Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049293 3UR-FBE ENGINE CONTROL _0235531 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P060B  Internal Control Module A/D Processing Performance  


DESCRIPTION

This DTC is output when a communication error occurs in the ECM.

DTC No. DTC Detection Condition Trouble Area
P060B ECM main CPU communication error ECM

MONITOR STRATEGY

Related DTCs None
Required Sensors/Components (Main) ECM
Required Sensors/Components (Related) -
Frequency of Operation Once per driving cycle
Duration 2 times: Case 2
10 times: Case 1
30 times: Case 3 and 4
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Case 1 and 4
Monitor runs whenever following DTCs not present None
Both of the following conditions are met -
Battery voltage 8 V or more
Starter OFF

Case 2 and 3
Monitor runs whenever following DTCs not present None

TYPICAL MALFUNCTION THRESHOLDS

Case 1
Internal control module serial communication Fail

Case 2
AD converter Fail

Case 3
Knock sensor circuit Fail

Case 4
Knock sensor serial communication Fail

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Wait 16 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTC.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P060B.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:

If the judgment result shows ABNORMAL, the system has a malfunction.


12.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

NOTICE:

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC

b.

Turn the ignition switch off.


c.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.


d.

Connect the cable to the negative (-) battery terminal.


e.

Turn the ignition switch to ON.


f.

Wait 16 seconds or more.


g.

Check DTC.

Result
Result Proceed to
DTC is not output A
DTC P060B is output B
DTC P060B and P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D are output C



A

B

C

GO TO DTC (P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D)