Home › Engine / Hybrid System › 3UR-FE EMISSION CONTROL › AIR SWITCHING VALVE
RM27L0U _51 Engine / Hybrid System _049300 3UR-FE EMISSION CONTROL _0235594 AIR SWITCHING VALVE A

3UR-FE EMISSION CONTROL  AIR SWITCHING VALVE  INSTALLATION  


PROCEDURE

Hide 17363Q 1.INSTALL NO. 3 AIR TUBE

a.
U151442E02
2.01,0.271 2.24,0.448 0.229,0.177 10 true *1

Install a new gasket and the No. 3 air tube with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 Identification Color

NOTICE:

Make sure that the gasket's claws are not caught between the air tube and electric air control valve assembly.


HINT:

The identification color on the flange is orange.



Hide 17362 2.INSTALL NO. 2 AIR TUBE

a.
U151441E02
2.094,0.229 2.302,0.417 0.208,0.188 10 true *1

Install a new gasket and the No. 2 air tube with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 Identification Color

NOTICE:

Make sure that the gasket's claws are not caught between the air tube and electric air control valve assembly.


HINT:

The identification color on the flange is blue.



Hide 25720 3.INSTALL ELECTRIC AIR CONTROL VALVE ASSEMBLY

a.

Install the electric air control valve assembly with the 3 bolts to the No. 1 heat exchanger cover.

Torque:
21 N*m (214 kgf*cm, 16 ft.*lbf)


b.

Connect the 2 electric air control valve connectors.


c.

Install the bracket to the electric air control valve assembly with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.

Connect the knock sensor connector.


Hide 17303 4.INSTALL AIR PIPE SUB-ASSEMBLY

a.

Connect the 2 No. 1 air hoses to the air pipe.


b.

Connect the air pipe to the electric air control valve assembly, and install the air pipe with the 2 bolts to the No. 1 heat exchanger cover.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.
A158575E08
1,0.219 0.75,0.219 0.75,0.219 0.385,1.01 true 1.375,1.917 2.083,1.667 2.083,1.667 2.688,1.667 true 2.719,1.573 2.927,1.74 0.208,0.167 10 false *1 1.031,0.125 1.281,0.302 0.25,0.177 10 true *2

Connect the air pump connector clamp holder.

Text in Illustration
*1 No. 2 air injection system hose
*2 No. 3 air injection system hose


d.

Attach the wire harness claw.


e.

Connect the electric air control valve connector.


f.

Connect the No. 2 air injection system hose and No. 3 air injection system hose, and slide the 2 clamps to secure the hose.


Hide 16279 5.INSTALL NO. 3 WATER BY-PASS PIPE

HINT:

Perform this procedure only when replacement of the No. 3 water by-pass pipe is necessary.


a.
A307664E02
0.292,0.708 0.406,0.708 0.406,0.708 0.719,0.969 true 0.365,1.302 0.51,1.302 0.51,1.302 0.74,1.042 false 0.156,1.198 0.323,1.385 0.167,0.188 10 true *a 0.083,0.625 0.25,0.802 0.167,0.177 10 true *b

Install the No. 3 water by-pass pipe to the front water by-pass joint with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*a Stopper
*b Protrusion

NOTICE:

Align the notch of the stopper with the protrusion of the front water by-pass joint.



Hide 16355 6.INSTALL FRONT WATER BY-PASS JOINT

a.

Install 2 new gaskets and the front water by-pass joint to the cylinder head with the 4 nuts.

Torque:
21 N*m (214 kgf*cm, 16 ft.*lbf)


b.

Connect the engine coolant temperature sensor connector.


Hide 16268A 7.CONNECT WATER BY-PASS PIPE HOSE (w/ Trailer Towing System)

a.

Connect the water by-pass pipe hose with the 3 bolts to the timing chain cover and front water by-pass joint.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16264D 8.CONNECT NO. 2 WATER BY-PASS HOSE

a.

Connect the No. 2 water by-pass hose to the water by-pass joint, and slide the clamp to secure the hose.


Hide 16261 9.INSTALL NO. 1 WATER BY-PASS HOSE

a.

Install the No. 1 water by-pass hose to the front water by-pass joint and water inlet housing, and slide the clamp to secure the hose.


Hide 16293 10.INSTALL NO. 10 WATER BY-PASS HOSE

a.
A307663E05
2.177,0.094 2.292,0.094 2.292,0.094 2.417,0.458 false 0.865,1.01 1.031,1.01 1.031,1.01 1.542,1.427 false 2.156,0.792 1.51,0.896 1.51,0.896 2.156,0.885 false 2.521,0.792 3.115,0.854 3.115,0.854 2.51,0.875 true 0.646,0.927 0.823,1.125 0.177,0.198 10 true *1 1.969,0.021 2.156,0.219 0.188,0.198 10 false *2 3.125,0.75 3.333,0.948 0.208,0.198 10 false *b 1.292,0.792 1.5,0.979 0.208,0.188 10 false *a

Install the No. 10 water by-pass hose to the separator case and front water by-pass joint, and slide the 2 clamps to secure the hose.

Text in Illustration
*1 No. 9 Water By-pass Hose
*2 No. 10 Water By-pass Hose
*a Paint Mark (Pink)
*b Paint Mark (White)

HINT:

Make sure that the color on the hose matches with the color on the case separator.



Hide 16297 11.INSTALL NO. 9 WATER BY-PASS HOSE

a.

Install the No. 9 water by-pass hose to the separator case and front water by-pass joint, and slide the 2 clamps to secure the hose.

HINT:

Make sure that the color on the hose matches with the color on the case separator.



Hide 12611 12.INSTALL NO. 1 ENGINE COVER

A158656

NOTICE:

Make sure that the No. 1 engine cover is level with the top surface of the intake port of the cylinder head for 1 and 2.


a.

Install the No. 1 engine cover.

HINT:
·

Align the No. 1 engine cover cutouts with the air tube.

·

Align the No. 1 engine cover with the air switching valve surface and cylinder head wall.




Hide 77285D 13.CONNECT FUEL TUBE CLAMP

a.

Connect the fuel tube clamp to the bracket.


Hide 11212 14.INSTALL NO. 2 CYLINDER HEAD COVER

A307709

NOTICE:

Make sure that the No. 2 cylinder head cover is level with the top surface of the intake port of the cylinder head.


a.

Install the No. 2 cylinder head cover.

HINT:
·

Align the No. 2 cylinder head cover cutout with the air tube.

·

Align the No. 2 cylinder head cover with the front water by-pass joint and cylinder head wall.




Hide 16711 15.INSTALL FAN SHROUD

Hide 17104 17.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY