Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Suspension Control ECU Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
Suspension Control ECU Communication Stop Mode
When either condition below is met:
  1. Air suspension is not displayed on "CAN Bus Check".
  2. Applies to "Suspension Control ECU Communication Stop Mode" in "DTC Combination Table".
  1. Power source or inside suspension control ECU
  2. Suspension control ECU branch wire or connector
  3. Suspension control ECU
w/ Air Suspension

WIRING DIAGRAM


E158748E03


E158749E03


INSPECTION PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2.CHECK FOR OPEN IN CAN BUS WIRE (SUSPENSION CONTROL ECU BRANCH WIRE)


    E158728E01
  1. w/ AVS:

    1. Disconnect the O18 suspension control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      O18-30 (CANH) - O18-29 (CANL)
      Ignition switch off
      54 to 69 Ω



    E158729E01
  1. w/o AVS:

    1. Disconnect the O19 suspension control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      O19-29 (CANH) - O19-28 (CANL)
      Ignition switch off
      54 to 69 Ω



NG
REPAIR OR REPLACE SUSPENSION CONTROL ECU BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


3.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - BATTERY AND BODY GROUND)


    E158730E01
  1. w/ AVS:

    1. Reconnect the cable to the negative (-) battery terminal.

    2. Disconnect the O17 and O18 suspension control ECU connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O17-5 (GND) - Body ground
      Always
      Below 1 Ω
      O18-1 (GND) - Body ground

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      O17-6 (B) - Body ground
      Always
      11 to 14 V
      O18-10 (IG) - Body ground
      Ignition switch ON
      11 to 14 V



    E158729E02
  1. w/o AVS:

    1. Reconnect the cable to the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    2. Disconnect the O19 suspension control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O19-22 (GND) - Body ground
      Always
      Below 1 Ω

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      O19-24 (B) - Body ground
      Always
      11 to 14 V
      O19-10 (IG) - Body ground
      Ignition switch ON
      11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SUSPENSION CONTROL ECU (Click here)