Home › Drivetrain › AB60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY
RM27L0U _52 Drivetrain _049311 AB60E AUTOMATIC TRANSMISSION / TRANSAXLE _0235666 AUTOMATIC TRANSMISSION ASSEMBLY A

AB60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.DRAIN AUTOMATIC TRANSMISSION FLUID

a.

Remove the drain plug and gasket, and drain ATF.


b.

Install a new gasket and the drain plug.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 37110 3.REMOVE PROPELLER SHAFT ASSEMBLY

Hide 17410 4.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 5.REMOVE FRONT NO. 3 EXHAUST PIPE ASSEMBLY

Hide 33820B 7.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

C155905

a.

Remove the nut and clip, and disconnect the transmission control cable.


Hide 28100 8.REMOVE STARTER ASSEMBLY

a.

Remove the starter assembly (See page Engine / Hybrid System>3UR-FE STARTING>STARTER>REMOVAL).


Hide 32101A 9.REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT

a.
C161354

Turn the crankshaft to gain access to the 6 bolts and remove the bolts while holding the crankshaft pulley setting bolt with a wrench.


Hide 35000 10.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

a.
C161355

Support the automatic transmission with a transmission jack. Lift the automatic transmission slightly from the crossmember.

NOTICE:

Position the jack so that it supports the oil pan bolt section, to prevent damage to the oil pan gasket.



Hide 51204 11.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
C161357

Remove the 4 bolts of the rear No. 1 engine mounting insulator.


b.
C161358

Remove the 4 nuts, 4 washers, 4 bolts and No. 3 frame crossmember.


Hide 12371 12.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

a.
C161359

Remove the 4 bolts and rear No. 1 engine mounting insulator from the automatic transmission.


Hide 13.DISCONNECT WIRE HARNESS AND CONNECTOR

a.
C155915

Remove the bolt and disconnect the ground cable.


b.
U152337

Tilt the automatic transmission downward.

NOTICE:

Make sure the cooling fan does not contact the fan shroud.



c.
C353007

Disconnect the park/neutral position switch connector, 2 transmission wire connectors and 2 speed sensor connectors.

HINT:

Detach the claw, press down the lever, and then disconnect the transmission wire connector.



d.

Disconnect the 3 connector clamps and 4 harness clamps.


e.

Remove the 2 bolts and disconnect the harness clamps and wire harness.


Hide 35104V 14.DISCONNECT BREATHER PLUG HOSE

a.
C163095

Disconnect the breather plug hose from the harness clamp bracket.


Hide 35000 15.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

a.
C161363

Remove the 10 bolts and automatic transmission.

NOTICE:

Do not use excess force when prying the automatic transmission.



Hide 16.REMOVE CONNECTOR CLAMP BRACKET

a.

Remove the 3 bolts and 3 oxygen sensor connector clamp brackets from the automatic transmission.


Hide 33823A 17.REMOVE TRANSMISSION CONTROL CABLE BRACKET

C161368

a.

Remove the 2 bolts and transmission control cable bracket.


Hide 32000 18.REMOVE TORQUE CONVERTER ASSEMBLY

a.

Remove the torque converter clutch from the automatic transmission.


Hide 19.INSPECT TORQUE CONVERTER CLUTCH AND DRIVE PLATE

a.