Home › Engine / Hybrid System › 3UR-FE ENGINE MECHANICAL › CAMSHAFT
RM27L0U _51 Engine / Hybrid System _049296 3UR-FE ENGINE MECHANICAL _0235558 CAMSHAFT A

3UR-FE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


PROCEDURE

Hide 11302 1.REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY

a.

Remove the timing chain cover (See page Engine / Hybrid System>3UR-FE LUBRICATION>OIL PUMP>REMOVAL).


Hide 2.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the pulley set bolt.


b.

Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.

A160654E07
3.479,4.813 4.01,5.052 4.01,5.052 4.01,5.167 false 3.656,4.396 4.052,4.01 4.052,4.01 4.177,4.01 false 0.625,0.313 0.438,0.313 0.438,0.313 0.542,0.896 false 1.5,0.323 1.719,0.323 1.719,0.323 1.667,0.792 false 5.635,0.333 5.479,0.333 5.479,0.333 5.552,0.823 false 6.521,0.333 6.771,0.333 6.771,0.333 6.708,0.948 false 0.542,5.604 0.813,6.146 0.813,6.146 1.354,5.604 false 0.333,4.396 0.229,4.396 0.229,4.396 0.531,5.333 false 0.531,3.385 1.042,4.094 1.042,4.094 1.375,3.479 false 5.833,5.604 6.094,6.177 6.094,6.177 6.563,5.604 false 5.323,4.625 5.073,4.625 5.073,4.625 5.563,5.26 false 6.385,4.385 6.896,4.385 6.896,4.385 6.615,5.375 false 5.479,3.646 6,4.063 6,4.063 6.469,3.438 false 0.604,3.219 0.354,2.396 0.354,2.396 0.458,2.396 false 1.74,3.177 2.042,2.375 2.042,2.375 1.906,2.375 false 5.417,3.219 5.177,2.448 5.177,2.448 5.281,2.448 false 6.563,3.302 6.865,2.5 6.865,2.5 6.729,2.5 false 1.406,5.375 1.74,4.896 1.74,4.896 1.635,4.896 false 1.646,5.24 2.083,4.625 2.083,4.625 1.99,4.625 false 1.813,5.229 1.99,5.438 1.99,5.438 1.99,5.708 false 5.417,5.229 5.313,5.375 5.313,5.375 5.313,5.604 false 5.563,4.854 5.448,4.854 5.448,4.854 5.802,5.385 false 3.656,5.208 4.51,5.375 0.854,0.167 10 false Timing Mark 4.229,3.927 4.542,4.125 0.313,0.198 10 false Key 0.688,0.25 1.521,0.427 0.833,0.177 10 false Timing Mark 5.708,0.25 6.542,0.427 0.833,0.177 10 false Timing Mark 0.198,6.188 1.573,6.396 1.375,0.208 10 false Timing Mark Position 0.521,4.115 1.771,4.323 1.25,0.208 10 true Knock Pin Position 5.375,4.552 6.604,4.802 1.229,0.25 10 true Approximately 45° 5.573,4.781 6.698,4.979 1.125,0.198 10 true Approximately 32° 5.5,6.208 6.875,6.417 1.375,0.208 10 false Timing Mark Position 5.427,4.125 6.677,4.333 1.25,0.208 10 true Knock Pin Position 0.552,2.302 1.927,2.479 1.375,0.177 10 false Timing Mark Position 5.354,2.396 6.729,2.573 1.375,0.177 10 false Timing Mark Position 0.365,4.323 1.594,4.573 1.229,0.25 10 true Approximately 2° 0.479,4.823 1.708,5.073 1.229,0.25 10 false Approximately 16° 0.802,4.563 1.948,4.76 1.146,0.198 10 true Approximately 45° 1.708,5.708 2.198,6.083 0.49,0.375 10 false Toward Ceiling 5.031,5.604 5.521,5.979 0.49,0.375 10 false Toward Ceiling 5.167,4.313 6.396,4.563 1.229,0.25 10 true Approximately 18° 3.094,1.021 4.115,1.396 1.021,0.375 10 false Toward Ceiling

HINT:

If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.



Hide 13540 3.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY (for LH Side)

a.
A174140E04
1.583,1.208 2.115,0.271 2.115,0.271 2.344,0.271 true 1.417,1.281 1.25,1.708 1.25,1.708 1.146,1.708 true 2.406,0.177 2.99,0.635 0.583,0.458 10 true Plunger 0.094,1.583 1.01,1.781 0.917,0.198 10 true Stopper Plate

Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.


b.
A174141E03
2.177,1.198 2.604,0.438 2.604,0.438 2.729,0.438 true 2.073,1.313 2.563,1.427 2.563,1.427 2.76,1.427 true 2.771,0.365 3.292,0.563 0.521,0.198 10 false Plunger 2.781,1.292 3.313,1.646 0.531,0.354 10 false Stopper Plate

Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate hole.


c.
A160733

Remove the 2 bolts, chain tensioner and gasket.


Hide 13559 4.REMOVE CHAIN TENSIONER SLIPPER (for LH Side)

A178535

Hide 13561 5.REMOVE NO. 1 CHAIN VIBRATION DAMPER (for LH Side)

a.
A178536

Remove the 2 bolts and chain vibration damper.


Hide 13506 6.REMOVE CHAIN SUB-ASSEMBLY (for LH Side)

a.
A160655E05
1.865,2.208 1.958,1.844 1.958,1.844 2.104,1.844 false 1.292,2.917 1.583,2.917 1.583,2.917 2.135,2.385 false 2.156,1.75 2.417,1.917 0.26,0.167 10 false Pin 0.677,2.813 1.24,2.99 0.563,0.177 10 false Plunger 2.198,0.5 2.667,0.927 0.469,0.427 10 true Push

While pushing down the No. 3 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.


b.
A160656E05
1.031,0.042 1.375,0.229 0.344,0.188 10 false Turn 2.854,0.333 3.219,0.531 0.365,0.198 10 true Hold

Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.

NOTICE:
·

Be careful not to damage the cylinder head with the wrench.

·

Do not disassemble the camshaft timing gear.




c.
A160657E04
1.896,0.708 2.292,1.021 0.396,0.313 10 true Turn 3.031,0.729 3.354,0.896 0.323,0.167 10 false Hold

Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.

NOTICE:

Be careful not to damage the cylinder head with the wrench.



d.

Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket LH.


e.

Remove the No. 1 and No. 2 chains from the gears.


Hide 13560A 7.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A148225

Remove the 2 bolts and chain tensioner.


Hide 13540 8.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY (for RH Side)

a.
A174142E04
0.854,0.188 0.979,0.188 0.979,0.188 1.521,0.74 true 1.24,1.854 1.333,1.854 1.333,1.854 1.458,0.896 true 0.229,0.063 0.802,0.26 0.573,0.198 10 true Plunger 0.313,1.771 1.25,1.948 0.938,0.177 10 false Stopper Plate

Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.


b.
A174143E03
2.375,0.729 2.604,0.125 2.604,0.125 2.708,0.125 true 2.344,0.948 2.635,1.375 2.635,1.375 2.75,1.375 true 2.74,0.063 3.281,0.25 0.542,0.188 10 true Plunger 2.781,1.292 3.323,1.698 0.542,0.406 10 true Stopper Plate

Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate hole.


c.
A150146

Remove the 2 bolts and chain tensioner.


Hide 13559 9.REMOVE CHAIN TENSIONER SLIPPER (for RH Side)

A178486

Hide 13561 10.REMOVE NO. 1 CHAIN VIBRATION DAMPER (for RH Side)

a.
A160658

Remove the 2 bolts and vibration damper.


Hide 13506 11.REMOVE CHAIN SUB-ASSEMBLY (for RH Side)

a.
A160659E03
1.323,2.625 1.385,2.333 1.385,2.333 1.479,2.333 false 1.01,2.74 1.01,2.927 false 1.531,2.25 1.781,2.427 0.25,0.177 10 false Pin 0.729,2.906 1.281,3.104 0.552,0.198 10 false Plunger 2.125,0.719 2.531,1.104 0.406,0.385 10 true Push

While raising up the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.


b.
A160660E01
2.387,0.03 2.762,0.216 0.375,0.186 10 Turn 1.219,0 1.532,0.170 0.313,0.170 10 Hold

Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.

NOTICE:
·

Be careful not to damage the cylinder head with the wrench.

·

Do not disassemble the camshaft timing gear.




c.
A160661E03
0.344,0.688 0.688,0.875 0.344,0.188 10 false Hold 1.552,0.458 1.917,0.75 0.365,0.292 10 true Turn

Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.

NOTICE:

Be careful not to damage the cylinder head with the wrench.



d.

Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket RH.


e.

Remove the No. 1 and No. 2 chains from the gears.


Hide 13550 12.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A148224

Remove the 2 bolts and chain tensioner.


Hide 13.REMOVE CAMSHAFT (for Bank 1)

A163591E04
0.896,2.583 1.771,2.896 1.771,2.896 2.49,2.552 false 1.406,2.927 2.104,3.104 0.698,0.177 10 false Knock Pin 1.292,2.135 1.5,2.323 0.208,0.188 10 false IN 2.865,2.135 3.083,2.302 0.219,0.167 10 false EX 0.708,2.094 1.073,2.333 0.365,0.24 10 false 45° 2.479,2.063 2.792,2.271 0.313,0.208 10 false 3°

a.

Make sure that the knock pin of the camshaft is positioned as shown in the illustration.


b.
A163592E10
0.417,1.729 0.531,1.917 0.115,0.188 10 false 1 0.438,0.198 0.552,0.385 0.115,0.188 10 true 2 1.021,1.729 1.135,1.917 0.115,0.188 10 false 3 1.063,0.198 1.177,0.385 0.115,0.188 10 true 4 1.604,1.74 1.719,1.927 0.115,0.188 10 false 5 1.625,0.198 1.74,0.385 0.115,0.188 10 true 6 2.167,1.74 2.281,1.927 0.115,0.188 10 false 7 2.167,0.198 2.281,0.385 0.115,0.188 10 true 8 2.865,1.729 2.979,1.917 0.115,0.188 10 true 9 2.854,0.208 3.031,0.396 0.177,0.188 10 true 10

Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.


c.
A163593E04
3.313,0.135 3.417,0.292 0.104,0.156 10 false 1 3.292,1.667 3.396,1.823 0.104,0.156 10 false 2 0.094,1.417 0.198,1.573 0.104,0.156 10 false 3 2.75,1.781 2.854,1.938 0.104,0.156 10 false 4 3.292,0.51 3.396,0.667 0.104,0.156 10 false 5 0.479,1.875 0.583,2.031 0.104,0.156 10 false 6 0.469,0 0.573,0.156 0.104,0.156 10 false 7 2.198,1.865 2.302,2.021 0.104,0.156 10 false 8 2.229,0 2.333,0.156 0.104,0.156 10 false 9 1.031,1.875 1.219,2.031 0.188,0.156 10 false 10 1.052,0.01 1.24,0.167 0.188,0.156 10 true 11 1.531,1.865 1.719,2.021 0.188,0.156 10 false 12 1.604,0 1.792,0.156 0.188,0.156 10 false 13 2.823,0.542 3.01,0.698 0.188,0.156 10 true 14 0.406,0.542 0.594,0.698 0.188,0.156 10 true 15 2.167,0.531 2.354,0.688 0.188,0.156 10 true 16 1.042,0.542 1.229,0.698 0.188,0.156 10 true 17 1.5,0.542 1.688,0.698 0.188,0.156 10 true 18

Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.

NOTICE:

Uniformly loosen the bolts while keeping the camshaft level.



d.

Remove the 6 bearing caps.

HINT:

Arrange the removed parts in the correct order.



e.

Remove the No. 3 and No. 4 camshafts.

HINT:

Arrange the removed parts in the correct order.



Hide 11104A 14.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

a.
A163594

Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

HINT:

Tape the screwdriver tip before use.


NOTICE:

Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.



Hide 15.REMOVE CAMSHAFT (for Bank 2)

A160683E04
0.698,2.604 1.552,2.875 1.552,2.875 2.083,2.688 false 0.417,2.073 0.74,2.25 0.323,0.177 10 false 55° 1.833,2.104 2.156,2.281 0.323,0.177 10 false 70° 1.188,2.906 1.865,3.094 0.677,0.188 10 false Knock Pin 2.563,2.115 2.76,2.271 0.198,0.156 10 false IN 1,2.104 1.271,2.302 0.271,0.198 10 false EX

a.

Make sure that the knock pin of the camshaft is positioned as shown in the illustration.


b.
A160684E10
0.365,0.188 0.479,0.344 0.115,0.156 10 false 1 0.365,1.646 0.479,1.802 0.115,0.156 10 true 2 0.958,0.208 1.073,0.365 0.115,0.156 10 true 3 1,1.625 1.115,1.781 0.115,0.156 10 true 4 1.542,0.208 1.656,0.365 0.115,0.156 10 false 5 1.552,1.646 1.667,1.802 0.115,0.156 10 true 6 2.115,0.229 2.229,0.385 0.115,0.156 10 true 7 2.125,1.656 2.24,1.813 0.115,0.156 10 true 8 2.802,0.198 2.917,0.354 0.115,0.156 10 true 9 2.771,1.646 2.958,1.802 0.188,0.156 10 true 10

Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.


c.
A160685E06
3.24,1.76 3.333,1.917 0.094,0.156 10 false 1 3.208,0.073 3.302,0.229 0.094,0.156 10 false 2 0.146,0.5 0.24,0.656 0.094,0.156 10 true 3 2.604,0.125 2.698,0.281 0.094,0.156 10 false 4 3.156,1.531 3.25,1.688 0.094,0.156 10 false 5 0.302,0.063 0.396,0.219 0.094,0.156 10 false 6 0.302,1.948 0.396,2.104 0.094,0.156 10 false 7 2.021,0.063 2.115,0.219 0.094,0.156 10 false 8 2.063,1.938 2.156,2.094 0.094,0.156 10 false 9 0.875,0.052 1.063,0.208 0.188,0.156 10 false 10 0.896,1.938 1.083,2.094 0.188,0.156 10 false 11 1.375,0.073 1.563,0.229 0.188,0.156 10 false 12 1.448,1.938 1.635,2.094 0.188,0.156 10 false 13 2.646,1.375 2.833,1.531 0.188,0.156 10 true 14 0.25,1.365 0.438,1.521 0.188,0.156 10 true 15 0.885,1.375 1.073,1.531 0.188,0.156 10 true 17 1.5,1.375 1.688,1.531 0.188,0.156 10 true 18 1.99,1.365 2.177,1.521 0.188,0.156 10 true 16

Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.

NOTICE:

Uniformly loosen the bolts while keeping the camshaft level.



d.

Remove the 6 bearing caps.

HINT:

Arrange the removed parts in the correct order.



e.

Remove the No. 1 and No. 2 camshafts.

HINT:

Arrange the removed parts in the correct order.



Hide 11103C 16.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

a.
A160735

Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

HINT:

Tape the screwdriver tip before use.


NOTICE:

Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.