Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

DTC    U1002    Lost Communication with Gateway Module

for Preparation Click here


DESCRIPTION

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open. (One side of the CANH [branch wire]/CANL [branch wire] of the ECU and/or sensor is open.)

DTC Code
DTC Detection Condition
Trouble Area
U1002
Main body ECU cannot receive signals from all ECUs that have been memorized as those connected to the CAN MS bus.
  1. MS bus circuit
  2. Power seat control ECU branch wire or connector
  3. Multiplex tilt and telescopic ECU branch wire or connector
  4. Outer mirror control ECU branch wire or connector
  5. Power back door ECU branch wire or connector*
  6. Combination meter ECU main wire or connector
  7. Main body ECU main wire or connector
  8. Power seat control ECU
  9. Multiplex tilt and telescopic ECU
  10. Outer mirror control ECU
  11. Combination meter ECU
  12. Main body ECU
  13. Power back door ECU*
  14. No. 3 junction connector
  15. No. 4 junction connector*
*: w/ Power Back Door

WIRING DIAGRAM


C211085E01


C211086E01


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any other switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2.CHECK CONNECTOR
  1. Check the type of No. 3 junction connector.
    Result 
    Result
    Proceed to
    for 2-pin Connector
    A
    for 22-pin Connector
    B



B
Go to step 47
A


3.CHECK CAN BUS WIRE (MAIN WIRE FOR DISCONNECTION, BUS LINES FOR SHORT CIRCUIT)


    C191512E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Resistance of Malfunction
    H37-22 (CANH) - H37-21 (CANL)
    Ignition switch off
    54 to 69 Ω
    Below 53 Ω: Short in line
    70 Ω or higher: Open in CAN main bus line
    H37-22 (CANH) - H37-18 (B)
    Ignition switch off
    6 kΩ higher
    Below 6 kΩ: +B short
    H37-21 (CANL) - H37-18 (B)
    H37-22 (CANH) - H37-40 (E1)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short
    H37-21 (CANL) - H37-40 (E1)

    Result 
    Result
    Proceed to
    NG
    - Open in CAN main wire
    A
    NG (w/ Power Back Door)
    - Short in line
    - +B short
    - Ground short
    B
    NG (w/o Power Back Door)
    - Short in line
    - +B short
    - Ground short
    C
    OK
    D



B
Go to step 16

C
Go to step 27

D
Go to step 46
A


4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)


    C137766E78
  1. Disconnect the H104 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H104-1 (CANH) - H104-2 (CANL)
    Ignition switch off
    108 to 132 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/o Power Back Door)
    B
    NG (w/ Power Back Door)
    C



B
Go to step 9

C
Go to step 11
A


5.CONNECT CONNECTOR
  1. Reconnect the H104 No. 3 junction connector.


NEXT


6.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ECU)


    C137766E79
  1. Disconnect the H102 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H102-1 (CANH) - H102-2 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 7
OK

REPAIR OR REPLACE NO. 3 JUNCTION CONNECTOR 

7.CONNECT CONNECTOR
  1. Reconnect the H102 No. 3 junction connector.


NEXT


8.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ECU - NO. 3 JUNCTION CONNECTOR)


    C159487E17
  1. Disconnect the H37 combination meter ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-22 (CANH) - H37-21 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (COMBINATION METER ECU - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

9.CONNECT CONNECTOR
  1. Reconnect the H104 No. 3 junction connector.


NEXT


10.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU - NO. 3 JUNCTION CONNECTOR)


    C159597E03
  1. Disconnect the H2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-16 (CANP) - H2-15 (CANN)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (MAIN BODY ECU - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE MAIN BODY ECU 

11.CONNECT CONNECTOR
  1. Reconnect the H104 No. 3 junction connector.


NEXT


12.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)


    E158732E02
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-6 (CANH) - O41-12 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
OK


13.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - MAIN BODY ECU)


    E158732E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-5 (CANH) - O41-11 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 14
OK

REPAIR OR REPLACE NO. 4 JUNCTION CONNECTOR 

14.CONNECT CONNECTOR
  1. Reconnect the O41 No. 4 junction connector.


NEXT


15.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU - NO. 4 JUNCTION CONNECTOR)


    C159597E03
  1. Disconnect the H2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-16 (CANP) - H2-15 (CANN)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (MAIN BODY ECU - NO. 4 JUNCTION CONNECTOR)
OK

REPLACE MAIN BODY ECU 

16.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR SIDE)


    E158745E02
  1. Disconnect the H104 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-22 (CANH) - H37-21 (CANL)
    Ignition switch off
    108 to 132 Ω
    H37-22 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H37-21 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H37-22 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H37-21 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 26
OK


17.CONNECT CONNECTOR
  1. Reconnect the H104 No. 3 junction connector.


NEXT


18.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)


    E158733E01
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-6 (CANH) - O41-12 (CANL)
    Ignition switch off
    108 to 132 Ω
    O41-6 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O41-12 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O41-6 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O41-12 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
OK


19.CONNECT CONNECTOR
  1. Reconnect the O41 No. 4 junction connector.


NEXT


20.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - POWER BACK DOOR ECU)


    E158733E02
  1. Disconnect the O42 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O42-1 (CANH) - O42-7 (CANL)
    Ignition switch off
    200 Ω or higher
    O42-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O42-7 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O42-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O42-7 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 22
OK


21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - MAIN BODY ECU)


    E158733E03
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-5 (CANH) - O41-11 (CANL)
    Ignition switch off
    108 to 132 Ω
    O41-5 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O41-11 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O41-5 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O41-11 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 24
OK

REPAIR OR REPLACE NO. 4 JUNCTION CONNECTOR 

22.CONNECT CONNECTOR
  1. Reconnect the O42 No. 4 junction connector.


NEXT


23.CHECK FOR SHORT IN CAN BUS WIRES (POWER BACK DOOR ECU)


    E158746E01
  1. Disconnect the O30 power back door ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O30-6 (CANP) - O30-5 (CANN)
    Ignition switch off
    54 to 69 Ω
    O30-6 (CANP) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O30-5 (CANN) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O30-6 (CANP) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O30-5 (CANN) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER BACK DOOR ECU (NO. 4 JUNCTION CONNECTOR - POWER BACK DOOR ECU)
OK

REPLACE POWER BACK DOOR UNIT ASSEMBLY (Click here)  

24.CONNECT CONNECTOR
  1. Reconnect the O41 No. 4 junction connector.


NEXT


25.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)


    C159598E03
  1. Disconnect the H2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-16 (CANP) - H2-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    H2-16 (CANP) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H2-15 (CANN) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H2-16 (CANP) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H2-15 (CANN) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (NO. 4 JUNCTION CONNECTOR - MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU 

26.CONNECT CONNECTOR
  1. Reconnect the H104 No. 3 junction connector.


NEXT


27.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - POWER SEAT CONTROL ECU)


    C159607E13
  1. Disconnect the H97 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H97-1 (CANH) - H97-2 (CANL)
    Ignition switch off
    200 Ω or higher
    H97-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H97-2 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H97-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H97-2 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 36
OK


28.CONNECT CONNECTOR
  1. Reconnect the H97 No. 3 junction connector.


NEXT


29.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)


    C159607E14
  1. Disconnect the H96 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H96-1 (CANH) - H96-2 (CANL)
    Ignition switch off
    200 Ω or higher
    H96-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H96-2 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H96-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H96-2 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 38
OK


30.CONNECT CONNECTOR
  1. Reconnect the H96 No. 3 junction connector.


NEXT


31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU)


    C159608E32
  1. Disconnect the H98 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H98-1 (CANH) - H98-2 (CANL)
    Ignition switch off
    200 Ω or higher
    H98-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H98-2 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H98-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H98-2 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 40
OK


32.CONNECT CONNECTOR
  1. Reconnect the H98 No. 3 junction connector.


NEXT


33.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ECU)


    C159607E15
  1. Disconnect the H102 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H102-1 (CANH) - H102-2 (CANL)
    Ignition switch off
    108 to 132 Ω
    H102-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H102-2 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H102-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H102-2 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Result 
    Result
    Proceed to
    OK (w/o Power Back Door)
    A
    NG
    B
    OK (w/ Power Back Door)
    C



B
Go to step 42

C
REPAIR OR REPLACE NO. 3 JUNCTION CONNECTOR
A


34.CONNECT CONNECTOR
  1. Reconnect the H102 No. 3 junction connector.


NEXT


35.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)


    C159607E16
  1. Disconnect the H104 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H104-1 (CANH) - H104-2 (CANL)
    Ignition switch off
    108 to 132 Ω
    H104-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H104-2 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H104-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H104-2 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 44
OK

REPAIR OR REPLACE NO. 3 JUNCTION CONNECTOR 

36.CONNECT CONNECTOR
  1. Reconnect the H97 No. 3 junction connector.


NEXT


37.CHECK FOR SHORT IN CAN BUS WIRES (POWER SEAT CONTROL ECU)


    C159484E02
  1. Disconnect the X11 power seat control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    X11-5 (CANH) - X11-1 (CANL)
    Ignition switch off
    54 to 69 Ω
    X11-5 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    X11-1 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    X11-5 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    X11-1 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER SEAT CONTROL ECU (NO. 3 JUNCTION CONNECTOR - POWER SEAT CONTROL ECU)
OK

REPLACE FRONT POWER SEAT SWITCH LH (Click here)  

38.CONNECT CONNECTOR
  1. Reconnect the H96 No. 3 junction connector.


NEXT


39.CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU)


    C159591E02
  1. Disconnect the H57 multiplex tilt and telescopic ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H57-5 (CANH) - H57-14 (CANL)
    Ignition switch off
    54 to 69 Ω
    H57-5 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H57-14 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H57-5 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H57-14 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTIPLEX TILT AND TELESCOPIC ECU (NO. 3 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)  

40.CONNECT CONNECTOR
  1. Reconnect the H98 No. 3 junction connector.


NEXT


41.CHECK FOR SHORT IN CAN BUS WIRES (OUTER MIRROR CONTROL ECU)


    C158955E03
  1. Disconnect the M8 outer mirror control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    M8-1 (CAN) - M8-21 (CGND)
    Ignition switch off
    54 to 69 Ω
    M8-1 (CAN) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    M8-21 (CGND) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    M8-1 (CAN) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    M8-21 (CGND) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO OUTER MIRROR CONTROL ECU (NO. 3 JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU)
OK

REPLACE OUTER MIRROR CONTROL ECU (Click here)  

42.CONNECT CONNECTOR
  1. Reconnect the H102 No. 3 junction connector.


NEXT


43.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ECU)


    C158955E04
  1. Disconnect the H37 combination meter ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-22 (CANH) - H37-21 (CANL)
    Ignition switch off
    108 to 132 Ω
    H37-22 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H37-21 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H37-22 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H37-21 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ECU)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

44.CONNECT CONNECTOR
  1. Reconnect the H104 No. 3 junction connector.


NEXT


45.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)


    C159598E03
  1. Disconnect the H2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-16 (CANP) - H2-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    H2-16 (CANP) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H2-15 (CANN) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H2-16 (CANP) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H2-15 (CANN) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU 

46.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)


  1. Reconnect the cable to the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


    E146246E04

  1. Disconnect the DA, DB and DD main body ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DD-62 (GND1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    DA-1 (ALTB) - Body ground
    Always
    11 to 14 V
    DB-13 (BECU) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

47.CHECK CAN BUS WIRE (MAIN WIRE FOR DISCONNECTION, BUS LINES FOR SHORT CIRCUIT)


    C191512E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Resistance of Malfunction
    H37-22 (CANH) - H37-21 (CANL)
    Ignition switch off
    54 to 69 Ω
    Below 53 Ω: Short in line
    70 Ω or higher: Open in CAN main bus line
    H37-22 (CANH) - H37-18 (B)
    Ignition switch off
    6 kΩ higher
    Below 6 kΩ: +B short
    H37-21 (CANL) - H37-18 (B)
    H37-22 (CANH) - H37-40 (E1)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short
    H37-21 (CANL) - H37-40 (E1)

    Result 
    Result
    Proceed to
    NG
    - Open in CAN main wire
    A
    NG (w/ Power Back Door)
    - Short in line
    - +B short
    - Ground short
    B
    NG (w/o Power Back Door)
    - Short in line
    - +B short
    - Ground short
    C
    OK
    D



B
Go to step 59

C
Go to step 68

D
Go to step 83
A


48.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)


    C198236E69
  1. Disconnect the H111 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H111-4 (CANH) - H111-15 (CANL)
    Ignition switch off
    108 to 132 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/o Power Back Door)
    B
    NG (w/ Power Back Door)
    C



B
Go to step 52

C
Go to step 54
A


49.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ECU)


    C198236E72
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H111-1 (CANH) - H111-12 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 50
OK

REPAIR OR REPLACE NO. 3 JUNCTION CONNECTOR 

50.CONNECT CONNECTOR
  1. Reconnect the H111 No. 3 junction connector.


NEXT


51.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ECU - NO. 3 JUNCTION CONNECTOR)


    C159487E17
  1. Disconnect the H37 combination meter ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-22 (CANH) - H37-21 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (COMBINATION METER ECU - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

52.CONNECT CONNECTOR
  1. Reconnect the H111 No. 3 junction connector.


NEXT


53.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU - NO. 3 JUNCTION CONNECTOR)


    C159597E03
  1. Disconnect the H2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-16 (CANP) - H2-15 (CANN)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (MAIN BODY ECU - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE MAIN BODY ECU 

54.CONNECT CONNECTOR
  1. Reconnect the H111 No. 3 junction connector.


NEXT


55.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)


    E158732E02
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-6 (CANH) - O41-12 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
OK


56.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - MAIN BODY ECU)


    E158732E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-5 (CANH) - O41-11 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 57
OK

REPAIR OR REPLACE NO. 4 JUNCTION CONNECTOR 

57.CONNECT CONNECTOR
  1. Reconnect the O41 No. 4 junction connector.


NEXT


58.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU - NO. 4 JUNCTION CONNECTOR)


    C159597E03
  1. Disconnect the H2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-16 (CANP) - H2-15 (CANN)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (MAIN BODY ECU - NO. 4 JUNCTION CONNECTOR)
OK

REPLACE MAIN BODY ECU 

59.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR SIDE)


    E158745E02
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-22 (CANH) - H37-21 (CANL)
    Ignition switch off
    108 to 132 Ω
    H37-22 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H37-21 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H37-22 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H37-21 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 66
OK


60.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - POWER BACK DOOR ECU)


    E158733E02
  1. Disconnect the O42 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O42-1 (CANH) - O42-7 (CANL)
    Ignition switch off
    200 Ω or higher
    O42-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O42-7 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O42-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O42-7 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 62
OK


61.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - MAIN BODY ECU)


    E158733E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-5 (CANH) - O41-11 (CANL)
    Ignition switch off
    108 to 132 Ω
    O41-5 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O41-11 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O41-5 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O41-11 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 64
OK

REPAIR OR REPLACE NO. 4 JUNCTION CONNECTOR 

62.CONNECT CONNECTOR
  1. Reconnect the O42 No. 4 junction connector.


NEXT


63.CHECK FOR SHORT IN CAN BUS WIRES (POWER BACK DOOR ECU)


    E158746E01
  1. Disconnect the O30 power back door ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O30-6 (CANP) - O30-5 (CANN)
    Ignition switch off
    54 to 69 Ω
    O30-6 (CANP) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O30-5 (CANN) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O30-6 (CANP) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O30-5 (CANN) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER BACK DOOR ECU (NO. 4 JUNCTION CONNECTOR - POWER BACK DOOR ECU)
OK

REPLACE POWER BACK DOOR UNIT ASSEMBLY (Click here)  

64.CONNECT CONNECTOR
  1. Reconnect the O41 No. 4 junction connector.


NEXT


65.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)


    C159598E03
  1. Disconnect the H2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-16 (CANP) - H2-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    H2-16 (CANP) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H2-15 (CANN) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H2-16 (CANP) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H2-15 (CANN) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (NO. 4 JUNCTION CONNECTOR - MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU 

66.CONNECT CONNECTOR
  1. Reconnect the O41 No. 4 junction connector.


NEXT


67.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)


    C175162E47
  1. Disconnect the H111 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H111-4 (CANH) - H111-15 (CANL)
    Ignition switch off
    108 to 132 Ω
    H111-4 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H111-15 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H111-4 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H111-15 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
OK


68.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - POWER SEAT CONTROL ECU)


  1. w/o Power Back Door:



      C175162E48
    1. Disconnect the H111 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H111-3 (CANH) - H111-14 (CANL)
    Ignition switch off
    200 Ω or higher
    H111-3 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H111-14 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H111-3 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H111-14 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 73
OK


69.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)


    C175162E49
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H111-2 (CANH) - H111-13 (CANL)
    Ignition switch off
    200 Ω or higher
    H111-2 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H111-13 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H111-2 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H111-13 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 75
OK


70.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU)


    C175162E50
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H111-5 (CANH) - H111-16 (CANL)
    Ignition switch off
    200 Ω or higher
    H111-5 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H111-16 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H111-5 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H111-16 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 77
OK


71.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ECU)


    C175162E52
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H111-1 (CANH) - H111-12 (CANL)
    Ignition switch off
    108 to 132 Ω
    H111-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H111-12 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H111-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H111-12 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Result 
    Result
    Proceed to
    OK (w/o Power Back Door)
    A
    NG
    B
    OK (w/ Power Back Door)
    C



B
Go to step 79

C
REPAIR OR REPLACE NO. 3 JUNCTION CONNECTOR
A


72.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)


    C175162E54
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H111-4 (CANH) - H111-15 (CANL)
    Ignition switch off
    108 to 132 Ω
    H111-4 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H111-15 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H111-4 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H111-15 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 81
OK

REPAIR OR REPLACE NO. 3 JUNCTION CONNECTOR 

73.CONNECT CONNECTOR
  1. Reconnect the H111 No. 3 junction connector.


NEXT


74.CHECK FOR SHORT IN CAN BUS WIRES (POWER SEAT CONTROL ECU)


    C159484E02
  1. Disconnect the X11 power seat control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    X11-5 (CANH) - X11-1 (CANL)
    Ignition switch off
    54 to 69 Ω
    X11-5 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    X11-1 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    X11-5 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    X11-1 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER SEAT CONTROL ECU (NO. 3 JUNCTION CONNECTOR - POWER SEAT CONTROL ECU)
OK

REPLACE FRONT POWER SEAT SWITCH LH (Click here)  

75.CONNECT CONNECTOR
  1. Reconnect the H111 No. 3 junction connector.


NEXT


76.CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU)
C159591E02
  1. Disconnect the H57 multiplex tilt and telescopic ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H57-5 (CANH) - H57-14 (CANL)
    Ignition switch off
    54 to 69 Ω
    H57-5 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H57-14 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H57-5 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H57-14 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTIPLEX TILT AND TELESCOPIC ECU (NO. 3 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)  

77.CONNECT CONNECTOR
  1. Reconnect the H111 No. 3 junction connector.


NEXT


78.CHECK FOR SHORT IN CAN BUS WIRES (OUTER MIRROR CONTROL ECU)


    C158955E03
  1. Disconnect the M8 outer mirror control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    M8-1 (CAN) - M8-21 (CGND)
    Ignition switch off
    54 to 69 Ω
    M8-1 (CAN) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    M8-21 (CGND) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    M8-1 (CAN) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    M8-21 (CGND) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO OUTER MIRROR CONTROL ECU (NO. 3 JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU)
OK

REPLACE OUTER MIRROR CONTROL ECU (Click here)  

79.CONNECT CONNECTOR
  1. Reconnect the H111 No. 3 junction connector.


NEXT


80.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ECU)


    C158955E04
  1. Disconnect the H37 combination meter ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-22 (CANH) - H37-21 (CANL)
    Ignition switch off
    108 to 132 Ω
    H37-22 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H37-21 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H37-22 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H37-21 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ECU)
OK

REPLACE COMBINATION METER (Click here)  

81.CONNECT CONNECTOR
  1. Reconnect the H111 No. 3 junction connector.


NEXT


82.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)


    C159598E03
  1. Disconnect the H2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-16 (CANP) - H2-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    H2-16 (CANP) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H2-15 (CANN) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H2-16 (CANP) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H2-15 (CANN) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU 

83.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)


  1. Reconnect the cable to the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


    E146246E04

  1. Disconnect the DA, DB and DD main body ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DD-62 (GND1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    DA-1 (ALTB) - Body ground
    Always
    11 to 14 V
    DB-13 (BECU) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU