Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY(for 2WD)
RM27L0U _52 Drivetrain _049313 DRIVE SHAFT / PROPELLER SHAFT _0235685 PROPELLER SHAFT ASSEMBLY(for 2WD) A

DRIVE SHAFT / PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY(for 2WD)  REASSEMBLY  


PROCEDURE

Hide 04371H 1.INSTALL REAR PROPELLER SHAFT UNIVERSAL J0INT SPIDER

HINT:

Use the same installation procedure for both the front and rear propeller shaft universal joint spiders.


a.
C134387

Apply MP grease to a new universal joint spider and universal joint spider bearings.

NOTICE:

Be careful not to apply too much grease.



b.
C160084E01
1.24,0.979 1.373,1.116 0.133,0.137 10 A 1.695,0.979 1.809,1.128 0.114,0.149 10 B

Measure dimension A between the snap ring grooves.


c.

Install the universal joint spider bearing into the universal joint spider and measure dimension B.

HINT:

When measuring dimension B, clamp the universal joint spider and universal joint spider bearing in a vise to hold them together.



d.
G038874

Select hole snap rings of the correct thickness to make dimensions A and B the same.

Hole Snap Ring Thickness:
Color Thickness
Purple 1.46 mm (0.0574 in.)
Black 1.49 mm (0.0586 in.)
Copper 1.51 mm (0.0594 in.)
Black 1.52 mm (0.0598 in.)
Black 1.54 mm (0.0606 in.)
White 1.56 mm (0.0614 in.)
Black 1.57 mm (0.0618 in.)
Yellow 1.59 mm (0.0625 in.)
Black 1.62 mm (0.0638 in.)
Blue 1.64 mm (0.0646 in.)


NOTICE:
·

Use new hole snap rings.

·

If possible, use hole snap rings of the same thickness for both edges.




e.

Temporarily install the universal joint spider and 2 universal joint spider bearings into the universal joint sleeve yoke.


f.
U153594E01
1.239,1.582 0.652,2.16 0.652,2.16 1.761,2.055 false 0.652,2.16 1.389,3.111 false 0.299,2.065 0.643,2.306 0.343,0.241 10 SST

Using SST, press the universal joint spider bearing into the universal joint sleeve yoke until the groove can be seen.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04020, 09955-04051, 09957-04010)
09950-60010  (09951-00290)
09336-16010  

NOTICE:

Confirm that the universal joint spider moves smoothly while pressing it in.



g.
U153595

Using needle-nose pliers, install a hole snap ring into the groove on the universal joint sleeve yoke.

HINT:

Use the same installation procedure for the universal joint spider bearing on the opposite side.



h.

Temporarily install the universal joint spider and 2 universal joint spider bearings into the propeller shaft's universal joint yoke.


i.
U153598E01
1.488,1.854 1.523,1.854 false 2.128,1.854 2.109,1.854 false 0.852,3.071 0.849,3.129 false 0.842,3.056 0.59,2.946 false 0.861,3.055 0.949,3.016 false 1.143,2.93 1.116,2.942 false 1.864,1.349 2.574,1.14 2.574,1.14 2.293,1.029 false 2.603,1.057 2.953,1.292 0.350,0.235 10 SST 1.568,2.908 1.919,3.142 0.350,0.235 10 SST 0.904,2.988 1.546,2.991 false

Using SST, press the universal joint spider bearing into the universal joint yoke until the groove can be seen.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04020, 09955-04051, 09957-04010)
09950-60010  (09951-00290)
09336-16010  

NOTICE:
·

Position SST (09336-16010) so that the cutout faces the propeller shaft tube.

·

Confirm that the universal joint spider moves smoothly while pressing it in.




j.
U153593

Using needle-nose pliers, install a hole snap ring into the groove on the universal joint yoke.

HINT:

Use the same installation procedure for the universal joint spider bearing on the opposite side.