Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049293 3UR-FBE ENGINE CONTROL _0235531 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P0340  Camshaft Position Sensor Circuit Malfunction  P0342  Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)  P0343  Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)  P0345  Camshaft Position Sensor "A" Circuit (Bank 2)  P0347  Camshaft Position Sensor "A" Circuit Low Input (Bank 2)  P0348  Camshaft Position Sensor "A" Circuit High Input (Bank 2)  


DESCRIPTION

The intake camshaft's Variable Valve Timing (VVT) sensor (VV1, 2 signal) consists of a magnet and MRE (Magnetic Resistance Element).

The intake camshaft has 3 teeth on its outer circumference. When the camshaft rotates, changes occur in the air gaps between the teeth and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the camshaft rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

The crankshaft position sensor plate has 34 teeth. The pickup coil generates 34 signals for each crankshaft revolution. Based on a combination of the VVT signal and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.

DTC No. DTC Detection Condition Trouble Area
P0340
P0345
No VVT sensor signal to ECM during engine running
(1 trip detection logic)
·

Open or short in VVT sensor (for intake side) circuit

·

VVT sensor (for intake side)

·

Intake camshaft

·

Jumped tooth of timing chain

·

ECM


P0342
P0347
Output voltage of VVT sensor less than 0.3 V for 4 seconds
(1 trip detection logic)
·

Open or short in VVT sensor (for intake side) circuit

·

VVT sensor (for intake side)

·

Intake camshaft

·

Jumped tooth of timing chain

·

ECM


P0343
P0348
Output voltage of VVT sensor more than 4.7 V for 4 seconds
(1 trip detection logic)
·

Open or short in VVT sensor (for intake side) circuit

·

VVT sensor (for intake side)

·

Intake camshaft

·

Jumped tooth of timing chain for intake camshaft

·

ECM



A217926E02
0.218,1.183 0.448,1.348 0.230,0.165 10 NE 0.145,1.733 0.449,1.885 0.304,0.151 10 VV1 0.149,2.105 0.448,2.251 0.299,0.145 10 VV2 2.85,1.275 3.186,1.424 0.336,0.149 10 GND 2.85,2.195 3.186,2.344 0.336,0.149 10 GND 2.85,1.818 3.186,1.967 0.336,0.149 10 GND 1.1,2.509 2.021,2.650 0.921,0.141 10 20 msec./DIV. 2.685,0.797 3.249,0.953 0.563,0.156 10 5 V/DIV. 0.102,0.078 2.419,0.234 2.318,0.156 10 VV1, VV2 and NE Signal Waveforms

Reference: Inspection using an oscilloscope

Standard:
Tester Connection Tool Setting Condition Specified Condition
D56-110 (NE+) - D56-111 (NE-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
D56-92 (VV1+) - D56-91 (VV1-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
D56-87 (VV2+) - D56-88 (VV2-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown


HINT:

VV1+ and VV2+ stand for the VVT sensor (for intake side) signal, and NE+ stands for the CKP sensor signal.



MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the camshaft revolving, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

When the sensor output voltage remains at less than 0.3 V, or more than 4.7 V for more than 4 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Related DTCs P0340: VVT position sensor (for Bank 1) verify pulse input
P0342: VVT position sensor (for Bank 1) range check (low voltage)
P0343: VVT position sensor (for Bank 1) range check (high voltage)
P0345: VVT position sensor (for Bank 2) verify pulse input
P0347: VVT position sensor (for Bank 2) range check (low voltage)
P0348: VVT position sensor (for Bank 2) range check (high voltage)
Required Sensors/Components (Main) VVT position sensor (for Bank 1 and 2)
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous
Duration 5 seconds: P0340, P0345
4 seconds: Others
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

P0340, P0345 (Verify pulse input):
Monitor runs whenever following DTCs are not stored None
VVT sensor voltage 0.3 to 4.7 V
Engine speed 600 rpm or more
Battery voltage 8 V or more
Starter OFF
Ignition switch ON
Camshaft position sensor range check failure (P0342, P0343, P0347, P0348) Not detected

P0342, P0343, P0347, P0348 (Low voltage, High voltage):
Monitor runs whenever following DTCs are not stored None
Starter OFF
Ignition switch ON
Time after ignition switch off to ON 2 seconds or more
Battery Voltage 8 V or more
Camshaft position sensor verify pulse input failure (P0340, P0345) Not detected

TYPICAL MALFUNCTION THRESHOLDS

P0340, P0345 (Verify pulse input):
VVT sensor signal No signal

P0342, P0347 (Low voltage):
VVT sensor voltage Less than 0.3 V

P0343, P0348 (High voltage):
VVT sensor voltage More than 4.7 V

COMPONENT OPERATING RANGE

VVT sensor voltage 0.3 to 4.7 V

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more [A].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

9.

Read the pending DTC.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0340, P0342, P0343, P0345, P0347 or P0348.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



13.

If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.

14.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A179939E01
1.531,1.208 1.748,1.359 0.217,0.151 10 VC 1.847,1.3 1.945,1.450 0.099,0.151 10 3 1.379,1.587 1.746,1.737 0.367,0.151 10 VVL+ 1.847,1.678 1.945,1.829 0.099,0.151 10 1 1.413,1.965 1.747,2.115 0.333,0.151 10 VVL- 1.847,2.056 1.945,2.207 0.099,0.151 10 2 0.596,2.236 0.876,2.396 0.280,0.161 10 D22 0.596,2.387 3.033,2.569 2.437,0.182 10 VVT Sensor (for Intake Side of Bank 1) 1.531,2.857 1.748,3.008 0.217,0.151 10 VC 1.847,2.949 1.945,3.100 0.099,0.151 10 3 1.356,3.224 1.746,3.375 0.390,0.151 10 VVR+ 1.847,3.327 1.945,3.478 0.099,0.151 10 1 1.388,3.602 1.746,3.753 0.359,0.151 10 VVR- 1.847,3.706 1.945,3.856 0.099,0.151 10 2 0.596,3.885 0.876,4.046 0.280,0.161 10 D23 0.596,4.037 3.033,4.218 2.437,0.181 10 VVT Sensor (for Intake Side of Bank 2) 4.761,1.208 5.037,1.359 0.276,0.151 10 D56 5.106,1.208 5.487,1.359 0.380,0.151 10 VCV2 4.814,1.034 4.986,1.185 0.172,0.151 10 66 4.761,1.586 5.037,1.737 0.276,0.151 10 D56 5.106,1.586 5.487,1.737 0.380,0.151 10 VV1+ 4.814,1.412 4.986,1.563 0.172,0.151 10 92 4.761,1.965 5.037,2.115 0.276,0.151 10 D56 5.106,1.965 5.487,2.115 0.380,0.151 10 VV1- 4.814,1.791 4.986,1.941 0.172,0.151 10 91 4.761,3.233 5.037,3.383 0.276,0.151 10 D56 5.106,3.233 5.487,3.383 0.380,0.151 10 VV2+ 4.814,3.059 4.986,3.209 0.172,0.151 10 87 4.761,3.611 5.037,3.762 0.276,0.151 10 D56 5.106,3.611 5.487,3.762 0.380,0.151 10 VV2- 4.814,3.437 4.986,3.588 0.172,0.151 10 88 5.632,4.26 5.968,4.410 0.336,0.151 10 ECM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)
U153066E03
1.99,2.198 2.74,2.542 true 0.083,0.052 2.417,0.427 2.333,0.375 10 false Front view of wire harness connector: (to VVT Sensor) 0.271,1.615 0.542,1.813 0.271,0.198 10 false D22 0.271,1.969 0.542,2.167 0.271,0.198 10 false D23 0.646,1.615 0.813,1.813 0.167,0.198 10 false *1 0.646,1.958 0.813,2.156 0.167,0.198 10 false *2 2.792,2.479 3.01,2.625 0.219,0.146 10 false VC 0.24,3.021 1.104,3.188 0.865,0.167 10 false *2: for Bank 2 0.24,2.635 1.104,2.802 0.865,0.167 10 false *1: for Bank 1

a.

Disconnect the D22 or D23 VVT sensor (for intake side) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
D22-3 (VC) - Body ground Ignition switch ON 4.5 to 5.0 V
D23-3 (VC) - Body ground Ignition switch ON 4.5 to 5.0 V




OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE SIDE) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE SIDE) - ECM)
a.

Disconnect the D22 or D23 VVT sensor (for intake side) connector.


b.

Disconnect the D56 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D22-1 (VVL+) - D56-92 (VV1+) Always Below 1 Ω
D22-2 (VVL-) - D56-91 (VV1-) Always Below 1 Ω
D23-1 (VVR+) - D56-87 (VV2+) Always Below 1 Ω
D23-2 (VVR-) - D56-88 (VV2-) Always Below 1 Ω
D22-1 (VVL+) or D56-92 (VV1+) - Body ground Always 10 kΩ or higher
D22-2 (VVL-) or D56-91 (VV1-) - Body ground Always 10 kΩ or higher
D23-1 (VVR+) or D56-87 (VV2+) - Body ground Always 10 kΩ or higher
D23-2 (VVR-) or D56-88 (VV2-) - Body ground Always 10 kΩ or higher




OK

3.CHECK SENSOR INSTALLATION (VVT SENSOR (FOR INTAKE SIDE))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (VVT SENSOR (FOR INTAKE SIDE))
a.
A380333E01
1.667,1.563 2.365,1.75 0.698,0.188 10 false Clearance 0.49,1.813 0.792,2.01 0.302,0.198 10 false OK 2.635,1.844 2.938,2.042 0.302,0.198 10 false NG

Check the VVT sensor (for intake side) installation.

OK:

Sensor is installed correctly.




OK

4.CHECK INTAKE CAMSHAFT (TEETH)

NG

4.CHECK INTAKE CAMSHAFT (TEETH)
a.

Check the teeth of the camshaft.

OK:

Teeth do not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the camshaft assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND)

NG

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND)

OK

6.REPLACE VVT SENSOR (FOR INTAKE SIDE)

NG

6.REPLACE VVT SENSOR (FOR INTAKE SIDE)
a.

Replace the VVT sensor (for intake side) (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>CAMSHAFT POSITION SENSOR>REMOVAL).



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Start the engine.


f.

Refer to the confirmation driving pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


h.

Read DTCs.

Result
Display (DTC Output) Proceed to
No output A
P0340, P0342, P0343, P0345, P0347 or P0348 B

HINT:

If the engine does not start, replace the ECM.




A

END

B