17104
1.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH
Install a new gasket to the cylinder head and a new gasket to the No. 2 air tube.
Install the exhaust manifold gasket with the gasket tab facing toward the front of the engine.
Install the air tube gasket with the gasket's claws facing the tube side.
Temporarily install the exhaust manifold with the 2 nuts labeled A and 8 new nuts.
Uniformly tighten the nuts that are not labeled A, and then tighten the 2 nuts labeled A.
17167
2.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
Install the No. 1 exhaust manifold heat insulator with the 3 bolts.
17105
3.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH
Install a new gasket to the cylinder head and a new gasket to the No. 3 air tube.
Install the exhaust manifold gasket with the gasket tab facing toward the rear of the engine.
Install the air tube gasket with the gasket's claws facing the tube side.
Temporarily install the exhaust manifold with the 2 nuts labeled A and 8 new nuts.
Uniformly tighten the nuts that are not labeled A, and then tighten the 2 nuts labeled A.
17168
4.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
Install the No. 2 exhaust manifold heat insulator with the 3 bolts.
45203
5.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY
Align the matchmarks and insert the No. 2 steering intermediate shaft sub-assembly into the intermediate shaft.
Align the matchmarks and insert the No. 2 steering intermediate shaft sub-assembly into the power steering gear.
Install the 2 bolts.
58156
6.INSTALL FRONT NO. 4 FLOOR HEAT INSULATOR
Install the front No. 4 floor heat insulator with the 4 bolts.
58155
7.INSTALL FRONT NO. 3 FLOOR HEAT INSULATOR
Install the front No. 3 floor heat insulator with the 4 bolts.
17410
8.INSTALL FRONT EXHAUST PIPE ASSEMBLY
Install a new gasket and the front exhaust pipe assembly to the exhaust manifold RH with 3 new nuts.
Install a new gasket and the front exhaust pipe assembly to the center exhaust pipe assembly with the 2 bolts.
Connect the air fuel ratio sensor connector.
Connect the heated oxygen sensor connector and 2 clamps.
17450B
9.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY
Install a new gasket and the front No. 2 exhaust pipe sub-assembly to the exhaust manifold LH with 3 new nuts.
Connect the front No. 3 exhaust pipe sub-assembly to the exhaust pipe support.
Install 2 new gaskets and the front No. 3 exhaust pipe sub-assembly with the 4 bolts and 2 new nuts.
Connect the air fuel ratio sensor connector.
Connect the heated oxygen sensor connector.
37140
10.INSTALL FRONT PROPELLER SHAFT ASSEMBLY
37117B
11.INSTALL PROPELLER SHAFT HEAT INSULATOR
11452
12.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
13.INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.
If an exhaust gas leak has been repaired, perform an inspection following the repair (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
53739A
14.INSTALL FRONT FENDER APRON SEAL REAR LH
Install the fender apron seal with the 5 clips.
53737B
15.INSTALL FRONT FENDER APRON SEAL LH
Install the fender apron seal with the 6 clips.
53736A
16.INSTALL FRONT FENDER APRON SEAL REAR RH
Install the fender apron seal with the 5 clips.
53736
17.INSTALL FRONT FENDER APRON SEAL RH
Install the fender apron seal with the 6 clips.
51441
18.INSTALL NO. 1 ENGINE UNDER COVER