Home › Engine / Hybrid System › 3UR-FE INTAKE / EXHAUST › EXHAUST PIPE
RM27L0U _51 Engine / Hybrid System _049301 3UR-FE INTAKE / EXHAUST _0235605 EXHAUST PIPE A

3UR-FE INTAKE / EXHAUST  EXHAUST PIPE  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·

Wear protective gloves when removing the exhaust pipe.

·

The exhaust pipe is extremely hot immediately after the engine has stopped.

·

Confirm that the exhaust pipe has cooled down before removing it.



PROCEDURE

Hide 17430 1.REMOVE TAILPIPE ASSEMBLY

A184925

a.

Remove the bolt, clamp and gasket.


b.

Disconnect the tailpipe assembly from the exhaust pipe support.


Hide 17420 2.REMOVE CENTER EXHAUST PIPE ASSEMBLY

A184926

a.

Remove the 4 bolts.


b.

Disconnect the center exhaust pipe assembly from the 3 exhaust pipe supports.


c.

Remove the center exhaust pipe assembly from the front exhaust pipe assembly and front No. 3 exhaust pipe sub-assembly.


d.

Remove the 2 gaskets from the front exhaust pipe assembly and front No. 3 exhaust pipe sub-assembly.


Hide 89465 3.REMOVE HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)

Hide 89465 4.REMOVE HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)

Hide 17450B 5.REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY

A184927

a.

Remove the 2 bolts and 2 nuts.


b.

Disconnect the front No. 3 exhaust pipe sub-assembly from the exhaust pipe support.


c.

Remove the front No. 3 exhaust pipe sub-assembly from the front No. 2 exhaust pipe sub-assembly assembly.


d.

Disconnect the air fuel ratio sensor connector.


e.
A184928

Remove the 3 nuts, front No. 2 exhaust pipe sub-assembly and 2 gaskets from the exhaust manifold LH.


Hide 17410 6.REMOVE FRONT EXHAUST PIPE ASSEMBLY

a.

Disconnect the air fuel ratio sensor connector.


b.
A184929

Remove the 3 nuts, front exhaust pipe and gasket from the exhaust manifold RH.


Hide 89467B 7.REMOVE AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

Hide 89467B 8.REMOVE AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

Hide 18435A 9.REMOVE MONOLITHIC CONVERTER PROTECTOR (for Bank 1)

A184934

a.

Remove the 4 bolts and 4 nuts.


b.

Remove the 2 monolithic converter protectors.


c.

Remove the 2 LH converter protector stays and 2 No. 2 converter protector stays.


Hide 18436 10.REMOVE NO. 1 MONOLITHIC CONVERTER PROTECTOR (for Bank 1)

A184936

a.

Remove the 4 bolts and 4 nuts.


b.

Remove the 2 No. 1 monolithic converter protectors.


c.

Remove the 2 No. 2 converter protector stay and 2 No. 3 converter protector stay.


Hide 18435A 11.REMOVE MONOLITHIC CONVERTER PROTECTOR (for Bank 2)

A184930

a.

Remove the 4 bolts and 4 nuts.


b.

Remove the 2 monolithic converter protectors.


c.

Remove the 2 LH converter protector stays and 2 No. 2 converter protector stays.


Hide 18436 12.REMOVE NO. 1 MONOLITHIC CONVERTER PROTECTOR (for Bank 2)

A184932

a.

Remove the 4 bolts and 4 nuts.


b.

Remove the 2 No. 1 monolithic converter protectors.


c.

Remove the 2 No. 2 converter protector stays and 2 No. 3 converter protector stays.