Home › Engine / Hybrid System › 3UR-FE LUBRICATION › OIL PUMP
RM27L0U _51 Engine / Hybrid System _049306 3UR-FE LUBRICATION _0235629 OIL PUMP A

3UR-FE LUBRICATION  OIL PUMP  REMOVAL  


PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 16400 3.REMOVE RADIATOR ASSEMBLY

Hide 17880 5.REMOVE AIR CLEANER HOSE ASSEMBLY

Hide 87245C 6.DISCONNECT INLET HEATER WATER HOSE C

a.
A183230

Slide the clamp and disconnect the inlet heater water hose C from the water by-pass pipe sub-assembly.


Hide 87246C 7.DISCONNECT OUTLET HEATER WATER HOSE C

a.
A183228

Slide the clamp and disconnect the outlet heater water hose C from the No. 1 water by-pass pipe.


Hide 82121 8.SEPARATE ENGINE WIRE

Hide 82122 9.SEPARATE NO. 2 ENGINE WIRE

Hide 17343 11.DISCONNECT NO. 3 AIR INJECTION SYSTEM HOSE

Hide 17342 12.DISCONNECT NO. 2 AIR INJECTION SYSTEM HOSE

Hide 88320 13.SEPARATE COOLER COMPRESSOR ASSEMBLY

a.
A163332

Remove the 2 bolts, 2 nuts and 2 stud bolts, and disconnect the cooler compressor assembly.

HINT:

It is not necessary to completely remove the cooler compressor assembly. With the hoses connected to the cooler compressor assembly, hang the cooler compressor assembly on the vehicle body with a rope.



Hide 23902 14.SEPARATE NO. 2 FUEL TUBE SUB-ASSEMBLY

a.
A165142E07
0.104,0.042 0.344,0.24 0.24,0.198 10 false *a 0.177,2.365 0.354,2.552 0.177,0.188 10 false *b

Remove the 2 bolts and separate the No. 2 fuel tube sub-assembly.

Text in Illustration
*a LH Side
*b RH Side


Hide 83520 16.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY (w/o Trailer Towing System)

Hide 17.REMOVE ENGINE OIL COOLER (w/ Trailer Towing System)

Hide 15671 18.REMOVE OIL FILTER BRACKET (w/o Trailer Towing System)

Hide 11452 19.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 27020 20.REMOVE GENERATOR ASSEMBLY

Hide 16261G 21.REMOVE NO. 1 WATER BY-PASS HOSE

a.
A308519

Slide the 2 clamps and remove the No. 1 water by-pass hose from the inlet water housing and front water by-pass joint.


Hide 17303 22.SEPARATE AIR PIPE SUB-ASSEMBLY

Hide 16206 23.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A162551

Slide the 2 clamps and disconnect the No. 2 water by-pass hose and No. 3 water by-pass hose from the water by-pass pipe sub-assembly.


b.

Remove the 2 bolts and water by-pass pipe sub-assembly.


Hide 16268 24.SEPARATE NO. 1 WATER BY-PASS PIPE

a.

Remove the 2 bolts and separate the No. 1 water by-pass pipe.


Hide 25.DISCONNECT NO. 9 WATER BY-PASS HOSE

a.
A291559E04
2.177,0.115 2.292,0.115 2.292,0.115 2.417,0.479 true 1.146,0.75 1.313,0.75 1.313,0.75 1.823,1.167 true 0.917,0.677 1.115,0.875 0.198,0.198 10 true *1 1.969,0.021 2.156,0.219 0.188,0.198 10 false *2

Slide the clamp and disconnect the No. 9 water by-pass hose from the front water by-pass joint.

Text in Illustration
*1 No. 9 Water By-pass Hose
*2 No. 10 Water By-pass Hose


Hide 26.DISCONNECT NO. 10 WATER BY-PASS HOSE

a.

Slide the clamp and disconnect the No. 10 water by-pass hose from the front water by-pass joint.


Hide 16355 27.REMOVE FRONT WATER BY-PASS JOINT

a.
A291566

Slide the clamp and disconnect the No. 2 water by-pass hose from the front water by-pass joint.


b.

Remove the 4 nuts, front water by-pass joint and 2 gaskets.


Hide 17303 30.REMOVE AIR PIPE SUB-ASSEMBLY

a.
A162553

Remove the bolt, disconnect the 2 hoses, and remove the air pipe sub-assembly.


Hide 16323 31.REMOVE INLET WATER HOUSING

Hide 16603 33.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.
A162557

Remove the bolt and No. 1 idler pulley sub-assembly.


Hide 16211 34.REMOVE FLUID COUPLING BRACKET

a.
A162558

Remove the 4 bolts and fluid coupling bracket.


Hide 16620 35.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A162527

Remove the standard bolt, 6 mm hexagon wrench bolt and V-ribbed belt tensioner assembly.


Hide 11202 37.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A162523

Remove the 14 bolts, seal washer, cylinder head cover sub-assembly LH and gasket.

HINT:

Make sure that the removed parts are returned to the same places they were removed from.



b.
A162524

Remove the 5 O-rings from the No. 2 camshaft bearing cap and No. 3 camshaft bearing cap.


Hide 11201 38.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A162525

Remove the 14 bolts, seal washer, cylinder head cover sub-assembly and gasket.

HINT:

Make sure that the removed parts are returned to the same places they were removed from.



b.
A162526

Remove the 5 O-rings from the No. 1 camshaft bearing cap and No. 3 camshaft bearing cap.


Hide 40.DISCONNECT WIRE HARNESS CLAMP BRACKET

a.
A163733

Remove the bolt and disconnect the wire harness clamp bracket.


Hide 11302 41.REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY

a.
A162529E02
1.826,0.549 2.068,0.719 0.242,0.170 10 *1

Remove the 28 bolts and nut shown in the illustration.

Text in Illustration
*1 Nut


b.
A162530

Remove the timing chain or belt cover sub-assembly by prying between it and the cylinder head and cylinder block with a screwdriver as shown in the illustration.

HINT:

Tape the screwdriver tip before use.


NOTICE:

Be careful not to damage the cylinder head and cylinder block contact surfaces of the timing chain or belt cover sub-assembly.



c.
A162531

Remove the oil pump gasket from the cylinder block.


d.
A164415

Remove the O-ring from the oil pan sub-assembly.


Hide 16322 42.REMOVE INLET WATER PIPE

a.
A162532

Remove the inlet water pipe from the No. 1 heat exchanger cover.


b.

Remove the 2 O-rings from the inlet water pipe.