Home › Drivetrain › AB60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM27L0U _52 Drivetrain _049311 AB60E AUTOMATIC TRANSMISSION / TRANSAXLE _0235670 AUTOMATIC TRANSMISSION SYSTEM C

AB60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0729  Gear 6 Incorrect Ratio  


DESCRIPTION

The ECM uses signals from the output speed sensor SP2 and input speed sensor NT to detect the actual gear position (1st, 2nd, 3rd, 4th, 5th or 6th gear). Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).

DTC Code DTC Detection Condition Trouble Area
P0729

6th gearshift malfunction:

The ECM determines there is a malfunction when both of the following conditions are met. (2-trip detection logic)


(a) When the ECM directs the transmission to switch to 5th gear, the actual gear is also shifted to 5th.
(b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 4th.
·

Valve body is blocked up or stuck (sequence valve)

·

Shift solenoid valve SLT remains open or closed

·

Automatic transmission (clutch, brake or gear, etc.)



HINT:
·

Gear positions in the event of a solenoid valve mechanical problem:

ECM command gearshift 1st 2nd 3rd 4th 5th 6th
Actual gear position under malfunction 1st 2nd 3rd 4th 5th 4th

·

Gear position during fail-safe operation:

If any malfunction is detected, the ECM changes into the fail-safe mode to shift into the gear positions as shown in the table below.

Gear position under normal conditions 1st 2nd 3rd 4th 5th 6th
Actual gear position under fail-safe mode 1st 2nd 3rd 3rd 3rd 3rd



MONITOR DESCRIPTION

The ECM commands gear shifts by turning the shift solenoid valves "ON/OFF" and switching oil pressure to the valves in the valve body.

The DTC indicates that the sequence valve is locked in the direction the spring stretches and that shifting to 6th gear is impossible.

MONITOR STRATEGY

Related DTCs P0729: Gear 6 incorrect ratio (Sequence valve)/Functional check
Required sensors/Components Sequence valve
Frequency of operation Continuous
Duration 0.4 seconds
MIL operation 2 driving cycles
Sequence of operation None

TYPICAL ENABLING CONDITIONS

All
The monitor will run whenever the following DTCs are not present P0717 (Turbine speed sensor circuit)
P0722 (Output speed sensor circuit)
P0973, P0974 (Shift solenoid valve S1 circuit)
P0976, P0977 (Shift solenoid valve S2 circuit)
P0979, P0980 (Shift solenoid valve S3 circuit)
P0982, P0983 (Shift solenoid valve S4 circuit)
P0985, P0986 (Shift solenoid valve SR circuit)
P0748 (Shift solenoid valve SL1 circuit)
P0778 (Shift solenoid valve SL2 circuit)
P0115, P0116, P0117, P0118, P011B (ECT (Engine coolant temperature) sensor circuit)
P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D (KCS sensor circuit)
ETCS (Electric Throttle Control System) Not system down
Transmission position "D"
Duration time from shifting "N" to "D" 4 seconds or more
ECT 40°C (104°F) or higher
Spark advance from max. retard timing by KCS control 0° crankshaft angle or more
Engine Starting
Calculated load value 7.75% or more (A/C off)
7.75% or more (A/C on)
Input speed/output speed (NT/NO)
NT: Input (Turbine) speed
NO: Internal counter shaft speed
3.11 to 7.58
or
1.83 to 2.27
or
1.24 to 1.49
or
0.93 to 1.07
or
0.66 to 0.80
or
0.51 to 0.65

Condition (A)
ECM selected gear 5th
Vehicle speed 2 km/h (1.2 mph) or more
Throttle valve opening angle 9% or more at 2000 rpm
(Conditions vary with engine speed)

Condition (B)
ECM selected gear 6th
Vehicle speed 2 km/h (1.2 mph) or more
Throttle valve opening angle 9% or more at 2000 rpm
(Conditions vary with engine speed)

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met: Condition (A) and (B)

Condition (A)
Turbine speed/Output speed (NT/NO) 0.66 or more, and 0.80 or less
(This means actual gear is 5th)

Condition (B)
Turbine speed/Output speed (NT/NO) 0.93 or more, and 1.07 or less
(This means actual gear is 4th)

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>AB60E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0729)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs using the Techstream.

Result
Result Proceed to
Only P0729 is output A
P0729 and other DTCs are output B

HINT:

If any other codes besides P0729 are output, perform troubleshooting for those DTCs first.




A

2.PERFORM ACTIVE TEST USING TECHSTREAM (RUNNING TEST)

B

2.PERFORM ACTIVE TEST USING TECHSTREAM (RUNNING TEST)
HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the Techstream, perform the Active Test.

HINT:

While driving, the shift position can be forcibly changed with the Techstream.


Engine and ECT
Tester Display Test Part Control Range Diagnostic Note
Control the Shift Position Operate shift solenoid valve and set each shift position by yourself
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Possible to check operation of shift solenoid valves
[Vehicle Condition]
50 km/h (30 mph) or less

HINT:
·

This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.

·

The 4th to 5th and 5th to 6th up-shift must be performed with the accelerator pedal released.

·

The 6th to 5th and 5th to 4th down-shift must be performed with the accelerator pedal released.

·

Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.

·

The shift position commanded by the ECM is shown in the Data List display on the Techstream.

·

Gear positions in the event of a solenoid valve mechanical problem:

Tester command gearshift 1st 2nd 3rd 4th 5th 6th
Actual gear position under malfunction 1st 2nd 3rd 4th 5th 4th



OK:

Gear position changes in accordance with the tester command.




OK

3.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT)

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

3.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT)
NOTICE:
·

Perform the test at the normal operating ATF temperature: 50 to 80°C (122 to 176°F).

·

Be careful to prevent SST hose from interfering with the exhaust pipe.

·

Perform the test with the A/C OFF.



HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.
C177721E04
1.552,3.76 1.104,4.156 1.104,4.156 1.042,4.156 true 0.563,0.615 0.667,0.74 false 2.958,2.031 2.917,1.854 false 2.875,2.042 3.167,2.188 0.292,0.146 10 false SST 0.417,4.031 1.083,4.219 0.667,0.188 10 false Test Plug 0.292,0.5 0.594,0.646 0.302,0.146 10 false SST

Remove the test plug on the transmission case center right side and connect SST.


SST
09993-19015  (09993-00010, 09993-00040)

b.

Connect the Techstream to the DLC3.


c.

Start the engine and warm it up.


d.

Measure the line pressure with SST.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the Techstream, perform the Active Test.


h.

Measure the line pressure.

Engine and ECT
Tester Display Test Part Control Range Diagnostic Note
Activate the Solenoid (SLT)* Operate the shift solenoid SLT and raise line pressure ON or OFF
HINT:
·

OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)

·

ON: No action (normal operation)



[Vehicle Condition]
·

Vehicle stopped

·

Engine idling



HINT:

*: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (See page Drivetrain>AB60E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>HYDRAULIC TEST) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.


OK:

The line pressure changes as specified when performing the Active Test.




OK

4.CLEAR DTC AND PERFORM RUNNING TEST

NG

4.CLEAR DTC AND PERFORM RUNNING TEST

OK

END

NG

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY