Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049293 3UR-FBE ENGINE CONTROL _0235531 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P0300  Random / Multiple Cylinder Misfire Detected  P0301  Cylinder 1 Misfire Detected  P0302  Cylinder 2 Misfire Detected  P0303  Cylinder 3 Misfire Detected  P0304  Cylinder 4 Misfire Detected  P0305  Cylinder 5 Misfire Detected  P0306  Cylinder 6 Misfire Detected  P0307  Cylinder 7 Misfire Detected  P0308  Cylinder 8 Misfire Detected  


DESCRIPTION

A093767E16
2.302,0.906 2.708,1.073 0.406,0.167 10 false ECM 0.427,0.927 1.292,1.125 0.865,0.198 10 false CMP Sensor 0.427,1.729 1.292,1.917 0.865,0.188 10 false CKP Sensor

When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high HC concentration levels can cause increases in exhaust emission levels. High concentrations of HC can also cause increases in the Three-Way Catalytic Converter (TWC) temperature, which may cause damage to the TWC. To prevent these increases in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the TWC reaches the point of thermal degradation, the MIL blinks. To monitor misfires, the ECM uses both the Camshaft Position (CMP) sensor and the Crankshaft Position (CKP) sensor. The CMP sensor is used to identify any misfiring cylinders and the CKP sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted as when the crankshaft rotation speed variations exceed predetermined thresholds.

If the misfire rate exceeds the threshold level, the ECM illuminates the MIL and stores a DTC.

DTC No. DTC Detection Condition Trouble Area
P0300 Simultaneous misfiring of several cylinders occurs and one of the following conditions below is detected (2 trip detection logic):
·

Misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately).

·

Catalyst deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector

·

Fuel pressure

·

Mass Air Flow (MAF) meter

·

Engine Coolant Temperature (ECT) sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Air induction system

·

ECM

·

Fuel pressure switching valve

·

Fuel pressure regulator

·

Fuel pressure regulator for high pressure


P0301
P0302
P0303
P0304
P0305
P0306
P0307
P0308
Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection logic):
·

Misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately).

·

Catalyst deterioration misfire occurs (MIL illuminates).



When multiple DTCs for misfiring cylinders are set, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).

·

Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 10 to 50 misfires per 1000 crankshaft revolutions) occurs once.

·

An excessive misfiring rate (approximately 10 to 50 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.


The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause the Three-Way Catalytic Converter (TWC) damage, is detected:

·

At a high engine speed, a catalyst damage misfire, which monitored every 200 crankshaft revolutions, occurs once.

·

At a normal engine speed, a catalyst damage misfire, which monitored every 200 crankshaft revolutions, occurs 3 times.


HINT:

If a catalyst damage misfire occurs, the ECM informs the driver by flashing the MIL.


MONITOR STRATEGY

Related DTCs P0300: Multiple cylinder misfire
P0301: Cylinder 1 misfire
P0302: Cylinder 2 misfire
P0303: Cylinder 3 misfire
P0304: Cylinder 4 misfire
P0305: Cylinder 5 misfire
P0306: Cylinder 6 misfire
P0307: Cylinder 7 misfire
P0308: Cylinder 8 misfire
Required Sensors/Components (Main) Crankshaft position sensor and Camshaft position sensor
Required Sensors/Components (Related) Engine coolant temperature and intake air temperature sensors and Mass air flow meter
Frequency of Operation Continuous
Duration 1000 crankshaft revolutions (soon after engine is started: 1 time, other 4 times) (Emissions-related misfire)
200 crankshaft revolutions (1 or 3 times) (Catalyst-damaging misfire)
MIL Operation 2 driving cycles: MIL illuminates when misfire detect
MIL flashes immediately: When catalyst damaged misfire occur
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Misfire:
Monitor runs whenever following DTCs not stored P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0102, P0103 (Mass Air Flow Sensor)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0327, P0328, P0332, P0333, P032C, P032D, P033C, P033D (Knock Sensor)
P0335 (Crankshaft Position Sensor)
P1340 (Camshaft Position Sensor)
P0351 - P0358 (Igniter)
P0500 (Vehicle Speed Sensor)
P0705 (Shift Lever Position Switch)
Battery voltage 8 V or more
VVT system Not operated by scan tool
Engine speed 400 to 5900 rpm
Either of following conditions (a) or (b) met -
(a) ECT at engine start More than -7°C (19°F)
(b) ECT More than 20°C (68°F)
Fuel cut OFF

Monitor period of emission-related-misfire:
First 1000 revolutions after engine start, or Check Mode Crankshaft 1000 revolutions
Except above Crankshaft 1000 revolutions x 4

Monitor period of catalyst-damaged-misfire (MIL blinks):
All of following conditions 1, 2, 3 and 4 met Crankshaft 200 revolutions x 3
1. Driving cycles 1st
2. Check mode OFF
3. Engine speed Less than 2800 rpm
4. Engine load Below 80%
Except above Crankshaft 200 revolutions

TYPICAL MALFUNCTION THRESHOLDS

Monitor period of emission-related-misfire:
Misfire rate 1.5% or more

Monitor period of catalyst-damaged-misfire (MIL blinks):
Number of misfire per 200 revolutions 103 or more (varies with intake air amount and RPM)

MONITOR RESULT

WIRING DIAGRAM

A179943E06
4.76,0.344 5.031,0.49 0.271,0.146 10 false D56 4.76,1.031 5.031,1.177 0.271,0.146 10 false D56 4.76,1.719 5.031,1.885 0.271,0.167 10 false D56 4.76,2.417 5.031,2.563 0.271,0.146 10 false D56 4.76,3.104 5.031,3.25 0.271,0.146 10 false D56 4.76,3.792 5.031,3.938 0.271,0.146 10 false D56 4.76,4.49 5.031,4.635 0.271,0.146 10 false D56 4.76,5.219 5.031,5.365 0.271,0.146 10 false D56 4.76,5.833 5.031,5.979 0.271,0.146 10 false D56 4.771,6.177 5.042,6.323 0.271,0.146 10 false D56 5.896,6.479 6.24,6.625 0.344,0.146 10 false ECM 5.104,5.74 5.375,5.885 0.271,0.146 10 false E01 5.104,6.094 5.365,6.24 0.26,0.146 10 false E02 4.823,5.688 5,5.833 0.177,0.146 10 false 43 4.823,6.031 5,6.177 0.177,0.146 10 false 42 5.104,5.125 5.354,5.271 0.25,0.146 10 false #80 4.781,5.063 5.031,5.208 0.25,0.146 10 false 106 5.104,4.417 5.354,4.563 0.25,0.146 10 false #70 4.823,4.323 5,4.469 0.177,0.146 10 false 83 5.104,3.719 5.354,3.865 0.25,0.146 10 false #60 4.781,3.646 5.031,3.792 0.25,0.146 10 false 107 4.823,2.958 5,3.104 0.177,0.146 10 false 84 5.104,3.031 5.354,3.177 0.25,0.146 10 false #50 5.104,2.333 5.354,2.479 0.25,0.146 10 false #40 5.104,1.656 5.354,1.802 0.25,0.146 10 false #30 5.104,0.958 5.354,1.104 0.25,0.146 10 false #20 5.104,0.271 5.354,0.417 0.25,0.146 10 false #10 4.823,0.188 5,0.333 0.177,0.146 10 false 86 4.781,2.271 5.031,2.417 0.25,0.146 10 false 108 4.823,1.563 5,1.708 0.177,0.146 10 false 85 4.781,0.875 5.031,1.021 0.25,0.146 10 false 109 4.385,0.25 4.479,0.385 0.094,0.135 10 false 1 3.792,0.25 3.885,0.396 0.094,0.146 10 false 2 3.625,0.448 3.896,0.594 0.271,0.146 10 false d1 3.625,0.604 4.469,0.771 0.844,0.167 10 false No. 1 Injector 4.385,0.938 4.479,1.073 0.094,0.135 10 false 1 3.792,0.927 3.885,1.073 0.094,0.146 10 false 2 3.625,1.135 3.896,1.281 0.271,0.146 10 false c1 3.625,1.292 4.51,1.469 0.885,0.177 10 false No. 2 Injector 4.385,1.635 4.479,1.771 0.094,0.135 10 false 1 3.792,1.635 3.885,1.781 0.094,0.146 10 false 2 3.625,1.833 3.896,1.979 0.271,0.146 10 false d2 3.625,1.99 4.49,2.167 0.865,0.177 10 false No. 3 Injector 4.385,2.323 4.479,2.458 0.094,0.135 10 false 1 3.792,2.323 3.885,2.469 0.094,0.146 10 false 2 3.625,2.521 3.896,2.667 0.271,0.146 10 false c2 3.625,2.677 4.51,2.854 0.885,0.177 10 false No. 4 Injector 4.385,3.021 4.479,3.156 0.094,0.135 10 false 1 3.792,3.021 3.885,3.167 0.094,0.146 10 false 2 3.625,3.219 3.896,3.365 0.271,0.146 10 false d3 3.625,3.365 4.51,3.542 0.885,0.177 10 false No. 5 Injector 4.385,3.708 4.479,3.844 0.094,0.135 10 false 1 3.792,3.708 3.885,3.854 0.094,0.146 10 false 2 3.625,3.906 3.896,4.052 0.271,0.146 10 false c3 3.625,4.063 4.563,4.25 0.938,0.188 10 false No. 6 Injector 4.385,4.406 4.479,4.542 0.094,0.135 10 false 1 3.792,4.406 3.885,4.552 0.094,0.146 10 false 2 3.625,4.604 3.896,4.75 0.271,0.146 10 false d4 3.625,4.75 4.521,4.938 0.896,0.188 10 false No. 7 Injector 4.385,5.125 4.479,5.26 0.094,0.135 10 false 1 3.792,5.125 3.885,5.271 0.094,0.146 10 false 2 3.625,5.323 3.896,5.469 0.271,0.146 10 false c4 3.625,5.479 4.583,5.677 0.958,0.198 10 false No. 8 Injector 2.906,0.479 3.135,0.625 0.229,0.146 10 false INJ 2.333,0.344 2.51,0.49 0.177,0.146 10 false 1B 2.333,0.615 2.542,0.76 0.208,0.146 10 false 1B 2.385,0.188 2.479,0.333 0.094,0.146 10 false 8 2.385,0.781 2.479,0.917 0.094,0.135 10 false 7 1.542,0.927 1.792,1.083 0.25,0.156 10 false IG2 0.438,0.5 1.063,0.646 0.625,0.146 10 false IG2 MAIN 1.083,1.365 1.271,1.521 0.188,0.156 10 false 1B 0.26,1.365 0.479,1.531 0.219,0.167 10 false 1C 0.531,1.375 0.625,1.51 0.094,0.135 10 false 1 1.344,1.365 1.469,1.531 0.125,0.167 10 false 6 1.656,1.583 2.719,1.719 1.063,0.135 10 false Integration Relay 1.208,1.75 1.302,1.885 0.094,0.135 10 false 6 1.208,2.667 1.302,2.802 0.094,0.135 10 false 5 1.208,1.948 1.458,2.104 0.25,0.156 10 false IG2 1.208,2.438 1.521,2.583 0.313,0.146 10 false AM2 1.635,2.146 1.958,2.292 0.323,0.146 10 false H10 1.635,2.302 2.552,2.448 0.917,0.146 10 false Ignition Switch 1.25,3.24 1.563,3.385 0.313,0.146 10 false AM2 1.427,5.76 1.896,5.906 0.469,0.146 10 false Battery

A262511E06
5.365,0.844 5.698,1.01 0.333,0.167 10 false IGT1 3.458,0.906 3.792,1.073 0.333,0.167 10 false IGT1 5.365,2.51 5.698,2.677 0.333,0.167 10 false IGT3 5.365,4.177 5.698,4.344 0.333,0.167 10 false IGT5 5.365,5.844 5.698,6.01 0.333,0.167 10 false IGT7 5.365,1.24 5.698,1.406 0.333,0.167 10 false IGF1 3.458,1.323 3.792,1.49 0.333,0.167 10 false IGF1 5.021,5.948 5.313,6.104 0.292,0.156 10 false D56 5.021,4.281 5.313,4.438 0.292,0.156 10 false D56 5.021,2.625 5.313,2.781 0.292,0.156 10 false D56 5.031,1.344 5.323,1.5 0.292,0.156 10 false D56 5.031,0.948 5.323,1.104 0.292,0.156 10 false D56 5.083,0.76 5.271,0.917 0.188,0.156 10 false 40 5.083,2.427 5.271,2.583 0.188,0.156 10 false 37 5.083,4.094 5.271,4.25 0.188,0.156 10 false 35 5.083,5.76 5.271,5.917 0.188,0.156 10 false 38 5.042,1.167 5.313,1.323 0.271,0.156 10 false 104 5.938,6.615 6.302,6.802 0.365,0.188 10 false ECM 3.854,0.844 3.969,1 0.115,0.156 10 false 3 3.854,1.25 3.99,1.417 0.135,0.167 10 false 2 2.896,0.854 3,1.01 0.104,0.156 10 false 1 2.896,1.26 3.01,1.417 0.115,0.156 10 false 4 2.844,1.604 3.135,1.76 0.292,0.156 10 false D5 2.844,1.771 4.031,2 1.188,0.229 10 false No. 1 Ignition Coil 3.083,0.906 3.292,1.063 0.208,0.156 10 false +B 3.083,1.313 3.438,1.469 0.354,0.156 10 false GND 3.458,2.594 3.792,2.76 0.333,0.167 10 false IGT3 3.458,3 3.792,3.167 0.333,0.167 10 false IGF2 3.854,2.51 3.969,2.667 0.115,0.156 10 false 3 3.854,2.906 3.99,3.073 0.135,0.167 10 false 2 2.896,2.521 3,2.677 0.104,0.156 10 false 1 2.896,2.906 3.01,3.063 0.115,0.156 10 false 4 2.844,3.281 3.135,3.438 0.292,0.156 10 false D6 2.844,3.448 4,3.656 1.156,0.208 10 false No. 3 Ignition Coil 3.083,2.594 3.292,2.75 0.208,0.156 10 false +B 3.083,3 3.438,3.156 0.354,0.156 10 false GND 3.458,4.26 3.792,4.427 0.333,0.167 10 false IGT5 3.458,4.667 3.792,4.833 0.333,0.167 10 false IGF2 3.854,4.177 3.969,4.333 0.115,0.156 10 false 3 3.854,4.573 3.99,4.74 0.135,0.167 10 false 2 2.896,4.188 3,4.344 0.104,0.156 10 false 1 2.896,4.573 3.01,4.729 0.115,0.156 10 false 4 2.844,4.948 3.135,5.104 0.292,0.156 10 false D7 2.844,5.115 4.01,5.323 1.167,0.208 10 false No. 5 Ignition Coil 3.083,4.26 3.292,4.417 0.208,0.156 10 false +B 3.083,4.667 3.438,4.823 0.354,0.156 10 false GND 3.458,5.927 3.792,6.094 0.333,0.167 10 false IGT7 3.458,6.333 3.792,6.5 0.333,0.167 10 false IGF1 3.854,5.844 3.969,6 0.115,0.156 10 false 3 3.854,6.24 3.99,6.406 0.135,0.167 10 false 2 2.896,5.854 3,6.01 0.104,0.156 10 false 1 2.896,6.24 3.01,6.396 0.115,0.156 10 false 4 2.844,6.615 3.135,6.771 0.292,0.156 10 false D8 2.844,6.781 4.021,6.979 1.177,0.198 10 false No. 7 Ignition Coil 3.083,5.927 3.292,6.083 0.208,0.156 10 false +B 3.083,6.333 3.438,6.49 0.354,0.156 10 false GND 1.677,0.552 1.927,0.708 0.25,0.156 10 false INJ 0.167,0.156 1.146,0.344 0.979,0.188 10 false from IG2 Relay 1.542,7.552 1.667,7.719 0.125,0.167 10 false A 4.573,7.552 4.698,7.719 0.125,0.167 10 false B 4.813,7.552 4.938,7.719 0.125,0.167 10 false C

A262512E05
5.375,0.885 5.74,1.052 0.365,0.167 10 false IGT2 5.375,2.573 5.74,2.74 0.365,0.167 10 false IGT4 5.375,4.24 5.74,4.406 0.365,0.167 10 false IGT6 5.375,5.917 5.74,6.083 0.365,0.167 10 false IGT8 5.375,1.292 5.729,1.479 0.354,0.188 10 false IGF2 5.021,6.031 5.313,6.198 0.292,0.167 10 false D56 5.031,4.354 5.323,4.521 0.292,0.167 10 false D56 5.031,2.698 5.323,2.865 0.292,0.167 10 false D56 5.031,1.427 5.323,1.594 0.292,0.167 10 false D56 5.031,1.031 5.323,1.198 0.292,0.167 10 false D56 5.063,0.823 5.271,1 0.208,0.177 10 false 33 5.031,1.24 5.281,1.438 0.25,0.198 10 false 105 5.083,2.51 5.271,2.667 0.188,0.156 10 false 34 5.083,4.167 5.271,4.323 0.188,0.156 10 false 36 5.083,5.844 5.271,6 0.188,0.156 10 false 39 3.854,0.906 3.969,1.063 0.115,0.156 10 false 3 3.854,1.323 3.969,1.479 0.115,0.156 10 false 2 2.896,0.906 3,1.073 0.104,0.167 10 false 1 2.875,1.333 2.99,1.51 0.115,0.177 10 false 4 3.448,0.979 3.813,1.146 0.365,0.167 10 false IGT2 3.073,0.99 3.292,1.146 0.219,0.156 10 false +B 3.073,1.375 3.417,1.531 0.344,0.156 10 false GND 3.448,1.375 3.802,1.531 0.354,0.156 10 false IGF2 3.854,2.583 3.969,2.74 0.115,0.156 10 false 3 3.854,3 3.969,3.156 0.115,0.156 10 false 2 2.896,2.583 3,2.75 0.104,0.167 10 false 1 2.875,3 2.99,3.177 0.115,0.177 10 false 4 3.448,2.656 3.813,2.823 0.365,0.167 10 false IGT4 3.073,2.667 3.292,2.823 0.219,0.156 10 false +B 3.073,3.052 3.417,3.208 0.344,0.156 10 false GND 3.448,3.052 3.802,3.208 0.354,0.156 10 false IGF1 3.854,4.24 3.969,4.396 0.115,0.156 10 false 3 3.854,4.656 3.969,4.813 0.115,0.156 10 false 2 2.896,4.24 3,4.406 0.104,0.167 10 false 1 2.875,4.656 2.99,4.833 0.115,0.177 10 false 4 3.448,4.313 3.813,4.479 0.365,0.167 10 false IGT6 3.073,4.323 3.292,4.479 0.219,0.156 10 false +B 3.073,4.719 3.417,4.875 0.344,0.156 10 false GND 3.448,4.719 3.802,4.875 0.354,0.156 10 false IGF1 3.854,5.917 3.969,6.073 0.115,0.156 10 false 3 3.854,6.313 3.969,6.469 0.115,0.156 10 false 2 2.896,5.917 3,6.083 0.104,0.167 10 false 1 2.875,6.323 2.99,6.5 0.115,0.177 10 false 4 3.448,5.99 3.813,6.156 0.365,0.167 10 false IGT8 3.073,6 3.292,6.156 0.219,0.156 10 false +B 3.073,6.385 3.417,6.542 0.344,0.156 10 false GND 3.448,6.385 3.802,6.542 0.354,0.156 10 false IGF2 5.938,6.688 6.323,6.885 0.385,0.198 10 false ECM 1.542,0.083 1.677,0.25 0.135,0.167 10 false A 4.563,0.083 4.698,0.25 0.135,0.167 10 false B 4.802,0.083 4.938,0.25 0.135,0.167 10 false C 2.729,1.646 3.042,1.813 0.313,0.167 10 false D13 2.729,1.792 3.885,1.979 1.156,0.188 10 false No. 2 Ignition Coil 2.729,3.323 3.042,3.49 0.313,0.167 10 false D12 2.729,3.479 3.885,3.677 1.156,0.198 10 false No. 4 Ignition Coil 2.729,4.99 3.042,5.156 0.313,0.167 10 false D11 2.729,5.135 3.875,5.313 1.146,0.177 10 false No. 6 Ignition Coil 2.729,6.656 3.042,6.823 0.313,0.167 10 false D10 2.729,6.813 3.885,7 1.156,0.188 10 false No. 8 Ignition Coil

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the Techstream on.

4.

Record the DTC(s) and freeze frame data.

5.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

6.

Using the Techstream, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>CHECK MODE PROCEDURE).

7.

Read the misfire counts of each cylinder (Cylinder #1 Misfire Count to Cylinder #8 Misfire Count) with the engine idling.

8.

Drive the vehicle several times with the conditions, such as engine speed and engine load, shown in Misfire RPM and Misfire Load in the Data List.

HINT:

In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, using the Misfire RPM and Misfire Load in the Data List.

Engine speed Duration
Idling 8.0 minutes or more
1000 4.5 minutes or more
2000 2.5 minutes or more
3000 1.5 minute or more


9.

Check whether misfires have occurred by checking DTCs and freeze frame data.

HINT:

Do not turn the ignition switch off until the stored DTCs and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC, freeze frame data and other data will be erased.


10.

Record the DTC(s), freeze frame data and misfire counts.

11.

Turn the ignition switch off and wait for at least 15 seconds.

12.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.

·

FFVs update the alcohol concentration learned value (Alcohol Density Estimate) when the vehicle is refueled. As idling stability may decrease when fuels having different properties are used, check with the customer about the fuels recently used in the vehicle.

·

Make sure to compare the value of "Alcohol Density Estimate" in the freeze frame data with the current "Alcohol Density Estimate" value in the Data List.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the freeze frame data.

·

If the misfire still cannot be reproduced even though the conditions stored in the freeze frame data have been duplicated, one of the following factors is considered to be a possible cause of the problem:

1.

The fuel level is low.

2.

Improper fuel is used.

3.

The spark plugs are dirty.


·

After finishing repairs, check that no misfires occur in each cylinder (No. 1, No. 2, No. 3, No. 4, No. 5, No. 6, No. 7 and No. 8 cylinder).

·

Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern, after the repairs.

·

For 6 and 8 cylinder engines, the ECM intentionally does not store the specific misfiring cylinder DTCs at high engine speeds. If misfires only occur during high engine speed driving, only DTC P0300 is stored.

In the event of DTC P0300 being present, perform the following operations:

2.

Start the engine and conduct the confirmation driving pattern.

3.

Read the misfiring rates of each cylinder or DTC(s) using the Techstream.

4.

Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.

5.

After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P0300 is not stored.


·

With the alcohol concentration learned value, Long FT and Short FT in the freeze frame data, it is possible to determine the actual A/F deviation when a malfunction occurs.

·

When the Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfires occurred only while warming up the engine.

·

An extremely imbalanced drive wheel, which causes body vibration, may cause misfire DTCs detection.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 are output A
P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 and other DTCs are output B


HINT:

If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and P0308 are output, troubleshoot those DTCs first.



A

2.CHECK FREEZE FRAME DATA AND DATA LIST

B

2.CHECK FREEZE FRAME DATA AND DATA LIST
a.

Make a note of the freeze frame data "Short FT #1 or #2" and "Long FT #1 or #2" which were recorded the moment DTCs were stored.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the Techstream on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Short FT #1 or #2 and Long FT #1 or #2.


f.

Compare the air fuel ratio learned value (total of "Short FT #1" + "Long FT #1") in the freeze frame data with that in the Data List.

Result
Short FT + Long FT Proceed to
Freeze Frame Data Data List
-35% or less -35% or less A
Higher than -35% Higher than -35%
-35% or less Higher than -35% B

HINT:

If only the freeze frame data indicates -35% or less, a misfire may have occurred in the past. Confirm the driving conditions with the customer (if the customer drove the vehicle in a way that can cause misfire, such as driving a short distance with a cold engine repeatedly). If the cause of misfire is due to driving conditions, clear the DTCs, check that there are no other malfunctions, and return the vehicle to the customer.

Explain to the customer points to be careful about when driving a flexible fuel vehicle. (Refer to the owner's manual for details.)




A

3.CHECK PCV HOSE CONNECTIONS

B

END

3.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections.

OK:

PCV hose is connected correctly and is not damaged.




OK

4.READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)

NG

4.READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire / Misfire RPM and Misfire Load.


d.

Read and note the Misfire RPM and Misfire Load values.

HINT:

The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.




NEXT

5.READ VALUE USING TECHSTREAM (CATALYST OT MF F/C)
5.READ VALUE USING TECHSTREAM (CATALYST OT MF F/C)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst OT MF F/C.


d.

Read the value displayed on the Techstream.

Result
Data List Display Item Proceed to
Catalyst OT MF F/C Avail A
Not Avl B



A

6.PERFORM ACTIVE TEST USING TECHSTREAM (PROHIBIT THE CATALYST OT MISFIRE PREVENT F/C)

B

7.READ VALUE USING TECHSTREAM (CYLINDER MISFIRE COUNT)
6.PERFORM ACTIVE TEST USING TECHSTREAM (PROHIBIT THE CATALYST OT MISFIRE PREVENT F/C)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.



d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire prevent F/C.


e.

Perform the Active Test.

NOTICE:

When performing the Active Test, make sure the vehicle is stopped and either idling or being revved within 3000 rpm.




NEXT

7.READ VALUE USING TECHSTREAM (CYLINDER MISFIRE COUNT)
7.READ VALUE USING TECHSTREAM (CYLINDER MISFIRE COUNT)
a.

Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire / Cylinder #1 Misfire Count, #2, #3, #4, #5, #6, #7 and #8.


b.

Allow the engine to idle.


c.

Read each value for Cylinder #1 Misfire Count to Cylinder #8 Misfire Count displayed on the Techstream. If no misfire counts occur in any cylinders, perform the following procedures:

i.

Move the shift lever to the D position.


ii.

Check the Cylinder #1 Misfire Count to Cylinder #8 Misfire Count.


iii.

If misfire counts are still not displayed, perform procedure "A" and "B" and then check the misfire counts again.



d.

Drive the vehicle with the Misfire RPM and Misfire Load noted in the "READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)" procedures above. (Procedure "A")


e.

Read the Cylinder #1 Misfire Count to Cylinder #8 Misfire Count or DTCs displayed on the Techstream. (Procedure "B")

Result
Misfire Count Proceed to
Most misfires occur in only 1 or 2 cylinders A
3 cylinders or more have equal misfire counts B

HINT:
·

If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.

·

If the freeze frame data's record of the ECT is below 75°C (167°F), the misfire may be detected only when the engine is cold.

·

If the freeze frame data's record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.





A

8.INSPECT SPARK PLUG

B

18.CHECK AIR INDUCTION SYSTEM
8.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the spark plug (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

9.CHECK FOR SPARK (SPARK TEST)

NG

9.CHECK FOR SPARK (SPARK TEST)
a.

Perform a spark test (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:

If the result of the spark test is normal, proceed to the next step.




NEXT

10.CHECK CYLINDER COMPRESSION PRESSURE
10.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>3UR-FBE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

11.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50, #60, #70 AND/OR #80 VOLTAGE)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

11.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50, #60, #70 AND/OR #80 VOLTAGE)
U152965E01
0.15,0.993 0.445,1.163 0.295,0.170 10 D56 0.068,0.039 2.416,0.395 2.348,0.356 10 Front view of wire harness connector: (to ECM) 1.883,0.965 2.169,1.120 0.286,0.156 10 E01 3.056,2.533 3.323,2.688 0.267,0.156 10 #10 3.02,1.054 3.287,1.210 0.267,0.156 10 #30 2.48,0.986 2.747,1.142 0.267,0.156 10 #50 2.14,2.895 2.410,3.051 0.271,0.156 10 #60 2.39,2.648 2.675,2.804 0.286,0.156 10 #40 2.785,2.795 3.042,2.951 0.258,0.156 10 #20 3.159,2.51 2.537,1.971 false 2.636,1.158 2.342,1.977 false 3.135,1.231 2.445,1.977 false 2.239,1.725 2.033,1.146 false 2.538,2.098 2.893,2.786 false 2.445,2.098 2.554,2.64 false 2.263,2.889 2.343,2.109 false 1.839,2.655 2.106,2.811 0.267,0.156 10 #80 2.004,2.65 2.235,2.109 false 1.44,2.9 1.707,3.056 0.267,0.156 10 #70 1.625,2.885 2.249,1.952 false

a.

Disconnect the D56 ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
D56-86 (#10) - D56-43 (E01) Ignition switch ON 11 to 14 V
D56-109 (#20) - D56-43 (E01) Ignition switch ON 11 to 14 V
D56-85 (#30) - D56-43 (E01) Ignition switch ON 11 to 14 V
D56-108 (#40) - D56-43 (E01) Ignition switch ON 11 to 14 V
D56-84 (#50) - D56-43 (E01) Ignition switch ON 11 to 14 V
D56-107 (#60) - D56-43 (E01) Ignition switch ON 11 to 14 V
D56-83 (#70) - D56-43 (E01) Ignition switch ON 11 to 14 V
D56-106 (#80) - D56-43 (E01) Ignition switch ON 11 to 14 V




OK

12.CHECK FUEL INJECTOR OF MISFIRING CYLINDER

NG

12.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
a.

Check the injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (See page Engine / Hybrid System>3UR-FBE FUEL>FUEL INJECTOR>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

13.CHECK AIR INDUCTION SYSTEM

NG

13.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system for vacuum leakage (See page Engine / Hybrid System>3UR-FBE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leakage from air induction system.




OK

14.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

14.CHECK FUEL PRESSURE

OK

15.READ VALUE USING TECHSTREAM (COOLANT TEMP)

NG

33.CHECK FUEL LINE
15.READ VALUE USING TECHSTREAM (COOLANT TEMP)

OK

16.READ VALUE USING TECHSTREAM (MAF)

NG

16.READ VALUE USING TECHSTREAM (MAF)
a.

Connect the Techstream to the DLC3.


b.

Start the engine.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.


e.

Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.


f.

Read MAF with the engine speed at 3000 rpm.

Standard:

Between 18.0 gm/sec. and 27.0 gm/sec. (shift lever: N; A/C: Off).




OK

17.CHECK VALVE TIMING

NG

28.CHECK HARNESS AND CONNECTOR
17.CHECK VALVE TIMING

OK

28.CHECK HARNESS AND CONNECTOR

NG

18.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system for vacuum leakage (See page Engine / Hybrid System>3UR-FBE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leakage from air induction system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the air induction system (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

19.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

19.CHECK FUEL PRESSURE

OK

20.READ VALUE USING TECHSTREAM (COOLANT TEMP)

NG

33.CHECK FUEL LINE
20.READ VALUE USING TECHSTREAM (COOLANT TEMP)

OK

21.READ VALUE USING TECHSTREAM (MAF)

NG

21.READ VALUE USING TECHSTREAM (MAF)
a.

Connect the Techstream to the DLC3.


b.

Start the engine.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.


e.

Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.


f.

Read MAF with the engine speed at 3000 rpm.

Standard:

Between 18.0 gm/sec. and 27.0 gm/sec. (shift lever: N; A/C: Off).




OK

22.CHECK VALVE TIMING

NG

28.CHECK HARNESS AND CONNECTOR
22.CHECK VALVE TIMING

OK

23.INSPECT SPARK PLUG

NG

23.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the spark plug (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

24.CHECK FOR SPARK (SPARK TEST)

NG

24.CHECK FOR SPARK (SPARK TEST)
a.

Perform a spark test (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:

If the result of the spark test is normal, proceed to the next step.




NEXT

25.CHECK CYLINDER COMPRESSION PRESSURE
25.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>3UR-FBE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

26.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50, #60, #70 AND/OR #80 VOLTAGE)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

26.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50, #60, #70 AND/OR #80 VOLTAGE)
U152965E01
0.15,0.993 0.445,1.163 0.295,0.170 10 D56 0.068,0.039 2.416,0.395 2.348,0.356 10 Front view of wire harness connector: (to ECM) 1.883,0.965 2.169,1.120 0.286,0.156 10 E01 3.056,2.533 3.323,2.688 0.267,0.156 10 #10 3.02,1.054 3.287,1.210 0.267,0.156 10 #30 2.48,0.986 2.747,1.142 0.267,0.156 10 #50 2.14,2.895 2.410,3.051 0.271,0.156 10 #60 2.39,2.648 2.675,2.804 0.286,0.156 10 #40 2.785,2.795 3.042,2.951 0.258,0.156 10 #20 3.159,2.51 2.537,1.971 false 2.636,1.158 2.342,1.977 false 3.135,1.231 2.445,1.977 false 2.239,1.725 2.033,1.146 false 2.538,2.098 2.893,2.786 false 2.445,2.098 2.554,2.64 false 2.263,2.889 2.343,2.109 false 1.839,2.655 2.106,2.811 0.267,0.156 10 #80 2.004,2.65 2.235,2.109 false 1.44,2.9 1.707,3.056 0.267,0.156 10 #70 1.625,2.885 2.249,1.952 false

a.

Disconnect the D56 ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
D56-86 (#10) - D56-43 (E01) Ignition switch ON 11 to 14 V
D56-109 (#20) - D56-43 (E01) Ignition switch ON 11 to 14 V
D56-85 (#30) - D56-43 (E01) Ignition switch ON 11 to 14 V
D56-108 (#40) - D56-43 (E01) Ignition switch ON 11 to 14 V
D56-84 (#50) - D56-43 (E01) Ignition switch ON 11 to 14 V
D56-107 (#60) - D56-43 (E01) Ignition switch ON 11 to 14 V
D56-83 (#70) - D56-43 (E01) Ignition switch ON 11 to 14 V
D56-106 (#80) - D56-43 (E01) Ignition switch ON 11 to 14 V




OK

27.CHECK FUEL INJECTOR OF MISFIRING CYLINDER

NG

27.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
a.

Check the injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (See page Engine / Hybrid System>3UR-FBE FUEL>FUEL INJECTOR>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

28.CHECK HARNESS AND CONNECTOR

NG

28.CHECK HARNESS AND CONNECTOR
a.

Check the connection and terminal contact pressure of the connectors and wire harnesses between the mass air flow meter and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

HINT:

Repair any problems.




NEXT

29.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
29.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


j.

Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308.


k.

Check the DTC judgment result.

Result
Display (DTC Output) Proceed to
ABNORMAL
(P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 output)
A
NORMAL
(No DTC output)
B



A

30.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

B

END

30.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the D3 MAF meter connector.


b.

Disconnect the D56 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D3-3 (VG) - D56-74 (VG) Always Below 1 Ω
D3-2 (E2G) - D56-75 (E2G) Always Below 1 Ω
D3-3 (VG) or D56-74 (VG) - Body ground Always 10 kΩ or higher




OK

31.REPLACE MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

31.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL).

HINT:
·

If the results of the inspections performed in steps 16 and 21 indicated no problem, proceed to the next step without replacing the mass air flow meter.

·

Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).





NEXT

32.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
32.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


j.

Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308.


k.

Check the DTC judgment result.

Result
Display (DTC Output) Proceed to
NORMAL
(No DTC output)
A
ABNORMAL
(P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 output)
B



A

END

B

33.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.

HINT:

Perform "Inspection After Repair" after replacing the fuel pump (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

NG

REPAIR OR REPLACE FUEL LINE