Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > Front Passenger Side Seat Belt Warning Light Malfunction

for Preparation Click here


DESCRIPTION

The meter ECU detects the state of the front seat inner belt RH when the front passenger side seat is occupied with the ignition switch to ON. If the front passenger side seat belt is not fastened, the front passenger side seat belt warning light on the integration control and panel blinks. If the seat belt is fastened, the warning light goes off.

WIRING DIAGRAM


B220008E01


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Check for DTCs.

    1. for CAN Communication System (Click here).

    2. for Airbag System (Click here).

    3. for Occupant Classification System (Click here).
      Result 
      Result
      Proceed to
      No output DTC
      A
      Output DTC (CAN communication)
      B
      Output DTC (Airbag system)
      C
      Output DTC (Occupant classification)
      D



B
GO TO CAN COMMUNICATION SYSTEM (Click here)

C
GO TO AIRBAG SYSTEM (Click here)

D
GO TO OCCUPANT CLASSIFICATION SYSTEM (Click here)
A


2.INSPECT FUSE (ECU-IG No. 1)


    B188612E03
  1. Remove the ECU-IG No. 1 fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU-IG No. 1 fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT PASSENGER SEAT BELT WARNING LIGHT)
  1. Operate the intelligent tester according to the steps on the display and select Active Test.

    Combination Meter 
    Item
    Test Part
    Control Range
    Diagnostic Note
    Front Passenger Side Seat Belt
    Front passenger side seat belt warning light
    Front passenger side seat belt warning light is on or off
    Confirm that the vehicle is stopped, engine idling

    OK:
    Passenger seat belt warning light condition can be switched by Active Test.



NG
Go to step 6
OK


4.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
  1. Temporarily replace the front seat inner belt RH with a new or normally functioning one (Click here).


NEXT


5.CHECK FRONT PASSENGER SIDE SEAT BELT WARNING LIGHT
  1. Check the front passenger side seat belt warning light function (Click here).

    OK:
    Front passenger side seat belt warning light operates normally.



NG
REPLACE COMBINATION METER (Click here)
OK

END (FRONT SEAT INNER BELT RH IS DEFECTIVE) 

6.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL - COMBINATION METER AND BATTERY)


    B167471E02
  1. Disconnect the H45 panel connector.

  1. Disconnect the H37 meter connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H45-14 (PBEW) - H37-15 (P/SB)
    Always
    Below 1 Ω
    H45-14 (PBEW) - Body ground
    Always
    10 kΩ or higher
    Standard Voltage 
    Tester Connection
    Switch Condition
    Specified Condition
    H45-16 (IG+) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY


    B165622E01
  1. Remove the integration control and panel (Click here).

  1. Apply battery voltage to the connector, and check that the front passenger side seat belt warning light comes on.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 16 (IG+)
    Battery negative (-) → Terminal 14(PBEW)
    Front passenger side seat belt warning light comes on



NG
REPLACE INTEGRATION CONTROL AND PANEL ASSEMBLY (Click here)
OK

REPLACE COMBINATION METER (Click here)