Home › Engine / Hybrid System › 3UR-FBE INTAKE / EXHAUST › EXHAUST MANIFOLD
RM27L0U _51 Engine / Hybrid System _049302 3UR-FBE INTAKE / EXHAUST _0235609 EXHAUST MANIFOLD A

3UR-FBE INTAKE / EXHAUST  EXHAUST MANIFOLD  REMOVAL  


PROCEDURE

Hide 53736 2.REMOVE FRONT FENDER APRON SEAL RH

a.

Remove the 6 clips and fender apron seal.


Hide 53736A 3.REMOVE FRONT FENDER APRON SEAL REAR RH

a.

Remove the 5 clips and fender apron seal.


Hide 53737B 4.REMOVE FRONT FENDER APRON SEAL LH

a.

Remove the 6 clips and fender apron seal.


Hide 53739A 5.REMOVE FRONT FENDER APRON SEAL REAR LH

a.

Remove the 5 clips and fender apron seal.


Hide 11452 6.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 17450B 9.REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY

A184981

a.

Remove the 2 bolts from the center exhaust pipe.


b.

Remove the 2 bolts and 2 nuts from the front No. 2 exhaust pipe sub-assembly.


c.

Disconnect the front No. 3 exhaust pipe sub-assembly and from exhaust pipe support.


d.

Remove the 2 gaskets.


e.

Disconnect the air fuel ratio sensor connector.


f.

Disconnect the heated oxygen sensor connector.


g.
A184304

Remove the 3 nuts, No. 2 exhaust pipe sub-assembly and gasket.


Hide 17410 10.REMOVE FRONT EXHAUST PIPE ASSEMBLY

a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the heated oxygen sensor connector and 2 clamps.


c.
A184982

Remove the 2 bolts from the center exhaust pipe.


d.

Remove the 3 nuts, front exhaust pipe and 2 gaskets.


Hide 58156 11.REMOVE FRONT NO. 4 FLOOR HEAT INSULATOR

A184951

a.

Remove the 4 nuts and front No. 4 floor heat insulator.


Hide 58155 12.REMOVE FRONT NO. 3 FLOOR HEAT INSULATOR

A184950

a.

Remove the 4 nuts and front No. 3 floor heat insulator.


Hide 45203 13.REMOVE NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

a.
C155150E04
1.365,1.417 0.948,1.781 false 0.948,1.781 1.719,1.563 false 0.49,1.781 1.24,1.948 0.75,0.167 10 true Matchmark

Put matchmarks on the No. 2 steering intermediate shaft sub-assembly and steering intermediate shaft.


b.

Remove the bolt and disconnect the No. 2 steering intermediate shaft sub-assembly from the steering intermediate shaft.


c.
C155151E05
0.99,1.469 1.646,1.344 false 0.99,1.469 1.677,1.563 false 0.219,1.385 0.969,1.552 0.75,0.167 10 true Matchmark

Put matchmarks on the No. 2 steering intermediate shaft sub-assembly and the power steering gear.


d.

Remove the bolt and disconnect the No. 2 steering intermediate shaft sub-assembly from the power steering gear.


Hide 17168 14.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A162114

Remove the 3 bolts and No. 2 exhaust manifold heat insulator.


Hide 17105 15.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

a.
A162115

Remove the 10 nuts, exhaust manifold sub-assembly LH and 2 gaskets.


Hide 17167 16.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A162752

Remove the 3 bolts and No. 1 exhaust manifold heat insulator.


Hide 17104 17.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

a.
A162754

Remove the 10 nuts, exhaust manifold sub-assembly RH and 2 gaskets.