Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049293 3UR-FBE ENGINE CONTROL _0235531 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P0120  Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction  P0121  Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  P0220  Throttle / Pedal Position Sensor / Switch "B" Circuit  P0222  Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input  P0223  Throttle / Pedal Position Sensor / Switch "B" Circuit High Input  P2135  Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation  


DESCRIPTION

The TP sensor is mounted on the throttle body, and detects the opening angle of the throttle valve. This sensor is a non-contact type. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds.

The TP sensor has 2 sensor circuits, each of which transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM.

As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air-fuel ratio correction, power increase correction and fuel-cut control.

U151636E03
4.396,1.51 4.646,1.052 4.646,1.052 4.74,1.052 false 0.833,1.573 0.885,2.198 true 1.25,1.104 0.927,1.906 true 0.885,2.938 1.365,3.563 true 0.865,2.583 0.479,3.125 true 5.719,0.531 5.885,0.531 5.885,0.531 6.146,1.854 true 5.531,2.25 5.896,2.552 false 5.521,2.344 5.521,2.156 false 3.875,1.656 4.188,1.813 0.313,0.156 10 false 4.65 4.573,1.917 4.948,2.083 0.375,0.167 10 false VTA2 4.969,2.708 5.344,2.875 0.375,0.167 10 false VTA1 3.823,2.26 4.198,2.417 0.375,0.156 10 false 2.60* 3.896,2.406 4.198,2.563 0.302,0.156 10 false 2.25 3.833,2.74 4.188,2.896 0.354,0.156 10 false 0.97* 3.896,2.885 4.198,3.042 0.302,0.156 10 false 0.69 3.958,1.417 4.188,1.573 0.229,0.156 10 false 5.0 4.792,0.99 5.771,1.146 0.979,0.156 10 false Fail-safe Angle 2.677,1.01 4.344,1.188 1.667,0.177 10 false Sensor Output Voltage (V) 6.479,3.406 6.833,3.563 0.354,0.156 10 false 86° 4.354,3.125 4.531,3.281 0.177,0.156 10 false 7° 4.167,3.417 4.427,3.573 0.26,0.156 10 false 0° 1.969,1.135 2.313,1.302 0.344,0.167 10 false ECM 1.302,1.75 1.719,1.906 0.417,0.156 10 false VCTA 1.302,2.75 1.646,2.906 0.344,0.156 10 false ETA 1.302,2.083 1.698,2.24 0.396,0.156 10 false VTA1 1.302,2.417 1.698,2.573 0.396,0.156 10 false VTA2 1.271,1.031 1.792,1.208 0.521,0.177 10 false Magnet 1.396,3.479 1.917,3.656 0.521,0.177 10 false Magnet 0.302,1.49 0.885,1.667 0.583,0.177 10 false IC No. 1 0.302,3.146 0.896,3.323 0.594,0.177 10 false IC No. 2 0.031,0.656 1.635,0.833 1.604,0.177 10 false Throttle Position Sensor 0.073,3.708 0.51,3.875 0.438,0.167 10 false Note: 0.073,4.021 3.396,4.365 3.323,0.344 10 false The throttle valve opening angle detected by the sensor terminal VTA1 is expressed as a percentage. 0.073,4.771 3.438,4.958 3.365,0.188 10 false Between 10% and 22%: Throttle valve fully closed 0.073,5.115 3.115,5.271 3.042,0.156 10 false Between 64% and 96%: Throttle valve fully open 0.073,5.438 2.792,5.594 2.719,0.156 10 false Approximately 19.4%: Fail-safe angle (7°) 4.031,0.448 5.719,0.635 1.688,0.188 10 false Line indicating VTA2 x 0.8 3.604,4.573 5.281,4.75 1.677,0.177 10 false Features of sensor output: 5.896,2.51 6.354,2.729 0.458,0.219 10 false 1.11 V 5.104,3.677 7.135,3.875 2.031,0.198 10 false Throttle Valve Opening Angle (°) 4.948,3.323 6.094,3.521 1.146,0.198 10 false Usable Range 4.646,4.083 6.24,4.281 1.594,0.198 10 false *: During fail-safe control 3.604,5.646 7.042,5.823 3.438,0.177 10 false (VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V) 3.604,4.938 7.104,5.271 3.5,0.333 10 false The difference in voltage between VTA1 and VTA2 x 0.8 is approximately 1.11 V.

DTC No. DTC Detection Condition Trouble Area
P0120 Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
·

Throttle Position (TP) sensor (built into throttle body assembly)

·

ECM


P0121 Difference between VTA1 and VTA2 voltages less than 0.8 V or more than 1.6 V for 2 seconds
(1 trip detection logic)
·

TP sensor (built into throttle body assembly)

·

TP sensor circuit

·

ECM


P0122 Output voltage of VTA1 0.2 V or less for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
·

TP sensor (built into throttle body assembly)

·

Short in VTA1 circuit

·

Open in VC circuit

·

ECM


P0123 Output voltage of VTA1 4.535 V or more for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
·

TP sensor (built into throttle body assembly)

·

Open in VTA1 circuit

·

Open in E2 circuit

·

Short between VC and VTA1 circuits

·

ECM


P0220 Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
·

TP sensor (built into throttle body assembly)

·

ECM


P0222 Output voltage of VTA2 1.75 V or less for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
·

TP sensor (built into throttle body assembly)

·

Short in VTA2 circuit

·

Open in VC circuit

·

ECM


P0223 Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
·

TP sensor (built into throttle body assembly)

·

Open in VTA2 circuit

·

Open in E2 circuit

·

Short between VC and VTA2 circuits

·

ECM


P2135 Either condition (a) or (b) met (1 trip detection logic):
(a) Difference between output voltages of VTA1 and VTA2 0.02 V or less for 0.5 seconds or more
(b) Output voltage of VTA1 0.2 V or less, and VTA2 1.75 V or less, for 0.4 seconds or more
·

Short between VTA1 and VTA2 circuits

·

TP sensor (built into throttle body assembly)

·

ECM



HINT:
·

When any of these DTCs are set, check the throttle valve opening angle by entering the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.


·

Throttle Position No. 1 is the VTA1 signal, and Throttle Position No. 2 is the VTA2 signal.

Reference (Normal Condition):
Display Item Accelerator Pedal Fully Released Accelerator Pedal Fully Depressed
Throttle Position No. 1 0.5 to 1.1 V 3.2 to 4.8 V
Throttle Position No. 2 2.1 to 3.1 V 4.6 to 5.0 V




MONITOR DESCRIPTION

P0120, P0122, P0123, P0220, P0222, P0223, P2135

The ECM uses the Throttle Position (TP) sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm the proper operation of the TP sensor.

·

A specific voltage difference is expected between the sensor terminals, VTA1 and VTA2, for each throttle valve opening angle. If the difference between VTA1 and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor, and stores a DTC.


·

VTA1 and VTA2 each have a specific voltage range. If VTA1 or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor, and stores a DTC.


·

VTA1 and VTA2 should never be close to the same voltage level. If VTA1 is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor, and stores a DTC.


If the malfunction is not repaired successfully, a DTC is set 10 seconds after the engine is next started.

P0121

This sensor transmits two signals: VTA1 and VTA2. VTA1 is used to detect the throttle opening angle and VTA2 is used to detect malfunctions in VTA1. The ECM performs several checks to confirm the proper operation of the TP sensor and VTA1.

For each throttle opening angle, a specific voltage difference is expected between the outputs of VTA1 and VTA2. If the output voltage difference between the two signals deviates from the normal operating range, the ECM interprets this as a malfunction of the TP sensor. The ECM illuminates the MIL and stores the DTC.

If the malfunction is not repaired successfully, the DTC is stores 2 seconds after the engine is next started.

MONITOR STRATEGY

Related DTCs P0120: Throttle position sensor 1 range check (Fluctuating)
P0121: Throttle position sensor rationality
P0122: Throttle position sensor 1 range check (Low voltage)
P0123: Throttle position sensor 1 range check (High voltage)
P0220: Throttle position sensor 2 range check (Fluctuating)
P0222: Throttle position sensor 2 range check (Low voltage)
P0223: Throttle position sensor 2 range check (High voltage)
P2135: Throttle position sensor range check (Correlation)
Required Sensors/Components (Main) Throttle position sensor
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration 2 seconds: P0120, P0122, P0123, P0220, P0222 and P0223
Within 2 seconds: P0121
0.5 seconds: P2135 Case 1
0.4 seconds: P2135 Case 2
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

P0120, P0122, P0123, P0220, P0222, P0223, P2135
Monitor runs whenever following DTCs are not present None
Either of following conditions A or B met -
A. Ignition switch ON 0.012 seconds or more
B. Electronic throttle actuator power ON

P0121
Monitor runs whenever following DTCs are not present None
Throttle position sensor circuit failure (P0120, P0122, P0123, P0220, P0222, P0223, P2135) Not detected
Either of following conditions met -
A. Ignition switch ON
B. Electronic throttle actuator power ON

TYPICAL MALFUNCTION THRESHOLDS

P0120:
VTA1 voltage 0.2 V or less, or 4.535 V or more

P0121
When either condition below is met: -
Difference of learned TP sensor opener position voltage between VTA2 and VTA1 More than 1.6 V
Difference of learned TP sensor opener position voltage between VTA2 and VTA1 Less than 0.8 V

P0122:
VTA1 voltage 0.2 V or less

P0123:
VTA1 voltage 4.535 V or more

P0220
When either condition below is met: Condition A or B
A. VTA2 voltage 1.75 V or less
B. VTA2 voltage when VTA1 0.2 V or more, and 2.02 V or less 4.8 V or more

P0222:
VTA2 voltage 1.75 V or less

P0223:
VTA2 voltage when VTA1 0.2 V or more, and 2.02 V or less 4.8 V or more

P2135 Case 1:
Difference between VTA1 and VTA2 voltages 0.02 V or less

P2135 Case 2:
VTA1 voltage 0.2 V or less
VTA2 voltage 1.75 V or less

COMPONENT OPERATING RANGE

VTA1 voltage 0.2 to 4.535 V
VTA2 voltage 1.75 to 4.8 V

CONFIRMATION DRIVING PATTERN

A380313E01
2.771,2.01 2.604,1.396 2.604,1.396 2.76,1.396 false 3.781,1.198 3.531,0.333 3.531,0.333 3.688,0.333 false 4.969,2.01 5.135,1.115 5.135,1.115 5.292,1.115 false 3.76,0.26 4.448,0.469 0.688,0.208 10 false Depressed 2.854,1.302 3.542,1.51 0.688,0.208 10 false Released 5.344,1.031 6.031,1.24 0.688,0.208 10 false Released 1.25,1.865 1.604,2.083 0.354,0.219 10 false Idling 0.458,2.156 1.656,2.365 1.198,0.208 10 false Ignition Switch ON 2.135,2.031 2.417,2.25 0.281,0.219 10 false [A] 3.792,1.802 4.073,2.021 0.281,0.219 10 false [B] 4.615,1.781 4.896,2 0.281,0.219 10 false [C] 5.01,3.01 5.292,3.229 0.281,0.219 10 false [D] 4.417,2.635 5.094,2.823 0.677,0.188 10 false 2 seconds

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine.

7.

With the vehicle stationary, fully depress and release the accelerator pedal [B].

8.

Idle the engine for 2 seconds or more [C].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

10.

Read the pending DTC.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0120, P0121, P0122, P0123, P0220, P0222, P0223 or P2135.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:

If the judgment result shows ABNORMAL, the system has a malfunction.


14.

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [D] again.

15.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




FAIL-SAFE

When any of these DTCs, as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A178644E01
0.127,2.78 0.330,2.945 0.202,0.165 10 D4 0.121,2.939 3.156,3.095 3.036,0.156 10 Throttle Position Sensor (Built into Throttle Body) 1.1,0.658 1.274,0.823 0.174,0.165 10 IC 1.1,1.547 1.274,1.712 0.174,0.165 10 IC 1.638,0.464 1.933,0.625 0.295,0.161 10 VTA 1.708,1.027 1.938,1.183 0.230,0.156 10 VC 1.558,1.572 1.946,1.755 0.387,0.184 10 VTA2 1.722,2.144 1.941,2.307 0.219,0.163 10 E2 5.583,0.466 5.962,0.627 0.379,0.161 10 VTA1 5.583,1.029 5.985,1.185 0.402,0.156 10 VCTA 5.583,1.574 5.971,1.758 0.387,0.184 10 VTA2 5.583,2.147 5.890,2.310 0.307,0.163 10 ETA 1.993,0.462 2.103,0.618 0.110,0.156 10 6 1.993,1.003 2.094,1.178 0.100,0.174 10 5 1.984,1.555 2.094,1.747 0.110,0.193 10 4 1.982,2.124 2.095,2.290 0.113,0.167 10 3 5.252,0.575 5.528,0.768 0.276,0.193 10 D56 5.252,1.126 5.528,1.319 0.276,0.193 10 D56 5.252,1.673 5.528,1.866 0.276,0.193 10 D56 5.252,2.252 5.528,2.445 0.276,0.193 10 D56 5.29,0.399 5.487,0.560 0.198,0.161 10 78 5.29,0.959 5.487,1.120 0.198,0.161 10 80 5.29,1.492 5.487,1.652 0.198,0.161 10 77 5.29,2.085 5.487,2.245 0.198,0.161 10 79 5.994,2.844 6.330,2.999 0.336,0.156 10 ECM

CAUTION / NOTICE / HINT

HINT:
·

These DTCs relate to the Throttle Position (TP) sensor.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING TECHSTREAM (THROTTLE POSITION)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / ETCS / Throttle Position No.1 and Throttle Position No.2.


d.

Check the values displayed on the Techstream.

Result
Throttle Position No. 1 (VTA1)
When Accelerator Pedal Released
Throttle Position No. 2 (VTA2)
When Accelerator Pedal Released
Throttle Position No. 1 (VTA1)
When Accelerator Pedal Depressed
Throttle Position No. 2 (VTA2)
When Accelerator Pedal Depressed
Trouble Area Proceed to
0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V VC circuit open A
4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V E2 circuit open A
0 to 0.2 V,
or 4.5 to 5.0 V
2.1 to 3.1 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 5.0 V
2.1 to 3.1 V
(Fail-safe)
VTA1 circuit open or ground short A
0.6 to 1.4 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 5.0 V
0.6 to 1.4 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 5.0 V
VTA2 circuit open or ground short A
0.5 to 1.1 V 2.1 to 3.1 V 3.2 to 4.8 V
(Not fail-safe)
4.6 to 5.0 V
(Not fail-safe)
TP sensor circuit normal B


HINT:
·

DTC P0121 is stored when the voltages output from VTA1 and VTA2 are not consistent with the characteristics of the sensors. Therefore, check the Freeze Frame Data when this DTC is output. Use the following formula to confirm relative fluctuations in voltage.

Features of sensor output:

VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V

VTA1: Throttle Position No. 1

VTA2: Throttle position No. 2


·

If DTC P0121 is output, proceed to "CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)".




A

2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)

B

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the D4 throttle body assembly connector.


b.

Disconnect the D56 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D4-5 (VC) - D56-80 (VCTA) Always Below 1 Ω
D4-6 (VTA) - D56-78 (VTA1) Always Below 1 Ω
D4-4 (VTA2) - D56-77 (VTA2) Always Below 1 Ω
D4-3 (E2) - D56-79 (ETA) Always Below 1 Ω
D4-5 (VC) or D56-80 (VCTA) - Body ground Always 10 kΩ or higher
D4-6 (VTA) or D56-78 (VTA1) - Body ground Always 10 kΩ or higher
D4-4 (VTA2) or D56-77 (VTA2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT ECM (VC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VC VOLTAGE)
U152961E01
0.045,0.01 2.384,0.361 2.338,0.351 10 Front view of wire harness connector: (to Throttle Body) 1.133,1.81 1.362,1.976 0.229,0.166 10 E2 2.153,1.81 2.382,1.976 0.229,0.166 10 VC 0.613,1.108 0.915,1.289 0.302,0.181 10 D4 1.304,1.783 1.622,1.401 false 2.222,1.805 1.969,1.396 false

a.

Disconnect the D4 throttle body assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
D4-5 (VC) - D4-3 (E2) Ignition switch ON 4.5 to 5.5 V




OK

4.REPLACE THROTTLE BODY ASSEMBLY

NG

4.REPLACE THROTTLE BODY ASSEMBLY
a.

Replace the throttle body assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>THROTTLE BODY>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the throttle body assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.



d.

Start the engine.


e.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read DTCs.

Result
Result Proceed to
P0120, P0121, P0122, P0123, P0220, P0222, P0223 and/or P2135 are output A
No DTC is output B



A

B

SYSTEM OK