Home › Engine / Hybrid System › 3UR-FE ENGINE MECHANICAL › CYLINDER HEAD › 2015.08–2016.10
RM27L0U _51 Engine / Hybrid System _049296 3UR-FE ENGINE MECHANICAL _0235562 CYLINDER HEAD G

3UR-FE ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 1.INSPECT CAMSHAFT OIL CLEARANCE

a.

Clean the bearing caps, camshaft housing and camshaft journals.


b.

Place the camshafts on the camshaft housing.


c.
A145569E01
0.49,0.093 1.180,0.294 0.690,0.202 10 Plastigage 1.344,0.207 1.725,0.664 false

Lay a strip of Plastigage across each of the camshaft journals.


d.

Install the camshaft bearing caps (See page Engine / Hybrid System>3UR-FE ENGINE MECHANICAL>CAMSHAFT>INSTALLATION).

NOTICE:

Do not turn the camshaft.



e.

Install the camshaft housing (See page Engine / Hybrid System>3UR-FE ENGINE MECHANICAL>CAMSHAFT>INSTALLATION).

NOTICE:

Do not turn the camshaft.



f.

Remove the camshaft bearing caps (See page Engine / Hybrid System>3UR-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL).


g.
A160675E01
0.359,0 1.062,0.211 0.702,0.211 10 Plastigage 1.207,0.092 1.317,0.092 1.317,0.092 1.594,0.573 false 1.279,2.309 2.162,2.492 0.883,0.184 10 No. 1 Journal 0.609,3.161 1.231,2.405 false 0.595,3.784 1.234,2.402 false 1.36,4.348 2.346,4.511 0.986,0.163 10 Other Journals 1.293,3.801 2.03,4.332 false 2.03,4.327 1.289,3.2 false 2.029,4.33 1.834,3.809 false 2.029,4.325 1.838,3.2 false 2.029,4.33 2.379,3.184 false 2.029,4.325 2.378,3.787 false 2.029,4.325 3.005,3.189 false 2.029,4.325 3.004,3.789 false

Measure the Plastigage at its widest point.

Standard Oil Clearance:
Item Specified Condition
No. 1 journal 0.030 to 0.065 mm (0.00118 to 0.00256 in.)
Other journal 0.025 to 0.062 mm (0.000984 to 0.00244 in.)


Maximum Oil Clearance:
Item Specified Condition
No. 1 journal 0.10 mm (0.00394 in.)
Other journal 0.09 mm (0.00354 in.)


If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the camshaft housing.


Hide 2.INSPECT CAMSHAFT THRUST CLEARANCE

a.

Install the camshafts.


b.
A160690

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.08 to 0.135 mm (0.00315 to 0.00531 in.)


Maximum thrust clearance:

0.15 mm (0.00591 in.)


If the thrust clearance is more than the maximum, replace the camshaft housing. If the thrust surface is damaged, replace the camshaft.


Hide 13711B 3.INSPECT COMPRESSION SPRING

HINT:

The shape of the inner compression spring determines whether the valve spring type described here is A or B.


a.
A101392

Using a vernier caliper, measure the free length of the inner compression spring.

Standard free length:
Type Specified Condition
Valve Spring Type A 49.69 to 53.19 mm (1.96 to 2.09 in.)
Valve Spring Type B 49.38 to 53.38 mm (1.94 to 2.10 in.)


If the free length is not as specified, replace the spring.


b.
A101393E02
0.681,0.055 1.302,0.227 0.621,0.172 10 Deviation

Valve Spring Type A:

i.

Using a steel square, measure the deviation of the inner compression spring.

Maximum deviation:

1.0 mm (0.0394 in.)


Maximum angle (reference):

2°


If the deviation is greater than the maximum, replace the spring.



c.
A319225E23
0.042,1.208 1.146,1.438 1.104,0.229 10 false 40 mm (1.57 in.) 2.323,0.396 2.969,0.604 0.646,0.208 10 false Deviation

Valve Spring Type B:

i.

Using a steel square, measure the deviation of the inner compression spring.

Maximum deviation:

1.0 mm (0.0394 in.)


Maximum angle (reference):

2°


If the deviation is greater than the maximum, replace the spring.



Hide 13711 4.INSPECT INTAKE VALVE

a.
A131997

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

5.470 to 5.485 mm (0.215 to 0.216 in.)


If the diameter is not as specified, replace the valve and guide bush.


b.
A131998E01
0.102,1.092 1.233,1.283 1.131,0.191 10 Margin Thickness

Using a vernier caliper, measure the valve head margin thickness.

Standard margin thickness:

1.10 to 1.40 mm (0.0433 to 0.0551 in.)


Minimum margin thickness:

0.50 mm (0.0197 in.)


If the margin thickness is less than the minimum, replace the intake valve.


c.
A131999E01
2.236,0.951 3.156,1.121 0.920,0.169 10 Overall Length

Using a vernier caliper, measure the valve's overall length.

Standard overall length:

105.85 mm (4.17 in.)


Minimum overall length:

105.35 mm (4.15 in.)


If the overall length is less than the minimum, replace the intake valve.


Hide 13715 5.INSPECT EXHAUST VALVE

a.
A132000

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

5.465 to 5.480 mm (0.215 to 0.216 in.)


If the diameter is not as specified, replace the valve and guide bush.


b.
A132001E01
0.059,1.146 1.199,1.330 1.139,0.185 10 Margin Thickness

Using a vernier caliper, measure the valve head margin thickness.

Standard margin thickness:

1.25 to 1.55 mm (0.0492 to 0.0610 in.)


Minimum margin thickness:

0.50 mm (0.0197 in.)


If the margin thickness is less than the minimum, replace the exhaust valve.


c.
A132002E01
2.275,0.997 3.250,1.171 0.975,0.173 10 Overall Length

Using a vernier caliper, measure the valve's overall length.

Standard overall length:

110.40 mm (4.35 in.)


Minimum overall length:

109.90 mm (4.33 in.)


If the overall length is less than the minimum, replace the exhaust valve.


Hide 6.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

A145559

a.

Using a caliper gauge, measure the inside diameter of the guide bush.

Standard bush inside diameter:

5.51 to 5.53 mm (0.217 to 0.218 in.)



b.

Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.

Standard Oil Clearance:
Item Specified Condition
Intake 0.025 to 0.060 mm (0.00098 to 0.00236 in.)
Exhaust 0.030 to 0.065 mm (0.00118 to 0.00256 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake 0.08 mm (0.00315 in.)
Exhaust 0.10 mm (0.00394 in.)


If the oil clearance is more than the maximum, replace the valve and guide bush.


Hide 11131 7.INSPECT INTAKE VALVE SEAT

A149128E01
0.807,1.074 1.223,1.223 0.416,0.149 10 Width

a.

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the valve seat.

HINT:

Do not rotate the valve while pressing the valve.



c.

Check the valve face and valve seat.

i.

Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.1 to 1.5 mm (0.0433 to 0.0591 in.).

If not, correct the valve seat.


ii.

Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.

If not, correct the valve seat.



Hide 11135 8.INSPECT EXHAUST VALVE SEAT

A149129E01
0.815,1.089 1.198,1.233 0.383,0.144 10 Width

a.

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the valve seat.

HINT:

Do not rotate the valve while pressing the valve.



c.

Check the valve face and valve seat.

i.

Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.1 to 1.5 mm (0.0433 to 0.0591 in.).

If not, correct the valve seat.


ii.

Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.

If not, correct the valve seat.



Hide 11101 9.INSPECT CYLINDER HEAD SUB-ASSEMBLY

A380011E01
3.854,0.188 7.156,0.427 3.302,0.24 10 false Cylinder Head Block Side: 3.844,1.75 5.667,1.979 1.823,0.229 10 false Intake Manifold Side: 3.833,2.813 5.656,3.042 1.823,0.229 10 false Exhaust Manifold Side:

a.

Using a precision straightedge and feeler gauge, measure the warpage of the surfaces where the cylinder head contacts the cylinder block and manifold.

Standard Warpage:
Item Specified Condition
Cylinder block side 0.05 mm (0.00197 in.)
Intake manifold side 0.08 mm (0.00315 in.)
Exhaust manifold side 0.05 mm (0.00197 in.)


Maximum warpage:

0.10 mm (0.00394 in.)


If the warpage is more than the maximum, replace the cylinder head.


b.
A145553

Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.

If cracked, replace the cylinder head.