ENGINE ASSEMBLY > INSTALLATION |
| 1. REMOVE ENGINE STAND |
![]() |
Install the 2 engine hangers with the 2 bolts as shown in the illustration.
| Item | Part No. |
| Engine hanger | 12281-38030, 12281-38060 |
| Bolt | 90119-14120, 90119-A0166 |
Attach an engine sling device and hang the engine with a chain block.
Remove the bolts and engine assembly from the engine stand.
| 2. INSTALL ENGINE ASSEMBLY |
Slowly lower the engine assembly into the engine compartment.
Attach the engine mounting insulators to the vehicle.
![]() |
Install the 4 engine mounting insulator bolts.
Remove the 2 bolts and 2 engine hangers.
| 3. INSTALL OIL COOLER TUBE |
Install the oil cooler tube with the bolt.
| 4. INSTALL NO. 1 WATER BY-PASS PIPE |
![]() |
Connect the hose and install the water by-pass pipe with the 2 bolts.
| 5. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
![]() |
Using SST, hold the crankshaft.
Install the crankshaft angle sensor plate, drive gear and rear drive plate spacer to the crankshaft.
![]() |
Install and uniformly tighten 10 new bolts in the sequence shown in the illustration.
![]() |
Mark the top of each flywheel installation bolt with paint.
Tighten the flywheel installation bolts another 90° as shown in the illustration.
Check that the painted marks are now at a 90° angle to the top.
| 6. INSTALL EXHAUST MANIFOLD |
Install the exhaust manifold (Click here).
| 7. INSTALL GENERATOR ASSEMBLY |
Install the generator assembly (Click here).
| 8. INSTALL COOLER COMPRESSOR ASSEMBLY |
![]() |
Install the cooler compressor assembly with the 2 stud bolts.
Install the 2 bolts and 2 nuts.
Tighten the bolts and nuts in the order shown in the illustration to install the cooler compressor assembly.
| 9. INSTALL ENGINE WIRE |
![]() |
Connect the 2 connectors and 2 clips to the engine room junction block.
Install the engine wire with the nut, and then connect the 2 clips.
Install the ground wire with the bolt.
Connect the cable to the positive (+) battery terminal.
Install the wire to the positive (+) battery cable with the nut.
Install the ground wire with the bolt.
![]() |
Connect the 4 connectors to the connector holder block.
Connect the heater hoses.
| 10. INSTALL ECM |
![]() |
Connect the ECM connector and clamp.
| 11. CONNECT FUEL MAIN AND RETURN HOSE |
![]() |
Connect the fuel main and return hoses (Click here).
Install the fuel pipe clamp.
| 12. CONNECT PURGE LINE HOSE |
![]() |
Connect the purge line hose.
| 13. CONNECT VACUUM HOSE ASSEMBLY |
![]() |
Connect the union to check valve hose.
| 14. CONNECT OUTLET HEATER WATER HOSE C |
![]() |
Connect the outlet heater water hose C to the No. 1 water by-pass pipe, and slide the clamp to secure the hose.
| *a | RR |
| *b | LH |
| *c | 45° |
| 15. CONNECT INLET HEATER WATER HOSE C |
![]() |
Connect the inlet heater water hose C to the water by-pass pipe sub-assembly, and slide the clamp to secure the hose.
| *a | RR |
| *b | LH |
| *c | 45° |
| 16. INSTALL AIR CLEANER HOSE ASSEMBLY |
![]() |
Connect the air cleaner hose and tighten clamp.
Connect the No. 2 ventilation hose with the clamp.
Connect the vacuum hose.
| 17. INSTALL AIR CLEANER ASSEMBLY |
![]() |
Attach grommet to air cleaner before mounting the air cleaner.
Insert the air cleaner into the fender apron hole, and fully insert pin to grommet.
![]() |
Install the air cleaner with the 2 bolts.
Connect the connector and install the clamp and wire harness.
Connect the air cleaner hose and tighten the clamp.
| 18. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY |
for 4WD:
Install the transmission assembly (Click here).
for 2WD:
Install the transmission assembly (Click here).
| 19. INSTALL RADIATOR ASSEMBLY |
Install the radiator assembly (Click here).
| 20. ADD ENGINE OIL |
Add fresh oil.
| Oil Grade | Oil Viscosity (SAE) |
| API grade SL, SM or SN multigrade engine oil |
|
| API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil |
|
| Item | Specified Condition |
| Drain and refill without oil filter change | 7.1 liters (7.5 US qts, 6.2 Imp. qts) |
| Drain and refill with oil filter change | 7.5 liters (7.9 US qts, 6.6 Imp. qts) |
| Dry fill | 9.3 liters (9.8 US qts, 8.2 Imp. qts) |
Install the oil filler cap.
| 21. ADD ENGINE COOLANT |
Add engine coolant.
![]() |
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Install the reservoir cap.
Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.
Install the radiator cap.
Start the engine and warm it up until the thermostat opens.
Maintain the engine speed at 2000 to 2500 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines.
If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 23. INSPECT FOR OIL LEAK |
| 24. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 25. INSPECT FOR EXHAUST GAS LEAK |
| 26. INSPECT FOR FUEL LEAK |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester main switch ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.
| 27. INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY |
![]() |
Install the outer panel with the 7 bolts.
Connect the 2 washer hoses.
| 28. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY |
Install the windshield wiper motor (Click here).
| 29. INSTALL HOOD SUB-ASSEMBLY |
![]() |
Install the hood with the 4 bolts.
Attach the lower part of the 2 hood supports to the hood support bolt ball joints.
Attach the hood support clips.
| 30. ADJUST HOOD SUB-ASSEMBLY |
![]() |
Loosen the 4 hood side hinge bolts.
Move the hood to adjust the clearance to within the standard range.
Tighten the 4 hood side hinge bolts after the adjustment.
![]() |
Adjust the height of the hood front end by turning the cushion rubber.
Adjust the hood lock.
![]() |
Remove the hood lock nut cap.
![]() |
Loosen the 2 bolts and nut.
![]() |
Adjust the hood lock position so that the striker can enter it smoothly.
![]() |
Tighten the 2 bolts and nut after the adjustment.
| 31. INSPECT IGNITION TIMING |
Warm up and stop the engine.
Allow the engine to warm up to a normal operating temperature.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Start the engine and idle it.
Turn the intelligent tester main switch on.
Enter the following menus: Select: Powertrain / Engine and ECT / Data List / IGN Advance.
Disconnect the intelligent tester from the DLC3.
![]() |
When not using the intelligent tester:
Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
![]() |
Using the timing light, check the ignition timing.
Remove SST from the DLC3.
Check the ignition timing.
Disconnect the timing light from the engine.
| 32. INSPECT ENGINE IDLE SPEED |
Warm up and stop the engine.
Allow the engine to warm up to a normal operating temperature.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Race the engine at 2500 rpm for approximately 90 seconds.
Turn the intelligent tester main switch on.
Enter the following menus: Select: Powertrain / Engine and ECT / Data List / Engine Speed.
Disconnect the intelligent tester from the DLC3.
![]() |
When not using the intelligent tester:
Using SST, connect the tachometer probe to terminal 9 (TAC) of the DLC3.
Race the engine at 2500 rpm for approximately 90 seconds.
Check the idle speed.
Disconnect the tachometer from the DLC3.
| 33. INSPECT CO/HC |
Start the engine.
Keep the engine speed at 2500 rpm for approximately 180 seconds.
![]() |
Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idling.
Immediately check CO/HC concentration at idle and/or 2500 rpm.
If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.
Check the A/F sensor (Click here) and heated oxygen sensor (Click here) operation.
See the table below for possible causes, and then inspect and correct the applicable causes if necessary.
| CO | HC | Symptom | Cause |
| Normal | High | Rough idle |
|
| Low | High | Rough idle (Fluctuating HC reading) |
|
| High | High | Rough idle (Black smoke from exhaust) |
|
| 34. INSPECT ENGINE OIL LEVEL |
Warm up the engine, and then stop the engine and wait for 5 minutes.
Check that the engine oil level is between the low level and full level marks on the dipstick.
If low, check for leakage and add oil up to the full level mark.
| 35. INSPECT ENGINE COOLANT LEVEL |
![]() |
Check that the engine coolant level is between the LOW and FULL lines when the engine is cold.
If the engine coolant is low, check for leaks and add "TOYOTA Super Long Life Coolant" or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology to the FULL line.
| 36. INSPECT SRS WARNING LIGHT |