Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › KNOCK SENSOR
RM27L0U _51 Engine / Hybrid System _049294 3UR-FE ENGINE CONTROL _0235540 KNOCK SENSOR A

3UR-FE ENGINE CONTROL  KNOCK SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the knock sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 89615 1.INSTALL KNOCK SENSOR

HINT:

Perform "Inspection After Repairs" after replacing the knock sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


a.
A184969E05
1.865,3.135 2.063,3.302 0.198,0.167 10 false *e 3.021,2.417 3.198,2.583 0.177,0.167 10 false *f 2.427,0.813 2.635,1.01 0.208,0.198 10 true *c 0.229,1.271 0.417,1.427 0.188,0.156 10 true *e 0.823,0.813 1.021,0.99 0.198,0.177 10 true *a 0.844,1.229 1.052,1.385 0.208,0.156 10 true *b 2.396,1.219 2.594,1.375 0.198,0.156 10 false *d 0.083,2.323 0.271,2.5 0.188,0.177 10 false *a 0.208,3.135 0.396,3.302 0.188,0.167 10 false *e 0.615,2.417 0.802,2.583 0.188,0.167 10 false *f 2.167,3.042 2.344,3.208 0.177,0.167 10 false 2° 2.104,2.875 2.354,3.031 0.25,0.156 10 false 10° 1.469,3.042 1.656,3.219 0.188,0.177 10 false 2° 1.417,2.875 1.667,3.031 0.25,0.156 10 false 10° 3.052,4.198 3.229,4.365 0.177,0.167 10 false 2° 3,4.031 3.26,4.188 0.26,0.156 10 false 10° 0.406,4.198 0.583,4.344 0.177,0.146 10 false 2° 0.354,4.042 0.594,4.208 0.24,0.167 10 false 10° 1.771,3.51 1.958,3.688 0.188,0.177 10 false *d 1.76,4.271 1.938,4.448 0.177,0.177 10 false *g 2.208,3.615 2.365,3.781 0.156,0.167 10 false *f 0.083,3.51 0.281,3.698 0.198,0.188 10 false *b 0.094,4.271 0.271,4.458 0.177,0.188 10 false *g 1.271,3.615 1.448,3.781 0.177,0.167 10 false *f 1.771,2.323 1.969,2.5 0.198,0.177 10 false *c

Install the 4 knock sensor with the 4 bolts so that the knock sensors are angled as shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

Text in Illustration
*a Bank 2 Sensor 1
*b Bank 1 Sensor 1
*c Bank 2 Sensor 2
*d Bank 1 Sensor 2
*e Front
*f Upper
*g Rear

NOTICE:

The acceptable installation angle of the knock sensor is between 10° upward and 2° downward from the horizontal position.



b.

Connect the 4 knock sensor connectors.