Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049294 3UR-FE ENGINE CONTROL _0235547 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  P0020  Camshaft Position "A" Actuator Circuit (Bank 2)  


DESCRIPTION

·

This DTC is designed to detect opens or shorts in the camshaft oil control valve (OCV) circuit. If the OCV duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

·

The VVT (variable valve timing) system adjusts the intake valve timing to improve the driveability. The engine oil pressure turns the camshaft actuator to adjust the valve timing. The OCV is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.


A192077E01
4.651,0.815 6.372,1.026 1.721,0.211 10 VVT Sensor (CMP Sensor) 4.651,1.325 5.477,1.485 0.825,0.161 10 CKP Sensor 0.068,0.015 1.618,0.267 1.550,0.253 10 VVT System: 2.333,1.96 3.609,2.134 1.277,0.174 10 Target Valve Timing 2.333,1.287 3.609,1.462 1.277,0.174 10 Actual Valve Timing 2.683,2.695 3.397,2.870 0.714,0.174 10 Correction 2.822,3.204 3.223,3.378 0.402,0.174 10 ECM 1.599,3.747 3.758,3.922 2.160,0.174 10 Camshaft Oil Control Valve (OCV) 0.166,2.69 0.860,2.864 0.695,0.174 10 Duty-cycle 4.651,1.827 5.490,1.981 0.839,0.154 10 MAF Meter 4.651,2.854 5.449,3.042 0.797,0.188 10 ECT Sensor 4.651,2.344 5.018,2.511 0.367,0.167 10 TPS 4.651,3.353 5.004,3.506 0.353,0.154 10 VSS 0.313,4.269 1.682,4.474 1.369,0.205 10 Engine Oil Pressure 3.659,4.217 4.885,4.400 1.225,0.184 10 Camshaft Actuator 3.883,4.917 4.984,5.101 1.100,0.184 10 Intake Camshaft 2.562,4.571 2.842,4.275 2.842,4.275 3.607,4.275 false 3.177,4.781 3.32,5.008 3.32,5.008 3.852,5.008 false

DTC Code DTC Detection Condition Trouble Area
P0010 An open or short in the Camshaft Oil Control Valve (OCV) for intake side (for Bank 1) circuit (1 trip detection logic).
·

Open or short in Camshaft Oil Control Valve (OCV) (for intake side of Bank 1) circuit

·

OCV (for intake side of Bank 1)

·

ECM


P0020 An open or short in the OCV for intake side (for Bank 2) circuit (1 trip detection logic).
·

Open or short in OCV (for intake side of Bank 2) circuit

·

OCV (for intake side of Bank 2)

·

ECM



HINT:

This DTC relates to the Oil Control Valve (OCV).


MONITOR DESCRIPTION

This DTC is designed to detect opens or shorts in the camshaft oil control valve (OCV) circuit. If the OCV duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

MONITOR STRATEGY

Related DTCs P0010: VVT OCV range check (Bank 1)
P0020: VVT OCV range check (Bank 2)
Required Sensors/Components (Main) Intake VVT OCV
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration 1 second
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever following DTCs not stored None
All of following conditions met -
Starter OFF
Ignition switch ON
Time after ignition switch off to ON 0.5 seconds or more

Case 1
One of following conditions met -
A. All of following conditions met -
Battery voltage 11 to 13 V
Target duty cycle Less than 70%
B. All of following conditions met -
Battery voltage 13 V or more
Target duty cycle Less than 80%

Case 2
Current cut status Not cut

TYPICAL MALFUNCTION THRESHOLDS

Case 1
Output duty cycle 100% or more

Case 2
Output duty cycle 3% or less

COMPONENT OPERATING RANGE

VVT OCV duty cycle 3 to 100%

CONFIRMATION DRIVING PATTERN

1.
A198818E35
0.071,1.648 1.257,1.825 1.186,0.177 10 Ignition Switch ON 3.178,1.526 3.389,1.709 0.211,0.184 10 [A] 4.817,2.976 5.032,3.149 0.215,0.173 10 [B] 3.045,2.338 3.722,2.480 0.677,0.142 10 5 seconds

2.

Connect the Techstream to the DLC3.

3.

Turn the ignition switch to ON and turn the Techstream on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation)

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the Techstream on [A].

7.

Wait 5 seconds.

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

9.

Read the Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0010 or P0020.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:

If the judgment result shows ABNORMAL, the system has a malfunction.


13.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A178641E17
5.854,4.115 6.208,4.302 0.354,0.188 10 false ECM 5.406,0.49 5.823,0.698 0.417,0.208 10 false OC1+ 5.406,1.219 5.823,1.385 0.417,0.167 10 false OC1- 5.406,2.469 5.844,2.625 0.438,0.156 10 false OC2+ 5.406,3.198 5.844,3.354 0.438,0.156 10 false OC2- 0.094,1.656 2.563,1.865 2.469,0.208 10 false OCV for Intake Camshaft (for Bank 1) 0.094,3.625 2.583,3.833 2.49,0.208 10 false OCV for Intake Camshaft (for Bank 2) 0.094,1.469 0.406,1.635 0.313,0.167 10 false D26 0.094,3.458 0.375,3.625 0.281,0.167 10 false D27 1.448,0.479 1.573,0.667 0.125,0.188 10 false 1 1.458,1.219 1.573,1.396 0.115,0.177 10 false 2 1.448,2.427 1.573,2.615 0.125,0.188 10 false 1 1.458,3.167 1.573,3.344 0.115,0.177 10 false 2 5.115,3.125 5.344,3.281 0.229,0.156 10 false 51 5.115,2.385 5.333,2.573 0.219,0.188 10 false 52 5.115,1.156 5.323,1.323 0.208,0.167 10 false 57 5.115,0.417 5.333,0.615 0.219,0.198 10 false 58 5.063,0.604 5.375,0.781 0.313,0.177 10 false D56 5.063,1.333 5.385,1.531 0.323,0.198 10 false D56 5.063,2.563 5.375,2.75 0.313,0.188 10 false D56 5.063,3.313 5.417,3.49 0.354,0.177 10 false D56

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK DTC
a.

Clear DTC after recording the freeze frame data and DTC (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).


b.

Turn the ignition switch off.


c.

Allow the engine to idle and check DTC.


d.

Check that P0010 or P0020 is not present.

OK:

P0010 or P0020 is not present.




OK

NG

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft oil control valve assembly (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (OCV - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (OCV - ECM)
a.

Disconnect the D26 or D27 OCV connector.


b.

Disconnect the D56 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D26-1 - D56-58 (OC1+) Always Below 1 Ω
D27-1 - D56-52 (OC2+) Always Below 1 Ω
D26-2 - D56-57 (OC1-) Always Below 1 Ω
D27-2 - D56-51 (OC2-) Always Below 1 Ω
D26-1 or D56-58 (OC1+) - Body ground Always 10 kΩ or higher
D27-1 or D56-52 (OC2+) - Body ground Always 10 kΩ or higher
D26-2 or D56-57 (OC1-) - Body ground Always 10 kΩ or higher
D27-2 or D56-51 (OC2-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR