Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM
RM27L0U _51 Engine / Hybrid System _049309 CRUISE CONTROL _0235639 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Brake Switch "A" Circuit  


DESCRIPTION

When the brake pedal is depressed, the stop light switch sends a signal to the ECM. When the ECM receives this signal, it cancels the cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is normally applied to terminal STP of the ECM through the STOP fuse and the stop light switch, and the ECM turns the cruise control off.

DTC No. DTC Detection Condition Trouble Area
P0571 Voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for 0.5 seconds. or more.
·

Stop light switch

·

Stop light switch circuit

·

ECM



WIRING DIAGRAM

E162936E03
6.151,4.179 6.491,4.324 0.340,0.145 10 ECM 5.839,4.089 6.123,4.237 0.284,0.149 10 A27 5.92,0.825 6.222,0.984 0.301,0.158 10 STP 5.932,1.494 6.261,1.648 0.329,0.154 10 ST1- 5.687,0.745 5.867,0.893 0.180,0.149 10 26 5.687,1.417 5.865,1.564 0.178,0.147 10 35 4.918,0.738 5.023,0.895 0.105,0.157 10 1 3.882,1.416 3.979,1.568 0.098,0.152 10 4 3.881,0.747 3.989,0.895 0.108,0.149 10 2 4.932,1.414 5.037,1.561 0.105,0.147 10 3 3.863,1.86 4.066,2.014 0.203,0.154 10 A4 3.905,2.042 5.014,2.216 1.109,0.173 10 Stop Light Switch 3.189,1.642 3.469,1.793 0.280,0.150 10 IGN 2.229,2.094 2.489,2.259 0.260,0.165 10 IG2 1.271,1.631 1.903,1.774 0.632,0.143 10 IG2 MAIN 1.495,3.322 1.828,3.465 0.333,0.144 10 AM2 2.21,3.084 2.543,3.227 0.333,0.144 10 AM2 3.012,3.079 3.262,3.229 0.251,0.151 10 IG2 0.664,3.722 1.143,3.907 0.479,0.185 10 Battery 0.535,1.54 0.937,1.691 0.401,0.151 10 STOP 0.567,2.463 0.867,2.606 0.299,0.144 10 ALT 2.26,3.701 3.194,3.876 0.934,0.175 10 Ignition Switch 2.067,3.561 2.361,3.707 0.294,0.146 10 H10 2.058,3.097 2.180,3.235 0.122,0.139 10 5 3.3,3.07 3.408,3.226 0.108,0.155 10 6

PROCEDURE

1.READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Cruise Control / Data List.


e.

Check the Data List for proper functioning of the stop light switch.

ECM (Cruise Control)
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stp Light SW M-CPU Stop light switch signal (Main CPU) / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-

OK:

Normal conditions listed above are displayed.


Result
Result Proceed to
NG A
OK (for 3UR-FE) B
OK (for 3UR-FBE) C



A

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - BATTERY)

B

C

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - BATTERY)
a.
U153958E02
0.51,2.188 0.719,2.344 0.208,0.156 10 false A4 0.177,0.167 2.521,0.479 2.344,0.313 10 false Front view of wire harness connector: (to Stop Light Switch)

Disconnect the A4 connector from the stop light switch.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A4-2 - Body ground Always 11 to 14 V
A4-4 - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the connector from the stop light switch.



OK

3.INSPECT STOP LIGHT SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STOP LIGHT SWITCH
a.
E146086E05
2.604,1.729 3.021,2.333 false 3,1.073 2.583,1.448 false 2.427,1.729 2.01,2.333 false 1.99,1.052 2.406,1.427 false 0.448,1.531 0.583,1.021 0.583,1.021 0.74,1.021 false 0.052,2.063 0.573,2.406 0.521,0.344 10 false Not Pushed 0.781,2.063 1.302,2.24 0.521,0.177 10 false Pushed 3,2.354 3.156,2.531 0.156,0.177 10 false 1 3.063,0.927 3.219,1.104 0.156,0.177 10 false 2 1.938,2.354 2.094,2.531 0.156,0.177 10 false 3 1.875,0.927 2.031,1.104 0.156,0.177 10 false 4 0.104,0.104 2.635,0.479 2.531,0.375 10 false Component without harness connected: (Stop Light Switch) 0.771,0.938 1.031,1.104 0.26,0.167 10 false Pin

Remove the stop light switch (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Switch pin not pushed Below 1 Ω
3 - 4 Switch pin not pushed 10 kΩ or higher
1 - 2 Switch pin pushed 10 kΩ or higher
3 - 4 Switch pin pushed Below 1 Ω



c.

Reinstall the stop light switch.



OK

4.CHECK ECM

NG

REPLACE STOP LIGHT SWITCH

4.CHECK ECM
a.
U154098E01
0.248,0.1 2.576,0.421 2.328,0.321 10 Front view of wire harness connector: (to ECM) 2.672,1.149 2.970,1.296 0.298,0.147 10 STP 0.443,1.18 0.791,1.327 0.348,0.147 10 ST1- 0.853,1.262 0.975,1.262 0.975,1.262 1.878,2.52 false 2.597,1.231 2.475,1.231 2.475,1.231 2.135,2.192 false 1.64,1.149 1.904,1.306 0.264,0.156 10 A27

Disconnect the A27 connector from the ECM.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A27-26 (STP) - Body ground Brake pedal is depressed 11 to 14 V
A27-26 (STP) - Body ground Brake pedal is released Below 1 V
A27-35 (ST1-) - Body ground Brake pedal is depressed Below 1 V
A27-35 (ST1-) - Body ground Brake pedal is released 11 to 14 V


Result Proceed to
NG A
OK (for 3UR-FE) B
OK (for 3UR-FBE) C


d.

Disconnect the ECM connector.



A

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH - ECM)

B

C