Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049294 3UR-FE ENGINE CONTROL _0235547 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P144C  Open in Secondary Air Injection System Heater Control Circuit  P144D  Short in Secondary Air Injection System Heater Control Circuit  


DESCRIPTION

The ECM operates the air pump heater relay which causes the air pump heater to operate.

DTC No. DTC Detection Condition Trouble Area
P144C Open or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic).
·

Open or short in air pump heater relay circuit

·

Air pump heater relay

·

ECM


P144D Open or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic).
·

Open or short in air pump heater relay circuit

·

Air pump heater relay

·

ECM



MONITOR DESCRIPTION

These DTCs are designed to detect a malfunction in the air pump heater relay circuit. When the system is normal, the battery voltage is applied to terminal HAI1 of the ECM while the air pump heater relay is turned off, and the battery voltage is not applied to terminal HAI1 of the ECM while the air pump heater relay is turned on. The ECM illuminates the MIL and stores a DTC when either one of the following conditions is detected.

·

The battery voltage is not applied to terminal HAI1 while the air pump heater relay is off.

·

The battery voltage is applied to terminal HAI1 while the air pump heater relay is on.


MONITOR STRATEGY

Related DTCs P144C: Air pump heater relay circuit range check (Low voltage)
P144D: Air pump heater relay circuit range check (High voltage)
Required Sensors/Components (Main) Air pump heater relay
Required Sensors/Components (Related) -
Frequency of operation Continuous
Duration 5 seconds
MIL operation Immediate
Sequence of operation None

TYPICAL ENABLING CONDITIONS

Case 1
Monitor runs whenever following DTCs not stored None
Current air pump heater relay (AIR PMP HTR) ON
Last air pump heater relay (AIR PMP HTR) ON
Battery voltage 8 V or more
Ignition switch ON
Starter OFF

Case 2
Monitor runs whenever following DTCs not stored None
Current air pump heater relay (AIR PMP HTR) OFF
Last air pump heater relay (AIR PMP HTR) OFF
Battery voltage 8 V or more
Ignition switch ON
Starter OFF

TYPICAL MALFUNCTION THRESHOLDS

P144C
Air pump heater relay output terminal voltage Low

P144D
Air pump heater relay output terminal voltage High

CONFIRMATION DRIVING PATTERN

A231721E10
0.936,1.236 1.314,1.392 0.378,0.156 10 Idling 0.124,1.625 1.307,1.781 1.184,0.156 10 Ignition Switch ON 0.159,2.025 1.308,2.181 1.149,0.156 10 Ignition Switch off 1.798,1.485 2.008,1.678 0.210,0.192 10 [A] 2.191,1.075 2.401,1.267 0.210,0.192 10 [B] 4.818,2.896 5.028,3.088 0.210,0.192 10 [C] 2.87,2.27 4.158,2.440 1.288,0.170 10 10 seconds or more

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine and wait 10 seconds or more [B].

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

8.

Read the pending DTC.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P144C or P144D.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:

If the judgment result shows ABNORMAL, the system has a malfunction.


12.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT AIR PUMP HEATER RELAY
a.

Inspect the air pump heater relay (AI-HTR) (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION).



OK

2.CHECK AIR PUMP HEATER RELAY (POWER SOURCE)

NG

REPLACE AIR PUMP HEATER RELAY

2.CHECK AIR PUMP HEATER RELAY (POWER SOURCE)
a.

Remove the air pump heater relay (AI-HTR).


b.
A258729E13
0.12,0.084 1.908,0.268 1.788,0.184 10 Engine Room Relay Block: 1.586,1.487 2.074,1.668 0.488,0.181 10 AI-HTR

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
AI-HTR relay terminal 1 - Body ground Ignition switch ON 11 to 14 V



c.

Reinstall the air pump heater relay (AI-HTR).



OK

3.CHECK HARNESS AND CONNECTOR (ECM - AIR PUMP HEATER RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ECM - AIR PUMP HEATER RELAY)
a.

Remove the air pump heater relay (AI-HTR).


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
AI-HTR relay terminal 2 - D56-61 (HAI1) Always Below 1 Ω
AI-HTR relay terminal 2 or D56-61 (HAI1) - Body ground Always 10 kΩ or higher



d.

Reinstall the air pump heater relay (AI-HTR).


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR