Home › Engine / Hybrid System › 3UR-FBE COOLING › RADIATOR
RM27L0U _51 Engine / Hybrid System _049303 3UR-FBE COOLING _0235615 RADIATOR A

3UR-FBE COOLING  RADIATOR  INSTALLATION  


PROCEDURE

Hide 16572 1.INSTALL OUTLET RADIATOR HOSE

a.
A198569E03
1.167,1.563 1.385,1.115 1.385,1.115 1.49,1.115 false 0.083,1.552 0.323,1.844 0.24,0.292 10 false RH 2.688,1.604 3.26,1.792 0.573,0.188 10 true View (A) 0.802,0.906 1.021,1.083 0.219,0.177 10 true UP 1.302,1.781 1.615,1.927 0.313,0.146 10 true 60° 0.813,1.99 1.01,2.156 0.198,0.167 10 true (A) 1.51,1.031 1.823,1.177 0.313,0.146 10 false 15°

Install the outlet radiator hose into the radiator.

HINT:

Install the hose so that the direction of the hose clamp is as indicated in the illustration.



Hide 16400 2.INSTALL RADIATOR ASSEMBLY

a.
A151752

Set the radiator bracket hooks to the radiator support holes.


b.

Install the radiator with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 16561 3.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL (for LH Side)

a.
A183237

Install the No. 1 radiator to support seal with the 3 clips.


Hide 16561 4.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL (for RH Side)

a.
A183236

Install the No. 1 radiator to support seal with the 3 clips.


Hide 53294C 5.INSTALL RADIATOR SIDE DEFLECTOR LH

a.
A215584

Install the deflector with the 6 clips.


b.

Connect the wire harness clamp.


Hide 53293C 6.INSTALL RADIATOR SIDE DEFLECTOR RH

a.
A299468

Install the deflector with the 6 clips.


Hide 16711 7.INSTALL FAN SHROUD

a.
A151842

Install the fan pulley to the fan bracket.


b.

Place the shroud together with the coupling fan between the radiator and engine.

NOTICE:

Be careful not to damage the radiator core.



c.

Temporarily install the fluid coupling fan to the fan bracket with the 4 nuts. Tighten the nuts as much as possible by hand.


d.
A183238

Attach the shroud claws to the radiator as shown in the illustration.


e.

Install the shroud with the 2 bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


f.

Connect the reservoir hose to the upper radiator tank.


g.

Install the fan and generator V belt (See page Engine / Hybrid System>3UR-FBE ENGINE MECHANICAL>DRIVE BELT>INSTALLATION).


h.

Tighten the 4 nuts of the fluid coupling fan.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16571 8.INSTALL INLET RADIATOR HOSE

a.
A198570E02
2.656,0.313 2.938,0.313 2.938,0.313 2.896,0.417 false 1.302,0.031 1.5,0.271 0.198,0.24 10 true UP 1.167,0.656 1.417,0.938 0.25,0.281 10 false RH 3,0.688 3.219,0.927 0.219,0.24 10 false FR 1.979,0.344 2.188,0.563 0.208,0.219 10 true 90° 0.177,1.229 0.729,1.563 0.552,0.333 10 false View (B) 2.542,2.875 3.104,3.208 0.563,0.333 10 true View (C) 1.49,0.969 1.698,1.156 0.208,0.188 10 true (B) 2.677,0.969 2.896,1.146 0.219,0.177 10 true (C) 2.677,0 2.885,0.188 0.208,0.188 10 true UP 3.104,0.208 3.365,0.365 0.26,0.156 10 true 90° 2.396,0.219 2.656,0.375 0.26,0.156 10 false 45°

Install the inlet radiator hose.

HINT:

Install the hose so that the direction of the hose clamp is as indicated in the illustration.



Hide 16572 9.CONNECT OUTLET RADIATOR HOSE

a.
A183234E02
0.854,0.552 1.188,1.167 false 0.26,1.271 0.813,1.604 0.552,0.333 10 true View (D) 2.531,1.667 2.75,1.844 0.219,0.177 10 false (D) 2.104,1.344 2.323,1.5 0.219,0.156 10 false FR 2.354,0.354 2.865,0.667 0.51,0.313 10 true Stopper 2.01,0.885 2.354,1.031 0.344,0.146 10 false 90° 0.208,0.458 0.719,0.896 0.51,0.438 10 true Stopper

Connect the outlet radiator hose to the water inlet housing.


Hide 52119A 12.INSTALL FRONT BUMPER COVER ASSEMBLY

a.

Install the front bumper cover assembly (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>INSTALLATION).