air conditioning amplifier
  9. ECM
  10. Power steering ECU
  11. 4WD control ECU*2
  12. Suspension control ECU*3
  13. No. 1 junction connector
  14. No. 2 junction connector
  15. No. 4 junction connector*3
*1: w/ Bus Buffer ECU
*2: w/ 4WD
*3: w/ Air Suspension

WIRING DIAGRAM


E211081E03


E211082E02


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 BRANCH WIRE)


    E194173E20
  1. Disconnect the H115 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H19-6 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H19-14 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3.CONNECT CONNECTOR
  1. Reconnect the H115 No. 1 junction connector.


NEXT


4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE)


    E194173E20
  1. Disconnect the H110 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H19-6 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H19-14 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    DLC3



NG
Go to step 15
OK


5.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER)


    E211087E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H110-12 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    DLC3



NG
Go to step 11
OK


6.SYSTEM CHECK
  1. Check the vehicle specifications.
    Result 
    Result
    Proceed to
    w/ Bus Buffer ECU
    A
    w/o Bus Buffer ECU
    B



B
Go to step 8
A


7.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - BUS BUFFER ECU)


    E211087E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-5 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H110-16 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    DLC3



NG
Go to step 12
OK


8.SYSTEM CHECK
  1. Check the vehicle specifications.
    Result 
    Result
    Proceed to
    w/ 4WD
    A
    w/o 4WD
    B



B
Go to step 10
A


9.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - 4WD CONTROL ECU)


    E211087E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-2 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H110-13 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    DLC3



NG
Go to step 13
OK


10.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - ECM)


    E211087E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-3 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H110-14 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    DLC3



NG
Go to step 14
OK

REPAIR OR REPLACE NO. 2 JUNCTION CONNECTOR 

11.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER)


    E211087E01
  1. Disconnect the H24 air conditioning amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H110-12 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

12.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (BUS BUFFER ECU)


    E211087E02
  1. Disconnect the H66 bus buffer ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-5 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H110-16 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BUS BUFFER ECU (CAN+, CAN-)
OK

REPLACE BUS BUFFER ECU 

13.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (4WD CONTROL ECU)


    E211087E03
  1. Disconnect the A28 4WD control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-2 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H110-13 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD CONTROL ECU (CANH, CANL)
OK

REPLACE 4WD CONTROL ECU (Click here)  

14.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)


    E211087E04
  1. Disconnect the A27 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-3 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H110-14 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
OK

REPLACE ECM (Click here)  

15.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    E211087E05
  1. Disconnect the H115 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-5 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H115-16 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


16.CONNECT CONNECTOR
  1. Reconnect the H115 No. 1 junction connector.

  1. Reconnect the H110 No. 2 junction connector.


NEXT


17.SYSTEM CHECK
  1. Check the vehicle specifications.
    Result 
    Result
    Proceed to
    w/ Air Suspension
    A
    w/o Air Suspension
    B



B
Go to step 23
A


18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR SIDE)


    E194173E20
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H19-6 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H19-14 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    DLC3



NG
Go to step 22
OK


19.CONNECT CONNECTOR
  1. Reconnect the O41 No. 4 junction connector.


NEXT


20.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - SUSPENSION CONTROL ECU)


    E158733E10
  1. Disconnect the O42 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O42-6 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O42-12 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)
    *b
    Rear of the vehicle
    *c
    DLC3



NG
Go to step 29
OK


21.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ECU)


    E158733E11
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O41-7 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)
    *b
    Front of the vehicle
    *c
    DLC3



NG
Go to step 30
OK

REPAIR OR REPLACE NO. 4 JUNCTION CONNECTOR 

22.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)


    E211087E06
  1. Disconnect the H115 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-2 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H115-13 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    DLC3
    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 24
A

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR) 

23.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ECU)


    E211087E06
  1. Disconnect the H115 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-2 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H115-13 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    DLC3



NG
Go to step 30
OK


24.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - POWER STEERING ECU)


    E211087E07
  1. Disconnect the H115 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-7 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H115-18 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    DLC3



NG
Go to step 31
OK


25.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU)


    E211087E08
  1. Disconnect the H115 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-6 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H115-17 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    DLC3



NG
Go to step 32
OK


26.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)


    E211087E09
  1. Disconnect the H115 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-9 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H115-20 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    DLC3



NG
Go to step 33
OK


27.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)


    E211087E10
  1. Disconnect the H115 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-4 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H115-15 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    DLC3



NG
Go to step 34
OK


28.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR)


    E211087E11
  1. Disconnect the H115 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H115-12 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    DLC3



NG
Go to step 35
OK

REPAIR OR REPLACE NO. 1 JUNCTION CONNECTOR 

29.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SUSPENSION CONTROL ECU)


    E158733E10
  1. Disconnect the O18 suspension control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O42-6 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O42-12 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)
    *b
    Rear of the vehicle
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SUSPENSION CONTROL ECU (CANH, CANL)
OK

REPLACE SUSPENSION CONTROL ECU (Click here)  

30.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ECU)


    E158736E03
  1. Disconnect the H37 combination meter ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-33 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H37-34 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter ECU)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

31.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU)


    E211087E07
  1. Disconnect the H112 power steering ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-7 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H115-18 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU (CANH, CANL)
OK

REPLACE POWER STEERING ECU (Click here)  

32.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MAIN BODY ECU)


    E211087E08
  1. Disconnect the H2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-6 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H115-17 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE MAIN BODY ECU 

33.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU)


    E211087E09
  1. Disconnect the A19 skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-9 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H115-20 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY (Click here)  

34.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR)


    E211087E10
  1. Disconnect the H6 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-4 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H115-15 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE STEERING ANGLE SENSOR (Click here)  

35.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTER AIRBAG SENSOR)


    E211087E11
  1. Disconnect the H56 center airbag sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H115-12 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR (Click here)