Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › AIR FUEL RATIO SENSOR
RM27L0U _51 Engine / Hybrid System _049293 3UR-FBE ENGINE CONTROL _0235527 AIR FUEL RATIO SENSOR A

3UR-FBE ENGINE CONTROL  AIR FUEL RATIO SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 89467B 1.INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

a.
A194685

Install the air fuel ratio sensor to the front No. 2 exhaust pipe assembly by hand.


b.
A194686E06
2.552,1.083 2.948,1.458 2.948,1.458 2.948,1.625 false 0.792,1.573 1.875,1.781 1.083,0.208 10 false Fulcrum Length 2.813,1.635 3.198,1.844 0.385,0.208 10 false SST

Using SST, tighten the air fuel ratio sensor.

SST
09224-00010  

Torque:
without SST : 44 N*m (449 kgf*cm, 32 ft.*lbf)
with SST : 40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Make sure SST and the wrench are connected in a straight line.

·

Perform "Inspection After Repairs" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




Hide 89467B 2.INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

a.
A194685

Install the air fuel ratio sensor to the front exhaust pipe assembly by hand.


b.
A194686E06
2.552,1.083 2.948,1.458 2.948,1.458 2.948,1.625 false 0.792,1.573 1.875,1.781 1.083,0.208 10 false Fulcrum Length 2.813,1.635 3.198,1.844 0.385,0.208 10 false SST

Using SST, tighten the air fuel ratio sensor.

SST
09224-00010  

Torque:
without SST : 44 N*m (449 kgf*cm, 32 ft.*lbf)
with SST : 40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Make sure SST and the wrench are connected in a straight line.

·

Perform "Inspection After Repairs" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




Hide 17450B 4.INSTALL FRONT NO. 2 EXHAUST PIPE SUB-ASSEMBLY

A184985

a.

Install a new gasket and the front No. 2 exhaust pipe sub-assembly to the exhaust manifold LH with 3 new nuts.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


b.

Install a new gasket and the front No. 2 exhaust pipe assembly to the front No. 3 exhaust pipe sub-assembly with the 2 bolts and 2 new nuts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


c.

Connect the air fuel ratio sensor connector.


d.

Connect the heated oxygen sensor connector and 2 clamps.