Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › AIR FUEL RATIO SENSOR
RM27L0U _51 Engine / Hybrid System _049294 3UR-FE ENGINE CONTROL _0235541 AIR FUEL RATIO SENSOR A

3UR-FE ENGINE CONTROL  AIR FUEL RATIO SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 1.INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

HINT:

Perform "Inspection After Repairs" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


a.
A194685

Install the air fuel ratio sensor to the front No. 2 exhaust pipe assembly by hand.


b.
A194686E01
0.524,1.446 1.606,1.658 1.082,0.211 10 Fulcrum Length 2.8,1.581 3.188,1.788 0.387,0.207 10 SST 2.568,1.006 2.968,1.386 2.968,1.386 2.968,1.557 false

Using SST, tighten the air fuel ratio sensor.

SST
09224-00010  

·

without SST


Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

·

with SST


Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Make sure SST and the wrench are connected in a straight line.




Hide 89465 2.INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

HINT:

Perform "Inspection After Repairs" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


a.
A194685

Install the air fuel ratio sensor to the front exhaust pipe assembly by hand.


b.
A194686E01
0.524,1.446 1.606,1.658 1.082,0.211 10 Fulcrum Length 2.8,1.581 3.188,1.788 0.387,0.207 10 SST 2.568,1.006 2.968,1.386 2.968,1.386 2.968,1.557 false

Using SST, tighten the air fuel ratio sensor.

SST
09224-00010  

·

without SST


Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

·

with SST


Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Make sure SST and the wrench are connected in a straight line.




Hide 17450B 4.INSTALL FRONT NO. 2 EXHAUST PIPE SUB-ASSEMBLY

A184985

a.

Install a new gasket and the front No. 2 exhaust pipe sub-assembly to the exhaust manifold LH with 3 new nuts.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


b.

Install a new gasket and the front No. 2 exhaust pipe assembly to the front No. 3 exhaust pipe sub-assembly with the 2 bolts and 2 new nuts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


c.

Connect the air fuel ratio sensor connector.


d.

Connect the heated oxygen sensor connector and 2 clamps.