Home › Engine / Hybrid System › 3UR-FBE EMISSION CONTROL › AIR SWITCHING VALVE
RM27L0U _51 Engine / Hybrid System _049299 3UR-FBE EMISSION CONTROL _0235587 AIR SWITCHING VALVE A

3UR-FBE EMISSION CONTROL  AIR SWITCHING VALVE  REMOVAL  


PROCEDURE

Hide 17104 1.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY

Hide 16711 3.REMOVE FAN SHROUD

Hide 16297 4.REMOVE NO. 9 WATER BY-PASS HOSE

a.
A307663E04
2.177,0.094 2.292,0.094 2.292,0.094 2.417,0.458 true 1.146,0.74 1.313,0.74 1.313,0.74 1.823,1.146 true 0.927,0.646 1.104,0.844 0.177,0.198 10 true *1 1.969,0.01 2.156,0.208 0.188,0.198 10 false *2

Slide the 2 clamps and remove the No. 9 water by-pass hose from the separator case and front water by-pass joint.

Text in Illustration
*1 No. 9 Water By-pass Hose
*2 No. 10 Water By-pass Hose


Hide 16293 5.REMOVE NO. 10 WATER BY-PASS HOSE

a.

Slide the 2 clamps and remove the No. 10 water by-pass hose from the separator case and front water by-pass joint.


Hide 16261G 6.REMOVE NO. 1 WATER BY-PASS HOSE

a.
A307665E03
1.323,0.104 1.115,0.104 1.115,0.104 0.635,0.375 true 1.25,1.75 1.25,1.365 false 1.188,1.792 1.375,1.969 0.188,0.177 10 false *1 1.354,0.021 1.604,0.219 0.25,0.198 10 false *2

Slide the 2 clamps and remove the No. 1 water by-pass hose from the front water by-pass joint and water inlet housing.

Text in Illustration
*1 No. 1 Water By-pass Hose
*2 No. 2 Water By-pass Hose


Hide 16264D 7.DISCONNECT NO. 2 WATER BY-PASS HOSE

a.

Slide the clamp and disconnect the No. 2 water by-pass hose from the front water by-pass joint.


Hide 16268A 8.DISCONNECT WATER BY-PASS PIPE HOSE (w/ Trailer Towing System)

a.
A158578

Remove the 3 bolts and disconnect the water by-pass pipe hose.


Hide 11212 9.REMOVE NO. 2 CYLINDER HEAD COVER

A307666

a.

Remove the No. 2 cylinder head cover.


Hide 77285D 10.DISCONNECT FUEL TUBE CLAMP

a.
A158580

Disconnect the fuel tube clamp from the bracket.


Hide 12611 11.REMOVE NO. 1 ENGINE COVER

A158581

a.

Remove the No. 1 engine cover.


Hide 16355 12.REMOVE FRONT WATER BY-PASS JOINT

a.

Disconnect the engine coolant temperature sensor connector.


b.
A307708

Remove the 4 nuts, front water by-pass joint and 2 gaskets.


Hide 16279 13.REMOVE NO. 3 WATER BY-PASS PIPE

A307664

HINT:

Perform this procedure only when replacement of the No. 3 water by-pass pipe is necessary.


a.

Remove the bolt and No. 3 water by-pass pipe.


Hide 17303 14.REMOVE AIR PIPE SUB-ASSEMBLY

a.
A158575E08
1,0.219 0.75,0.219 0.75,0.219 0.385,1.01 true 1.375,1.917 2.083,1.667 2.083,1.667 2.688,1.667 true 2.719,1.573 2.927,1.74 0.208,0.167 10 false *1 1.031,0.125 1.281,0.302 0.25,0.177 10 true *2

Slide the 2 clamps and disconnect the No. 2 air injection system hose and No. 3 air injection system hose.

Text in Illustration
*1 No. 2 air injection system hose
*2 No. 3 air injection system hose


b.

Disconnect the air switching valve connector.


c.

Disconnect the air switching valve connector clamp holder.


d.

Using a clip remover, detach the wire harness claw.


e.
A158582

Remove the 2 bolts and air pipe.


f.

Disconnect the 2 No. 1 air hoses from the air switching valve assembly.


Hide 25720 15.REMOVE AIR SWITCHING VALVE ASSEMBLY

a.
A158583

Disconnect the knock sensor connector.


b.

Remove the bolt and bracket.


c.

Disconnect the 2 air switching valve connectors.


d.
A158586

Remove the 3 bolts and air switching valve assembly.


Hide 17362 16.REMOVE NO. 2 AIR TUBE

a.
A158584

Remove the 2 bolts, No. 2 air tube and gasket.

NOTICE:

Be careful not to damage the installation surface of the gaskets.



Hide 17363Q 17.REMOVE NO. 3 AIR TUBE

a.
A158585

Remove the 2 bolts, No. 3 air tube and gasket.

NOTICE:

Be careful not to damage the installation surface of the gaskets.