Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049294 3UR-FE ENGINE CONTROL _0235547 SFI SYSTEM J

3UR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunction detections by the ECM. When the ignition switch is turned to ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually: When the ignition switch is first turned to ON, the MIL should be illuminated and should then turn off when the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the Techstream.

WIRING DIAGRAM

A179944E01
6.183,4.417 6.519,4.562 0.336,0.145 10 ECM 5.503,0.626 5.681,0.768 0.177,0.142 10 24 5.457,0.791 5.724,0.940 0.267,0.150 10 A27 5.785,0.716 5.939,0.857 0.154,0.141 10 W 4.078,1.339 4.349,1.483 0.272,0.144 10 H37 3.871,0.694 4.052,0.843 0.180,0.149 10 20 5.211,0.701 5.316,0.843 0.105,0.142 10 5 4.115,0.697 4.396,0.843 0.281,0.145 10 IG+ 4.812,0.701 5.133,0.843 0.322,0.142 10 CHK 4.497,0.951 4.757,1.093 0.260,0.142 10 MIL 4.078,1.484 5.317,1.640 1.239,0.156 10 Combination Meter 3.431,0.919 3.745,1.075 0.315,0.156 10 MET 2.686,1.312 2.931,1.459 0.245,0.147 10 IG2 2.221,2.138 2.854,2.285 0.633,0.147 10 IG2 MAIN 0.661,2.133 0.968,2.289 0.306,0.156 10 AM2 0.829,4.004 1.291,4.158 0.461,0.155 10 Battery 0.726,0.918 0.824,1.058 0.098,0.140 10 5 1.791,0.915 1.914,1.058 0.123,0.143 10 6 0.869,0.917 1.172,1.058 0.303,0.141 10 AM2 1.465,0.917 1.708,1.058 0.244,0.141 10 IG2 0.836,1.407 1.263,1.555 0.427,0.148 10 H10 0.836,1.559 1.749,1.708 0.913,0.149 10 Ignition Switch

PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result
Result Proceed to
MIL remains ON A
MIL does not illuminate B



A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER MIL TURNS OFF
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Check if any DTCs have been stored. Note down any DTCs.



f.

Check if the MIL goes off.

Standard:

MIL goes off




OK

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the A27 ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.




OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
a.

Disconnect the A27 ECM connector.


b.

Disconnect the H37 combination meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A27-24 (W) or H37-5 (CHK) - Body ground Always 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the ignition switch is turned to ON.

OK:

MIL should be illuminated.




OK

SYSTEM OK

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Turn the ignition switch to ON.


b.

Start the engine.

Result
Result Proceed to
Engine starts A
Engine does not start* B

HINT:

*: The Techstream cannot communicate with the ECM.




A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)

B

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
a.

Disconnect the A27 ECM connector.


b.

Disconnect the H37 combination meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A27-24 (W) - H37-5 (CHK) Always Below 1 Ω




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR