Home › Drivetrain › AB60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM27L0U _52 Drivetrain _049310 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0235644 AUTOMATIC TRANSMISSION SYSTEM D

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  DTC CHECK / CLEAR  


NOTICE:

When the diagnosis system is changed from normal mode to check mode or vice versa, all DTCs and freeze frame data recorded in normal mode are cleared. Before changing modes, always check and make a note of DTCs and freeze frame data.


HINT:
·

DTCs which are stored in the ECM can be displayed on the Techstream. The Techstream can display the current, pending and permanent DTCs.

·

If a malfunction is detected during the current driving cycle, current and permanent DTCs are stored.

·

Some DTCs are not stored if the ECM does not detect the same malfunction again during a second consecutive driving cycle. However, such malfunctions, detected on only one occasion, are stored as pending DTCs.

·

Current and pending DTCs can be cleared by using the Techstream or by disconnecting the cable from the negative battery terminal. However, permanent DTCs cannot be cleared using either of these two methods.

·

After clearing current DTCs using the Techstream (or by disconnecting the cable from the negative battery terminal), permanent DTCs can be cleared when the system is determined to be normal for the relevant DTCs and then the universal trip is performed.


2-trip Detection Examples
Pending DTC Store condition Malfunction detected
Clear condition System determined to be normal
or
DTCs cleared using Techstream
or
Cable disconnected from negative battery terminal
Current DTC Store condition Malfunction detected (2nd trip)
Clear condition No malfunctions in 40 driving cycles
or
DTCs cleared using Techstream
or
Cable disconnected from negative battery terminal
Permanent DTC Store condition Malfunction detected (2nd trip)
Clear condition Ignition switch turned to ON after no malfunction is detected in 3 consecutive driving cycles
or
After DTCs cleared using Techstream or cable disconnected from negative battery terminal, malfunction not detected when universal trip driving performed
MIL ON Malfunction detected (2nd trip)
OFF Ignition switch turned to ON after no malfunction is detected in 3 consecutive driving cycles
or
DTCs cleared using Techstream
or
Cable disconnected from negative battery terminal


A198847E53
0.052,0.083 1.813,0.26 1.76,0.177 10 false 2-trip Detection Example 0.052,1.125 0.333,1.323 0.281,0.198 10 false Trip 0.052,1.656 1.375,1.802 1.323,0.146 10 false Pending DTC Status 0.052,2.271 1.333,2.438 1.281,0.167 10 false Current DTC Status 0.052,2.958 0.792,3.125 0.74,0.167 10 false MIL Status 0.052,3.604 1.542,3.771 1.49,0.167 10 false Permanent DTC Status 1.531,0.385 1.917,0.573 0.385,0.188 10 false 1 Trip 2.365,0.385 2.75,0.573 0.385,0.188 10 false 2 Trip 3.208,0.385 3.594,0.573 0.385,0.188 10 false 3 Trip 4.052,0.385 4.438,0.573 0.385,0.188 10 false 4 Trip 4.896,0.385 5.281,0.573 0.385,0.188 10 false 5 Trip 5.729,0.385 6.115,0.573 0.385,0.188 10 false 6 Trip 6.542,0.375 7,0.563 0.458,0.188 10 false 43 Trip 0.708,1.021 1.156,1.198 0.448,0.177 10 false Driving 0.708,1.344 1.135,1.51 0.427,0.167 10 false IG off 0.354,4.104 1.823,4.292 1.469,0.188 10 false : Malfunction detected 0.354,4.427 2.042,4.615 1.688,0.188 10 false : Malfunction not detected 1.719,1.75 1.99,1.906 0.271,0.156 10 false ON 1.385,2.104 1.698,2.281 0.313,0.177 10 false OFF 2.573,2.396 2.844,2.552 0.271,0.156 10 false ON 2.24,2.729 2.552,2.906 0.313,0.177 10 false OFF 2.573,3.042 2.844,3.198 0.271,0.156 10 false ON 2.24,3.385 2.552,3.563 0.313,0.177 10 false OFF 2.573,3.708 2.844,3.865 0.271,0.156 10 false ON 2.24,4.052 2.552,4.229 0.313,0.177 10 false OFF

C211970E01
0.045,0.017 6.510,0.347 6.465,0.331 10 2-trip Detection Example (Instance when DTCs were cleared midway through by using the Techstream or by disconnecting the cable from the negative battery terminal) 0.045,1.929 0.326,2.123 0.281,0.194 10 Trip 0.045,2.6 1.361,2.769 1.316,0.170 10 Pending DTC Status 0.045,3.23 1.317,3.400 1.272,0.170 10 Current DTC Status 0.045,3.888 0.761,4.058 0.716,0.170 10 MIL Status 0.045,4.54 1.539,4.710 1.494,0.170 10 Permanent DTC Status 2.045,1.361 2.432,1.535 0.387,0.174 10 1 Trip 3.005,1.361 3.393,1.535 0.387,0.174 10 2 Trip 3.97,1.361 4.357,1.535 0.387,0.174 10 3 Trip 4.946,1.361 5.334,1.535 0.387,0.174 10 4 Trip 1.111,1.927 1.573,2.101 0.461,0.174 10 Driving 1.111,2.268 1.573,2.442 0.461,0.174 10 IG off 0.349,6.29 1.940,6.455 1.591,0.165 10 : Universal trip performed 5.656,0.948 6.636,1.293 0.980,0.345 10 Universal Trip Driving Pattern 2.227,2.681 2.494,2.836 0.267,0.156 10 ON 1.9,3.024 2.212,3.176 0.312,0.152 10 OFF 3.206,3.31 3.473,3.466 0.267,0.156 10 ON 2.88,3.653 3.192,3.806 0.312,0.152 10 OFF 3.206,3.97 3.473,4.125 0.267,0.156 10 ON 2.88,4.313 3.192,4.465 0.312,0.152 10 OFF 3.206,4.635 3.473,4.791 0.267,0.156 10 ON 2.88,4.978 3.192,5.131 0.312,0.152 10 OFF 0.349,5.273 1.764,5.452 1.415,0.179 10 : Malfunction detected 0.349,5.613 4.885,5.776 4.536,0.163 10 : After problem areas repaired and DTCs cleared, DTC check performed 0.349,5.949 2.028,6.119 1.679,0.170 10 : Malfunction not detected

CHECK DTC


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Check the DTC(s) and freeze frame data, and then write them down.




CLEAR DTC (Pending and Current DTC)


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Clear the DTCs.



CLEAR DTC (Pending and Current DTC without using Techstream)


a.

Perform either of the following operations:

i.

Disconnect the cable from the negative (-) battery terminal for more than 1 minute.


ii.

Remove the EFI NO. 1 and ETCS fuses from the engine room relay block located inside the engine compartment for more than 1 minute.




CLEAR PERMANENT DTC


HINT:

Even if the following procedure is not performed, permanent DTCs are cleared if no malfunction is detected during 3 consecutive driving cycles.


A198849E12
0.046,0.013 1.966,0.210 1.920,0.198 10 Universal Trip Driving Pattern 0.518,1.116 1.646,1.272 1.128,0.156 10 40 km/h (25 mph) 1.238,2.314 1.637,2.504 0.399,0.191 10 Idling 0.43,2.621 1.606,2.801 1.176,0.180 10 Ignition Switch ON 0.43,2.912 1.606,3.092 1.176,0.180 10 Ignition Switch Off 2.091,2.682 3.379,2.852 1.288,0.170 10 30 seconds or more 3.296,3.164 4.536,3.334 1.239,0.170 10 10 minutes or more 4.967,3.379 6.394,3.548 1.427,0.170 10 Permanent DTC Clear 3.284,0.438 4.945,0.608 1.661,0.170 10 Total of 5 minutes or more

a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Check if permanent DTCs are stored.

HINT:

If permanent DTCs are not output, it is not necessary to continue this procedure.



f.

Clear DTCs.


g.

Perform the universal trip.

1.

Idle the engine for 30 seconds or more.

2.

Drive the vehicle at 40 km/h (25 mph) or more for a total of 5 minutes or more.

HINT:
·

It is possible to complete the drive pattern even if the vehicle decelerates to less than 40 km/h (25 mph) during the driving cycle provided that the vehicle is driven at 40 km/h (25 mph) or more for a total of 5 minutes.

·

When accelerating through the gears, make sure the vehicle is driven so that all gears are used in order and no gears are skipped.



3.

Allow 10 minutes or more to elapse from the time the engine is started.



h.

Turn the ignition switch off.


i.

Wait 15 seconds.


j.

Turn the ignition switch to ON.


k.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


l.

Check that the permanent DTCs have been cleared.

HINT:
·

If the permanent DTCs have not been cleared, perform the universal trip again.

·

The permanent DTCs are cleared when the universal trip is completed.