Home › Engine / Hybrid System › 3UR-FE FUEL › FUEL PUMP › 2015.08–2016.10
RM27L0U _51 Engine / Hybrid System _049298 3UR-FE FUEL _0235582 FUEL PUMP A

3UR-FE FUEL  FUEL PUMP  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the fuel pump (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the fuel pump (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


a.

Apply a light coat of gasoline to a new gasket, and install it to the fuel tank.


b.
A152236E03
2.344,1.469 2.625,1.229 true 2.625,1.229 2.698,1.229 false 2.302,0.625 1.719,0.146 true 1.719,0.146 1.615,0.146 false 0.875,0.042 1.573,0.24 0.698,0.198 10 false Protrusion 2.729,1.135 3.229,1.333 0.5,0.198 10 true Groove

Align the protrusion of the pump and gauge tube with the groove of the fuel tank.


c.

Install the fuel suction with pump and gauge tube into the fuel tank.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge.



d.

Put the retainer on the fuel tank. While holding the fuel suction with pump and gauge tube, tighten the retainer one complete turn by hand.


e.
A259584E03
2.813,0.219 2.656,0.219 2.656,0.219 2.417,0.479 false 2.844,0.135 3.167,0.344 0.323,0.208 10 true SST

Set SST on the retainer.

SST
09808-14030  

HINT:
·

Hold the fuel suction tube assembly upright by hand to ensure that the fuel suction tube gasket is not moved out of position.

·

Securely attach the claws of SST to the protrusions of the retainer and fix SST in place.

·

Install SST while pressing the claws of SST against the retainer (toward the center of SST).




f.
A259587E02
1.167,3.26 1.771,3.594 1.771,3.594 2.219,3.052 false 1.594,1.698 1.75,1.698 1.75,1.698 1.948,2.99 true 2.781,0.26 2.667,0.26 2.667,0.26 2.385,0.5 false 2.823,0.167 3.135,0.344 0.313,0.177 10 true SST 1.073,3.615 2.385,3.802 1.313,0.188 10 true Fuel Tank Side Mark 1.802,4.052 1.948,4.24 0.146,0.188 10 false A 0.365,1.604 1.625,1.833 1.26,0.229 10 true Retainer Side Mark

Using SST, tighten the retainer until the mark on the retainer is within range A on the fuel tank, as shown in the illustration.

SST
09808-14030  

HINT:

Fit the tips of SST onto the ribs of the retainer.



g.
A152247

Install the 2 fuel tank tubes with the 2 tube joint clips.

NOTICE:
A118171E23
2.448,0.229 2.292,0.229 2.292,0.229 2.083,0.542 false 0.344,0.094 0.125,0.094 0.125,0.094 0.969,0.875 false 0.969,1.177 0.708,1.365 0.708,1.365 0.979,1.333 false 1.604,1.052 1.719,1.052 1.719,1.052 2.198,1.417 false 2.5,0.146 3.177,0.302 0.677,0.156 10 false Fuel Tube 0.375,0.01 1.438,0.188 1.063,0.177 10 false Fuel Tube Joint 0.219,1.292 0.792,1.521 0.573,0.229 10 false O-Ring 2.25,1.323 3.271,1.521 1.021,0.198 10 false Tube Joint Clip 0.354,4.208 1.104,4.396 0.75,0.188 10 false CORRECT 2.031,4.208 2.917,4.396 0.885,0.188 10 false INCORRECT

·

Check that there are no scratches or foreign objects on the connecting parts.

·

Check that the fuel tube joints are inserted securely.

·

Check that the tube joint clips are on the collars of the fuel tube joints.

·

After installing the tube joint clips, check that the fuel tube joints have not been pulled off.




Hide 77100 2.INSTALL FUEL TANK ASSEMBLY

a.

Install the fuel tank assembly (See page Engine / Hybrid System>3UR-FE FUEL>FUEL TANK>INSTALLATION).