11101A
1.INSPECT CYLINDER HEAD SET BOLT
Using a vernier caliper, measure the diameter of the elongated thread at the measuring point.
94 mm (3.70 in.) for intake side bolt
89 mm (3.50 in.) for exhaust side bolt
10.85 to 11.00 mm (0.427 to 0.433 in.)
10.6 mm (0.417 in.)
If the diameter is less than the minimum, replace the cylinder head bolt.
If a visual check reveals no excessively thin areas, check the center of the bolt (see illustration) and find the area that has the lowest diameter.
13801
2.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Turn the roller by hand to check that it turns smoothly.
If the roller does not turn smoothly, replace the valve rocker arm.
13750
3.INSPECT VALVE LASH ADJUSTER ASSEMBLY
Keep the adjuster free from dirt and foreign objects.
Use only clean engine oil.
Place the lash adjuster into a container full of new engine oil.
Insert SST's tip into the lash adjuster's plunger and use the tip to press down on the check ball inside the plunger.
Squeeze SST and the lash adjuster together to move the plunger up and down 5 to 6 times.
Check the movement of the plunger and bleed air.
Plunger moves up and down.
When bleeding high-pressure air from the compression chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.
After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with your fingers.
Plunger can be pressed 3 times.
If the plunger can still be compressed after pressing it 3 times, replace the lash adjuster with a new one.
4.INSPECT CAMSHAFT SUB-ASSEMBLY
Inspect the camshaft for runout.
Place the camshaft on V-blocks.
Using a dial indicator, measure the circle runout at the center journal.
0.04 mm (0.00157 in.)
If the circle runout is more than the maximum, replace the camshaft.
Check the oil clearance after replacing the camshaft.
Using a micrometer, measure the cam lobe height.
| Item | Specified Condition |
|---|---|
| Intake | 44.291 to 44.441 mm (1.744 to 1.750 in.) |
| Exhaust | 44.196 to 44.346 mm (1.740 to 1.746 in.) |
| Item | Specified Condition |
|---|---|
| Intake | 44.241 mm (1.742 in.) |
| Exhaust | 44.146 mm (1.738 in.) |
If the cam lobe height is less than the minimum, replace the camshaft.
Using a micrometer, measure the journal diameter.
| Item | Specified Condition |
|---|---|
| No. 1 journal | 29.956 to 29.970 mm (1.1793 to 1.1799 in.) |
| Other journal | 25.959 to 25.975 mm (1.0220 to 1.0226 in.) |
If the journal diameter is not as specified, check the oil clearance.
13050
5.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
13080
6.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
13506
7.INSPECT CHAIN SUB-ASSEMBLY
Using a spring scale, pull the chain with a force of 147 N (15 kgf, 33.1 lbf) as shown in the illustration.
Using a vernier caliper, measure the length of 15 pins.
136.9 mm (5.39 in.)
Perform the measurement at 3 random places.
If the elongation is more than the maximum, replace the chain.
13507
8.INSPECT NO. 2 CHAIN SUB-ASSEMBLY
Using a spring scale, pull the chain with a force of 147 N (15 kgf, 33.1 lbf) as shown in the illustration.
Using a vernier caliper, measure the length of 15 pins.
137.6 mm (5.42 in.)
Perform the measurement at 3 random places.
If the elongation is more than the maximum, replace the chain.
13521
9.INSPECT CRANKSHAFT TIMING GEAR OR SPROCKET
Wrap the chain around the sprocket.
Using a vernier caliper, measure the sprocket diameter with the chain.
61.4 mm (2.42 in.)
The vernier caliper must contact the chain rollers for the measurement.
If the diameter is less than the minimum, replace the chain and sprocket.
13522S
10.INSPECT CRANKSHAFT TIMING SPROCKET LH
Wrap the chain around the sprocket.
Using a vernier caliper, measure the sprocket diameter with the chain.
61.4 mm (2.42 in.)
The vernier caliper must contact the chain rollers for the measurement.
If the diameter is less than the minimum, replace the chain and sprocket.
13540
11.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY
Move the stopper plate upward to release the lock. Push the plunger and check that it moves smoothly.
If necessary, replace the chain tensioner.
13550
12.INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY
Check that the plunger moves smoothly.
Measure the worn depth of the chain tensioner.
0.9 mm (0.0354 in.)
If the depth is more than the maximum, replace the chain tensioner.
13560A
13.INSPECT NO. 3 CHAIN TENSIONER ASSEMBLY
Check that the plunger moves smoothly.
Measure the worn depth of the chain tensioner.
0.9 mm (0.0354 in.)
If the depth is more than the maximum, replace the chain tensioner.
13559
14.INSPECT CHAIN TENSIONER SLIPPER
for LH:
Measure the worn depth of the chain tensioner slipper.
1.0 mm (0.0394 in.)
If the depth is more than the maximum, replace the chain tensioner slipper.
for RH:
Measure the worn depth of the chain tensioner slipper.
1.0 mm (0.0394 in.)
If the depth is more than the maximum, replace the chain tensioner slipper.
13561
15.INSPECT NO. 1 CHAIN VIBRATION DAMPER
for LH:
Measure the worn depth of the chain vibration damper.
1.0 mm (0.0394 in.)
If the depth is more than the maximum, replace the chain vibration damper.
for RH:
Measure the worn depth of the chain vibration damper.
1.0 mm (0.0394 in.)
If the depth is more than the maximum, replace the chain vibration damper.
17105
16.INSPECT EXHAUST MANIFOLD SUB-ASSEMBLY LH
Using a precision straightedge and feeler gauge, measure the warpage of the contact surface of the cylinder head.
0.7 mm (0.0276 in.)
If the warpage is more than the maximum, replace the exhaust manifold.
17104
17.INSPECT EXHAUST MANIFOLD SUB-ASSEMBLY RH
Using a precision straightedge and feeler gauge, measure the warpage of the contact surface of the cylinder head.
0.7 mm (0.0276 in.)
If the warpage is more than the maximum, replace the exhaust manifold.