Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC LASER CRUISE CONTROL SYSTEM
RM27L0U _51 Engine / Hybrid System _049309 CRUISE CONTROL _0235640 DYNAMIC LASER CRUISE CONTROL SYSTEM D

CRUISE CONTROL  DYNAMIC LASER CRUISE CONTROL SYSTEM  ROAD TEST  


PROBLEM SYMPTOM CONFIRMATION


HINT:

The dynamic laser cruise control system has two cruise control modes: the constant speed control mode and vehicle-to-vehicle distance control mode.

·

The vehicle-to-vehicle distance control mode is always selected when starting up the dynamic laser cruise control system.

·

Operation of the constant speed control mode is the same as that for a conventional cruise control system.



a.
E345243

Inspect the SET function.

i.

Turn the main switch on.


ii.

Drive at the required speed (45 km/h (27 mph) or higher).


iii.

Push the cruise control main switch to - (COAST)/SET.


iv.

After releasing the switch, check that the vehicle cruises at the set speed.



b.
E345244

Inspect the + (ACCEL) function.

i.

Turn the main switch on.


ii.

Drive at the required speed (45 km/h (27 mph) or higher).


iii.

Push the cruise control main switch to - (COAST)/SET.


iv.

Check that vehicle speed increases while the cruise control main switch is pushed to + (ACCEL)/RES (RESUME), and that the vehicle cruises at the newly set speed when the switch is released.


v.

Push the cruise control main switch to + (ACCEL)/RES (RESUME) and then release it immediately. Check that vehicle speed increases* (tap-up control).

HINT:

*: Constant speed control mode: increases by 1.6 km/h (1.0 mph); vehicle-to-vehicle distance control mode: increases by 5 km/h (5 mph).




c.
E345243

Inspect the - (COAST) function.

i.

Turn the main switch on.


ii.

Drive at the required speed (45 km/h (27 mph) or higher).


iii.

Push the cruise control main switch to - (COAST)/SET.


iv.

Check that vehicle speed decreases while the cruise control main switch is pushed to - (COAST)/SET, and that the vehicle cruises at the newly set speed when the switch is released.


v.

Push the cruise control main switch to - (COAST)/SET, and then release it immediately. Check that vehicle speed decreases* (tap-down control).

HINT:

*: Constant speed control mode: decreases by 1.6 km/h (1.0 mph); vehicle-to-vehicle distance control mode: decreases by 5 km/h (5 mph).




d.
E345245

Inspect the CANCEL function.

i.

Turn the main switch on.


ii.

Drive at the required speed (45 km/h (27 mph) or higher).


iii.

Push the cruise control main switch to - (COAST)/SET.


iv.

When performing any one of the following, check that the cruise control system is canceled and that the normal driving mode is reset.

·

Depressing the brake pedal

·

The shift lever is moved from D to N or the transmission is shifted to the 3rd, 2nd, or 1st gear with the shift lever in S.

·

Turning the main switch off (the stored vehicle speed in the ECM is not maintained.)

·

Pulling the cruise control main switch to CANCEL




e.
E345244

Inspect the RES (RESUME) function.

i.

Turn the main switch on.


ii.

Drive at the required speed (45 km/h (27 mph) or higher).


iii.

Push the cruise control main switch to - (COAST)/SET.


iv.

Cancel the cruise control system by performing any of the above operations (other than turning the main switch off).


v.

After pushing the cruise control main switch to + (ACCEL)/RES (RESUME) at a driving speed of more than 40 km/h (25 mph), check that the vehicle resumes the speed set prior to the cancellation.

HINT:

The stored vehicle speed is retained even if vehicle speed drops below 40 km/h (25 mph) once. The previously stored vehicle speed can be resumed by pushing the cruise control main switch to + (ACCEL)/RES (RESUME) when vehicle speed returned to approximately 40 km/h (25 mph) or more.