Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM
RM27L0U _51 Engine / Hybrid System _049309 CRUISE CONTROL _0235639 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the system to enter the self-diagnostic mode. If a malfunction is present, DTCs will be output.

HINT:

When a particular warning light remains blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in the relevant ECU is suspected.


WIRING DIAGRAM

E162795E02
5.662,0.942 5.942,1.101 0.280,0.160 10 A27 5.711,0.721 5.907,0.869 0.196,0.148 10 16 6.012,0.956 6.242,1.113 0.229,0.157 10 TC 6.221,3.003 6.579,3.166 0.358,0.162 10 ECM 0.349,2.97 0.646,3.110 0.297,0.140 10 H19 0.586,3.139 0.966,3.284 0.380,0.146 10 DLC3 0.964,0.928 1.188,1.090 0.224,0.162 10 TC 0.947,1.827 1.176,1.981 0.229,0.154 10 CG 3.922,1.956 4.972,2.125 1.049,0.169 10 to Other System 1.235,0.847 1.417,1.004 0.182,0.157 10 13 1.251,1.724 1.367,1.883 0.117,0.159 10 4

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - ECM)
a.

Disconnect the A27 connector from the ECM.


E337701E03
0.677,1.479 1.083,1.719 0.406,0.24 3.281,1.469 3.688,1.708 0.406,0.24 1.865,1.448 2.104,1.063 false 2.115,2.125 1.979,1.792 false 5.688,0.781 5.5,1.344 false 0.25,0.26 1.542,0.448 1.292,0.188 10 false Front view of DLC3: 0.76,1.521 1.083,1.688 0.323,0.167 10 false H19 2.135,0.906 2.458,1.073 0.323,0.167 10 false CG 2.01,2.146 2.333,2.313 0.323,0.167 10 false TC 3.833,0.135 6.135,0.51 2.302,0.375 10 false Front view of wire harness connector: (to ECM) 3.375,1.51 3.698,1.677 0.323,0.167 10 false A27 5.646,0.615 5.969,0.781 0.323,0.167 10 false TC

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-16 (TC) - H19-13 (TC) Always Below 1 Ω



c.

Reconnect the ECM connector.



OK

2.CHECK HARNESS AND CONNECTOR (TERMINAL CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (TERMINAL CG of DLC3 - BODY GROUND)
a.
U153408E01
1.697,0.419 1.996,0.575 0.299,0.156 10 H19 0.942,0.528 1.191,0.684 0.250,0.156 10 CG 1.603,1.037 1.345,0.607 1.345,0.607 1.253,0.607 false 0.047,0.054 1.325,0.196 1.278,0.142 10 Front view of DLC3:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-4 (CG) - Body ground Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - BODY GROUND)
a.
U153409E01
1.113,1.934 1.332,2.090 0.218,0.156 10 TC 1.734,0.456 2.039,0.612 0.305,0.156 10 H19 1.803,1.618 1.491,2.029 1.491,2.029 1.363,2.029 false 0.056,0.027 1.314,0.185 1.258,0.158 10 Front view of DLC3:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-13 (TC) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS, CONNECTOR, OR EACH ECU