Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049293 3UR-FBE ENGINE CONTROL _0235531 SFI SYSTEM J

3UR-FBE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

The fuel pump circuit consists of the ECM, fuel pump and fuel pump ECU (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump ECU. Based on the signal sent from the ECM, the fuel pump ECU adjusts the fuel pump operation speed between 3 settings.

WIRING DIAGRAM

A179936E04
0.938,0.271 1.031,0.417 0.094,0.146 10 false 1 1.323,0.271 1.417,0.417 0.094,0.146 10 false 2 0.25,0.844 0.344,0.99 0.094,0.146 10 false 1 0.635,0.844 0.729,0.99 0.094,0.146 10 false 2 3.302,0.271 3.396,0.417 0.094,0.146 10 false 1 2.531,0.271 2.625,0.417 0.094,0.146 10 false 2 3.302,0.844 3.396,0.99 0.094,0.146 10 false 3 2.531,0.844 2.625,0.99 0.094,0.146 10 false 5 2.281,0.833 2.375,0.979 0.094,0.146 10 false 3 1.521,0.833 1.615,0.979 0.094,0.146 10 false 5 2.281,1.26 2.375,1.406 0.094,0.146 10 false 1 1.521,1.26 1.615,1.406 0.094,0.146 10 false 2 0.271,1.083 0.781,1.26 0.51,0.177 10 false F/PMP 1.042,0.521 1.365,0.698 0.323,0.177 10 false IGN 1.719,1.677 2.208,1.854 0.49,0.177 10 false F/PMP 2.74,1.281 3.25,1.458 0.51,0.177 10 false C/OPN 5.927,4.719 6.104,4.865 0.177,0.146 10 false 34 5.885,4.896 6.208,5.063 0.323,0.167 10 false A27 5.927,3.531 6.104,3.677 0.177,0.146 10 false 18 5.875,3.719 6.188,3.906 0.313,0.188 10 false A27 5.167,3.531 5.271,3.677 0.104,0.146 10 false 2 5.073,3.708 5.354,3.865 0.281,0.156 10 false O35 3.76,3.531 3.865,3.677 0.104,0.146 10 false 3 3.76,2.354 3.865,2.5 0.104,0.146 10 false 4 3.667,3.729 3.99,3.896 0.323,0.167 10 false O35 4.01,5.354 4.115,5.5 0.104,0.146 10 false 4 4.938,5.354 5.042,5.5 0.104,0.146 10 false 5 3.667,2.552 4.031,2.75 0.365,0.198 10 false O35 5.927,2.354 6.104,2.5 0.177,0.146 10 false 52 5.875,2.552 6.198,2.729 0.323,0.177 10 false A27 5.927,0.188 6.104,0.333 0.177,0.146 10 false 48 5.865,0.375 6.188,0.552 0.323,0.177 10 false A27 6.219,0.396 6.479,0.615 0.26,0.219 10 false FC 6.219,2.521 6.531,2.677 0.313,0.156 10 false FPC 6.219,3.698 6.417,3.854 0.198,0.156 10 false DI 4.708,2.521 5.021,2.677 0.313,0.156 10 false FPC 4.021,2.521 4.219,2.677 0.198,0.156 10 false +B 4.75,4.188 5.021,4.344 0.271,0.156 10 false FP- 4.052,4.188 4.26,4.344 0.208,0.156 10 false FP 4.844,3.708 5.021,3.865 0.177,0.156 10 false DI 4.021,3.708 4.146,3.865 0.125,0.156 10 false E 6.219,4.885 6.646,5.042 0.427,0.156 10 false MREL 6.49,5.563 6.823,5.719 0.333,0.156 10 false ECM 5.167,2.354 5.271,2.5 0.104,0.146 10 false 1 5.073,2.542 5.427,2.719 0.354,0.177 10 false O35 4.74,4.417 5.052,4.594 0.313,0.177 10 false O36 5.094,4.396 5.188,4.542 0.094,0.146 10 false 2 4,4.417 4.333,4.604 0.333,0.188 10 false O36 4.344,4.396 4.438,4.542 0.094,0.146 10 false 1 4.177,5.542 4.365,5.698 0.188,0.156 10 false B2 4.177,6.125 4.385,6.281 0.208,0.156 10 false Q1 4.177,6.271 4.875,6.448 0.698,0.177 10 false Fuel Pump 4.688,5.542 4.875,5.698 0.188,0.156 10 false E2 2.438,2.552 2.677,2.74 0.24,0.188 10 false 1B 2.24,2.552 2.333,2.708 0.094,0.156 10 false 4 2.854,2.552 3.104,2.75 0.25,0.198 10 false 1B 3.125,2.552 3.25,2.729 0.125,0.177 10 false 3 2.844,4.344 3.073,4.51 0.229,0.167 10 false 1B 3.146,4.323 3.24,4.479 0.094,0.156 10 false 2 1.531,3.042 1.781,3.198 0.25,0.156 10 false IG2 0.875,3.594 1.25,3.906 0.375,0.313 10 false IG2 MAIN 1.813,3.656 2.448,3.813 0.635,0.156 10 false EFI NO. 1 1.198,4.354 1.448,4.542 0.25,0.188 10 false 1B 1.01,4.323 1.104,4.479 0.094,0.156 10 false 6 0.688,4.344 0.906,4.51 0.219,0.167 10 false 1C 0.51,4.323 0.604,4.479 0.094,0.156 10 false 1 1.198,2.542 1.427,2.708 0.229,0.167 10 false 1B 1.01,2.552 1.104,2.708 0.094,0.156 10 false 7 0.688,2.552 0.948,2.74 0.26,0.188 10 false 1B 0.51,2.552 0.604,2.708 0.094,0.156 10 false 8 1.792,4.531 2.865,4.708 1.073,0.177 10 false Integration Relay 1.844,5.177 2.781,5.354 0.938,0.177 10 false Ignition Switch 1.844,5 2.146,5.177 0.302,0.177 10 false H10 1.333,4.625 1.427,4.781 0.094,0.156 10 false 6 1.333,5.563 1.427,5.719 0.094,0.156 10 false 5 1.354,4.844 1.604,5 0.25,0.156 10 false IG2 1.354,5.333 1.688,5.49 0.333,0.156 10 false AM2 1.354,5.917 1.688,6.073 0.333,0.156 10 false AM2 1.031,6.917 1.521,7.094 0.49,0.177 10 false Battery 1.938,2.938 2.313,3.25 0.375,0.313 10 false EFI MAIN 5.083,2.729 5.781,3.042 0.698,0.313 10 false Fuel Pump ECU

CAUTION / NOTICE / HINT

This troubleshooting procedure is based on the premise that the engine is started. If the engine is not started, proceed to the problem symptoms table (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (FUEL PUMP)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


d.

Check whether operating sounds can be heard while operating the relay using the Techstream.

OK:

Operating sounds can be heard from relay.




OK

2.INSPECT FUEL PUMP

NG

7.INSPECT CIRCUIT OPENING RELAY (C/OPN)
2.INSPECT FUEL PUMP
a.

Inspect the fuel pump (See page Engine / Hybrid System>3UR-FBE FUEL>FUEL PUMP>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the fuel pump (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

3.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)

NG

3.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)
a.

Disconnect the Q1 fuel pump connector.


b.

Disconnect the O36 fuel pump ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Q1-4 (B2) - O36-1 (FP) Always Below 1 Ω
Q1-5 (E2) - O36-2 (FP-) Always Below 1 Ω
Q1-4 (B2) or O36-1 (FP) - Body ground Always 10 kΩ or higher
Q1-5 (E2) or O36-2 (FP-) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM AND BODY GROUND)
a.

Disconnect the O35 fuel pump ECU connector.


b.

Disconnect the A27 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
O35-1 (FPC) - A27-52 (FPC) Always Below 1 Ω
O35-2 (DI) - A27-18 (DI) Always Below 1 Ω
O35-3 (E) - Body ground Always Below 1 Ω
O35-1 (FPC) or A27-52 (FPC) - Body ground Always 10 kΩ or more
O35-2 (DI) or A27-18 (DI) - Body ground Always 10 kΩ or more




OK

5.REPLACE FUEL PUMP ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE FUEL PUMP ECU
a.

Replace the fuel pump ECU (See page Engine / Hybrid System>3UR-FBE FUEL>FUEL PUMP ECU>REMOVAL).



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation.

OK:

Malfunction has been repaired successfully.




OK

END

NG

7.INSPECT CIRCUIT OPENING RELAY (C/OPN)
E145692E22
2.667,0.708 3.042,0.708 false 1.615,0.729 2,0.729 false 2.531,1.125 3.052,1.125 false 2.531,1.625 3.042,1.625 false 0.208,1.271 0.365,1.448 0.156,0.177 10 false 1 1.198,1.281 1.354,1.458 0.156,0.177 10 false 2 0.208,0.74 0.365,0.917 0.156,0.177 10 false 3 1.198,0.729 1.354,0.906 0.156,0.177 10 false 5 1.51,0.646 1.667,0.823 0.156,0.177 10 false 1 3.083,0.604 3.24,0.781 0.156,0.177 10 false 2 3.083,1.51 3.24,1.688 0.156,0.177 10 false 3 3.083,1.021 3.24,1.198 0.156,0.177 10 false 5

a.

Remove the circuit opening relay (C/OPN) from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
3 - 5 When no battery voltage applied to terminals 1 and 2 10 kΩ or higher
3 - 5 When battery voltage applied to terminals 1 and 2 Below 1 Ω




OK

8.INSPECT CIRCUIT OPENING RELAY (POWER SOURCE VOLTAGE)

NG

REPLACE CIRCUIT OPENING RELAY (C/OPN)

8.INSPECT CIRCUIT OPENING RELAY (POWER SOURCE VOLTAGE)
A162278E01
0.028,0 1.740,0.165 1.711,0.165 10 Engine Room Relay Block: 1.449,0.663 1.948,0.847 0.498,0.184 10 C/OPN

a.

Remove the circuit opening relay (C/OPN) from the engine room relay block.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
C/OPN relay (2) - Body ground Ignition switch ON 11 to 14 V
C/OPN relay (5) - Body ground Ignition switch ON 11 to 14 V




OK

9.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY - ECM AND FUEL PUMP ECU)

NG

15.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY - FUEL PUMP RELAY AND IGN FUSE)
9.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY - ECM AND FUEL PUMP ECU)
a.

Remove the circuit opening relay (C/OPN) from the engine room relay block.


b.

Disconnect the A27 ECM connector.


c.

Disconnect the O35 fuel pump ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C/OPN relay (1) - A27-48 (FC) Always Below 1 Ω
C/OPN relay (3) - O35-4 (+B) Always Below 1 Ω
C/OPN relay (1) or A27-48 (FC) - Body ground Always 10 kΩ or higher
C/OPN relay (3) or O35-4 (+B) - Body ground Always 10 kΩ or higher




OK

10.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)
a.

Disconnect the Q1 fuel pump connector.


b.

Disconnect the O36 fuel pump ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Q1-4 (B2) - O36-1 (FP) Always Below 1 Ω
Q1-5 (E2) - O36-2 (FP-) Always Below 1 Ω
Q1-4 (B2) or O36-1 (FP) - Body ground Always 10 kΩ or higher
Q1-5 (E2) or O36-2 (FP-) - Body ground Always 10 kΩ or higher




OK

11.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT FUEL PUMP
a.

Inspect the fuel pump (See page Engine / Hybrid System>3UR-FBE FUEL>FUEL PUMP>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the fuel pump (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

12.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM AND BODY GROUND)

NG

12.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM AND BODY GROUND)
a.

Disconnect the O35 fuel pump ECU connector.


b.

Disconnect the A27 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
O35-1 (FPC) - A27-52 (FPC) Always Below 1 Ω
O35-2 (DI) - A27-18 (DI) Always Below 1 Ω
O35-3 (E) - Body ground Always Below 1 Ω
O35-1 (FPC) or A27-52 (FPC) - Body ground Always 10 kΩ or more
O35-2 (DI) or A27-18 (DI) - Body ground Always 10 kΩ or more




OK

13.REPLACE FUEL PUMP ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE FUEL PUMP ECU
a.

Replace the fuel pump ECU (See page Engine / Hybrid System>3UR-FBE FUEL>FUEL PUMP ECU>REMOVAL).



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation.

OK:

Malfunction has been repaired successfully.




OK

END

NG

15.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY - FUEL PUMP RELAY AND IGN FUSE)
A380323E01
0.135,0.094 1.854,0.292 1.719,0.198 10 false Engine Room Relay Block: 1.583,0.927 2.063,1.146 0.479,0.219 10 false F/PMP 2.021,3.885 2.333,4.083 0.313,0.198 10 false IGN 0.917,4.125 1.396,4.344 0.479,0.219 10 false C/OPN

a.

Remove the circuit opening relay (C/OPN) from the engine room relay block.


b.

Remove the fuel pump relay (F/PMP) from the engine room relay block.


c.

Remove the IGN fuse from the engine room relay block.


d.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C/OPN relay (2) - IGN fuse (2) Always Below 1 Ω
C/OPN relay (5) - F/PMP relay (3) Always Below 1 Ω
C/OPN relay (2) or IGN fuse (2) - Body ground Always 10 kΩ or more
C/OPN relay (5) or F/PMP relay (3) - Body ground Always 10 kΩ or more




OK

16.INSPECT FUEL PUMP RELAY (F/PMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT FUEL PUMP RELAY (F/PMP)
E145692E22
2.667,0.708 3.042,0.708 false 1.615,0.729 2,0.729 false 2.531,1.125 3.052,1.125 false 2.531,1.625 3.042,1.625 false 0.208,1.271 0.365,1.448 0.156,0.177 10 false 1 1.198,1.281 1.354,1.458 0.156,0.177 10 false 2 0.208,0.74 0.365,0.917 0.156,0.177 10 false 3 1.198,0.729 1.354,0.906 0.156,0.177 10 false 5 1.51,0.646 1.667,0.823 0.156,0.177 10 false 1 3.083,0.604 3.24,0.781 0.156,0.177 10 false 2 3.083,1.51 3.24,1.688 0.156,0.177 10 false 3 3.083,1.021 3.24,1.198 0.156,0.177 10 false 5

a.

Remove the fuel pump relay (F/PMP) from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
3 - 5 When no battery voltage applied to terminals 1 and 2 10 kΩ or higher
3 - 5 When battery voltage applied to terminals 1 and 2 Below 1 Ω




OK

17.CHECK HARNESS AND CONNECTOR (FUEL PUMP RELAY - INTEGRATION RELAY, BATTERY AND BODY GROUND)

NG

REPLACE FUEL PUMP RELAY (F/PMP)

17.CHECK HARNESS AND CONNECTOR (FUEL PUMP RELAY - INTEGRATION RELAY, BATTERY AND BODY GROUND)
a.

Remove the F/PMP fuse from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
F/PMP fuse Always Below 1 Ω



c.

Reinstall the F/PMP fuse.


d.

Remove the fuel pump relay (F/PMP) from the engine room relay block.


e.

Remove the integration relay from the engine room relay block.


f.

Disconnect the 1B integration relay connector.


g.

Disconnect the cable from the battery positive (+) terminal.


h.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
F/PMP relay (1) - 1B-4 Always Below 1 Ω
F/PMP relay (5) - Positive (+) battery cable Always Below 1 Ω
F/PMP relay (2) - Body ground Always Below 1 Ω
F/PMP relay (1) or 1B-4 - Body ground Always 10 kΩ or higher
F/PMP relay (5) or Positive (+) battery cable - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR