Home › Engine / Hybrid System › 3UR-FE FUEL › FUEL TANK
RM27L0U _51 Engine / Hybrid System _049298 3UR-FE FUEL _0235583 FUEL TANK A

3UR-FE FUEL  FUEL TANK  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCHARGE FUEL SYSTEM PRESSURE

Hide 77310A 3.REMOVE FUEL TANK CAP

Hide 77209D 4.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

A185647E01
2.543,2.252 3.156,2.428 0.613,0.176 10 Lifting Up 0.197,4.311 0.874,4.464 0.678,0.153 10 Connector 1.95,4.165 2.687,4.342 0.737,0.177 10 Nylon Tube 1.225,4.3 1.689,4.470 0.464,0.170 10 O-Ring 0.606,4.205 0.606,4.306 false 1.124,3.975 1.43,4.269 1.43,4.269 1.335,3.982 false 0.331,2.902 0.630,3.083 0.298,0.181 10 Pipe 2.39,4.041 2.39,4.142 false 0.246,3.632 0.288,3.023 false 1.073,3.112 1.630,3.265 0.556,0.153 10 Retainer 0.706,3.484 1.046,3.212 false

a.

Detach the lock claw by lifting up the cover, as shown in the illustration.


b.

Pinch and pull the main tube connector to disconnect the fuel tank main tube sub-assembly connector from the pipe.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.




Hide 77204A 5.DISCONNECT FUEL TANK RETURN TUBE

A185646E01
2.543,2.252 3.156,2.428 0.613,0.176 10 Lifting Up 0.197,4.311 0.875,4.464 0.678,0.153 10 Connector 1.95,4.165 2.687,4.342 0.737,0.177 10 Nylon Tube 1.225,4.3 1.689,4.470 0.464,0.170 10 O-Ring 0.606,4.205 0.606,4.306 false 1.124,3.975 1.43,4.269 1.43,4.269 1.335,3.982 false 0.331,2.902 0.630,3.083 0.298,0.181 10 Pipe 2.39,4.041 2.39,4.142 false 0.246,3.632 0.288,3.023 false 1.073,3.112 1.630,3.265 0.556,0.153 10 Retainer 0.706,3.484 1.046,3.212 false

a.

Detach the lock claw by lifting up the cover, as shown in the illustration.


b.

Pinch and pull the return tube connector to disconnect the fuel tank return tube connector from the pipe.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.




Hide 77100 6.REMOVE FUEL TANK ASSEMBLY

a.
A185648

Disconnect the fuel tank to filler pipe hose from the fuel tank assembly.


b.
A185649

Pull up the retainer and disconnect the vent line hose.


c.
A185650E03
0.604,4.146 0.604,4.24 false 1.125,3.917 1.427,4.208 1.427,4.208 1.333,3.917 false 2.385,3.979 2.385,4.083 false 0.25,3.573 0.292,2.958 false 0.708,3.427 1.042,3.146 false 1.219,0.313 1.833,0.49 0.615,0.177 10 false Lifting Up 0.198,4.25 0.875,4.406 0.677,0.156 10 false Connector 1.948,4.104 2.688,4.281 0.74,0.177 10 false Nylon Tube 1.229,4.24 1.698,4.406 0.469,0.167 10 false O-Ring 0.333,2.844 0.635,3.021 0.302,0.177 10 true Pipe 1.073,3.052 1.625,3.208 0.552,0.156 10 false Retainer

Detach the lock claw by lifting up the cover, as shown in the illustration.


d.

Disconnect the fuel tank breather tube from the fuel tank inlet pipe sub-assembly.


e.
A152248

Set a mission jack underneath the fuel tank assembly.


f.

Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.


g.

Slowly lower the mission jack slightly.

NOTICE:

Be careful not to cut the wirings.



h.
A185651

Disconnect the wire harness clamp from the fuel tank assembly.


i.

Disconnect the fuel pump connector and lower the mission jack.

NOTICE:
·

Before this procedure, check the connector for dirt, mud or other contamination.

·

Do not use any tools in this procedure.




Hide 77697 7.REMOVE NO. 1 FUEL TANK HEAT INSULATOR

A152249E01
2.809,2.367 3.093,2.547 0.284,0.180 10 Nut 2.935,1.639 2.935,2.362 false

a.

Remove the nut from the heat insulator.


b.

Using needle-nose pliers, remove the 4 clips shown in the illustration and then remove the No. 1 fuel tank heat insulator.


Hide 77020A 8.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY