| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P106B | The pressure detected by the canister pressure sensor (Vapor Pressure Pump*) and the pressure detected by the pressure sensor of either air switching valve (for Bank 1 or Bank 2) (Air pump pressure (Absolute)* or Air Pump2 Pressure (Absolute)*) differ by 6.98 kPa (52 mmHg) or more (2 trip detection logic). | ·
Canister pump module (Canister pressure sensor) ·
Air switching valve assembly |
*: Name of Data List item
This DTC is stored when a deviation from pressure sensor characteristics is detected.
The pressure detected by the canister pressure sensor and the pressures detected by the pressure sensors of both air switching valve assembly are checked 55 minutes after the ignition switch is turned off. If the pressure detected by the canister pressure sensor and the pressure detected by the pressure sensor of either air switching valve differ by a certain amount, the MIL is illuminated and a DTC is stored (2 trip detection logic).
Correct judgment may not be possible when the altitude is 4000 m (13120 ft.) or more.
| Related DTC | P106B: Evaporative emission system pressure sensor - Secondary Air injection (AIR) system pressure sensor correlation |
| Required Sensors/Components (Main) | ·
Canister pressure sensor ·
Pressure sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Once per driving cycle |
| Duration | Less than 65 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs are not stored | P0452, P0453 (Evaporative Emission System Pressure Sensor)
P2431, P2432, P2433, P2436, P2437, P2438 (Secondary air injection system pressure sensor) P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary air injection system) |
| Time elapsed after engine stop | 50 minutes |
| Time after ECM started by soak-timer | 60 seconds or more |
| Battery voltage | 10.5 V or higher |
| Intake air temperature | -10°C (14°F) or higher |
| Engine coolant temperature | -10°C (14°F) or higher |
| Difference between EVAP pressure and secondary air pressure sensor (bank 1) | More than 6.98 kPa (52 mmHg) |
| Difference between EVAP pressure and secondary air pressure sensor (bank 2) | More than 6.98 kPa (52 mmHg) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on [A].
Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
Start the engine and idle it for 10 seconds [B].
Turn the ignition switch off.
Soak the vehicle for 55 minutes [C].
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
Read the Pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P106B.
Check the DTC judgment result.
| Techstream Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit |
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [D] again.
If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
If a permanent DTC is output, the system is malfunctioning
If no permanent DTC is output, the system is normal.
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P106B is output | A |
| DTC P106B and other DTCs are output | B |
A
B
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menu: Powertrain / Engine and ECT / Data List / Vapor Pressure Pump, Air Pump Pressure sensor (Absolute) and Air Pump2 Pressure sensor (Absolute).
Compare the Vapor Pressure Pump, Air Pump Pressure sensor (Absolute) and Air Pump2 Pressure sensor (Absolute) data from the Data List with the current atmospheric pressure*.
*: Standard atmospheric pressure is 101 kPa (760 mmHg) at sea level. The atmospheric pressure decreases by approximately 1 kPa (7.5 mmHg) for every 100 m of elevation increase. Atmospheric pressure is also affected by weather conditions. The Atmosphere pressure listed in the Data List cannot be used as a reference for this check.
If you do not know the atmospheric pressure, refer to the Vapor Pressure Pump value of other vehicles in the workshop and check the difference in pressure.
| Result | Proceed to |
|---|---|
| If the Vapor Pressure Pump value differs from the atmospheric pressure by +/- 3.5 kPa (+/- 26.25 mmHg) or more | A |
| If the Air Pump Pressure sensor (Absolute) value differs from the atmospheric pressure by +/- 3.5 kPa (+/- 26.25 mmHg) or more | B |
| If the Air Pump2 Pressure sensor (Absolute) value differs from the atmospheric pressure by +/- 3.5 kPa (+/- 26.25 mmHg) or more |
A
B
Replace the canister pump module (See page Engine / Hybrid System>3UR-FBE EMISSION CONTROL>CANISTER>REMOVAL).
NEXT
Replace the air switching valve assembly (See page Engine / Hybrid System>3UR-FBE EMISSION CONTROL>AIR SWITCHING VALVE>REMOVAL).
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Vapor Pressure Pump, Air pump pressure (absolute) and Air Pump2 Pressure (Absolute).
Confirm that the difference between Vapor Pressure Pump and Air pump pressure (Absolute), and the difference between Vapor Pressure Pump and Air Pump2 Pressure (Absolute) are 3.5 kPa (+/- 26.25 mmHg) or less.
NEXT