Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY(for 4WD)
RM27L0U _52 Drivetrain _049314 AXLE AND DIFFERENTIAL _0235691 FRONT DIFFERENTIAL CARRIER ASSEMBLY(for 4WD) A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL CARRIER ASSEMBLY(for 4WD)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STRAIGHT PIN

a.

Using a plastic-faced hammer, tap in the straight pins until their protrusion amounts are at the specified values shown in the illustration below.

C159431E02
1.292,0.615 1.458,0.802 0.167,0.188 10 true A 2.01,1.563 2.198,1.771 0.188,0.208 10 true A 2.396,3.177 2.542,3.333 0.146,0.156 10 false B 0.719,2.104 0.865,2.26 0.146,0.156 10 false A 2.417,4.51 2.563,4.667 0.146,0.156 10 false B 3.542,0.51 3.75,0.698 0.208,0.188 10 false *a 3.552,2.719 3.771,2.906 0.219,0.188 10 false *b 4.156,1.333 4.281,1.521 0.125,0.188 10 false a 4.26,0.656 4.385,0.844 0.125,0.188 10 false b 5.573,1.208 5.698,1.396 0.125,0.188 10 false c 4.188,3.531 4.313,3.719 0.125,0.188 10 false a 4.292,2.854 4.417,3.042 0.125,0.188 10 false b 5.552,3.385 5.677,3.573 0.125,0.188 10 false c 2.604,2.792 2.75,2.948 0.146,0.156 10 false A

Standard depth:
Item a b c
for Straight Pin A 19.5 to 20.5 mm
(0.768 to 0.807 in.)
9.991 to 10.000 mm
(0.3934 to 0.3937 in.)
9.5 to 10.0 mm
(0.375 to 0.397 in.)
for Straight Pin B 15.6 to 15.8 mm
(0.615 to 0.622 in.)
3.995 to 4.000 mm
(0.1573 to 0.1574 in.)
5.6 to 6.2 mm
(0.221 to 0.244 in.)


Text in Illustration
*a for Straight Pin A *b for Straight Pin B


Hide 41311A 2.INSTALL FRONT DIFFERENTIAL SIDE GEAR SHAFT RH BEARING

a.
C353021E01
1.844,0.865 2.271,0.865 false 2.323,0.792 2.781,0.99 0.458,0.198 10 false SST

Using SST and a press, press in the bearing.

SST
09223-00010  


b.
C159249

Using a snap ring expander, install a new snap ring.


Hide 41304F 3.INSTALL DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH

a.
C159248

Install the side gear shaft into the differential tube.


b.

Using snap ring pliers, install a new snap ring.


Hide 41304P 4.INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

a.
C159268E01
2.236,0.88 2.563,1.207 false 2.597,1.257 2.969,1.424 0.372,0.167 10 SST

Using SST and a plastic-faced hammer, tap in a new oil seal.

SST
09608-32010  

Standard oil seal depth:

4.8 to 5.8 mm (0.189 to 0.228 in.)



b.

Coat the lip of the oil seal with MP grease.


Hide 41434 5.INSTALL DIFFERENTIAL CLUTCH HUB

a.
C159253

Install the clutch hub onto the side gear inter shaft.


b.
C159252

Using snap ring pliers, install a new snap ring.

NOTICE:

Be sure to install the differential clutch hub in the correct direction.



Hide 41331G 6.INSTALL FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING

a.
C160137E03
1.042,0.792 0.74,0.552 false 0.458,0.427 0.781,0.573 0.323,0.146 10 false SST

Using SST and a press, press in 2 new bearings.

SST
09950-60010  (09951-00420)

Standard bearing depth:

1.2 to 1.8 mm (0.0473 to 0.0708 in.)



Hide 41311 7.INSTALL FRONT DIFFERENTIAL CASE

a.
FA01121

Install the 2 side gear thrust washers onto the 2 side gears.

HINT:

Using the table below, select the thrust washer which will ensure that the backlash is within the specifications.


Washer Thickness:
Thickness Thickness
1.43 to 1.47 mm (0.0563 to 0.0578 in.) 1.68 to 1.72 mm (0.0662 to 0.0677 in.)
1.48 to 1.52 mm (0.0583 to 0.0598 in.) 1.73 to 1.77 mm (0.0682 to 0.0696 in.)
1.53 to 1.57 mm (0.0603 to 0.0618 in.) 1.78 to 1.82 mm (0.0701 to 0.0717 in.)
1.58 to 1.62 mm (0.0623 to 0.0637 in.) 1.83 to 1.87 mm (0.0721 to 0.0736 in.)
1.63 to 1.67 mm (0.0642 to 0.0657 in.) -



b.

Install the 2 side gears, 2 side gear thrust washers, 2 pinion gears, 2 pinion gear thrust washers and pinion shaft into the differential case assembly.

HINT:
·

Align the holes of the differential case assembly and pinion shaft.

·

Apply hypoid gear oil to each sliding surface and rotating part.




c.

Measure the side gear backlash.

i.
F043636

Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the differential case assembly.

Standard backlash:

0.10 to 0.25 mm (0.00394 to 0.00984 in.)


If the backlash is not within the specification, install a side gear thrust washer with a different thickness.



d.
FA01124

Using a pin punch and hammer, tap in the straight pin through the differential case and hole of the pinion shaft.


e.

Stake the differential case.


Hide 8.INSTALL DIFFERENTIAL RING GEAR

a.

Clean the contact surfaces of the differential case and ring gear.


b.

Heat the ring gear to about 100°C (212°F) in boiling water.


c.

Carefully take the ring gear out of the boiling water.


d.

After the moisture on the ring gear has completely evaporated, quickly set the ring gear onto the differential case.

HINT:
·

Align the matchmarks on the ring gear and differential case.

·

Temporarily install the 10 bolts so that the bolt holes in the ring gear and differential case are aligned.




e.

After the ring gear cools down sufficiently, apply adhesive to the bolts and install them.

Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)

Adhesive:

Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent



Hide 41311A 9.INSTALL FRONT DIFFERENTIAL CASE BEARING

a.
C159256E01
0.955,1.008 0.663,1.109 0.663,1.109 0.958,1.343 false 0.292,1.011 0.591,1.204 0.299,0.193 10 SST

Using SST and a press, press in the 2 bearings (inner race).

SST
09316-20011  
09316-60011  (09316-00041)


Hide 41311A 10.INSTALL FRONT DIFFERENTIAL CASE BEARING

HINT:

When replacing the 2 differential case bearings, fit the thinnest washer to each bearing. When reusing the bearings, fit a washer of the same thickness as the one removed to each bearing.


a.
U152226E01
1.281,0.771 0.833,0.677 0.833,0.677 1.125,1.208 false 0.542,0.573 0.917,0.771 0.375,0.198 10 false SST 2.042,0.115 2.24,0.271 0.198,0.156 10 false *1

Install a new plate washer to the side bearing retainer.

Text in Illustration
*1 Plate Washer


b.

Using SST and a press, install the bearing (outer race) onto the differential case bearing retainer.

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)


c.
C159271E03
0.99,1.135 1.448,0.719 1.448,0.719 1.073,1.458 false 2.448,0.813 1.865,0.188 1.865,0.188 1.792,0.188 false 1.469,0.594 1.844,0.792 0.375,0.198 10 false SST 1.615,0.104 1.802,0.26 0.188,0.156 10 false *1

Install a new plate washer onto the differential carrier.

Text in Illustration
*1 Plate Washer


d.

Using SST and a press, press in the bearing (outer race) onto the differential carrier assembly.

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)


Hide 41211B 11.INSTALL FRONT DRIVE PINION FRONT RADIAL BALL BEARING

a.
C159339E01
1.158,2.179 0.941,1.968 0.941,1.968 1.729,2.179 false 0.549,1.88 0.883,2.045 0.334,0.165 10 SST

Using SST, install the bearing (outer race).

SST
09950-60020  (09951-00810, 09951-00890)


Hide 41211A 12.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C159340E03
1.094,2.156 1,1.958 1,1.958 2.031,2.24 false 1.313,2.875 1.427,3.063 1.427,3.063 1.51,3.063 false 0.719,1.875 1.052,2.031 0.333,0.156 10 false SST 1.552,2.979 1.719,3.135 0.167,0.156 10 false *1

Using SST, install the washer and bearing (outer race).

SST
09950-60020  (09951-00890, 09951-01030)

Text in Illustration
*1 Plate Washer

HINT:

First, fit a washer of the same thickness as the removed washer, and then after checking the tooth contact pattern, replace the washer with one of a different thickness if necessary.



Hide 41183C 13.INSTALL FRONT DIFFERENTIAL BREATHER PLUG OIL DEFLECTOR

a.
C159446

Install the front differential breather plug oil deflector with the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 41211A 14.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C159255E01
1.432,1.531 0.718,1.011 false 0.333,0.885 0.834,1.078 0.500,0.194 10 SST

Using SST and a press, press in the bearing (inner race).

SST
09506-35010  


Hide 15.TEMPORARILY INSTALL DIFFERENTIAL DRIVE PINION

Hide 41211B 16.INSTALL FRONT DRIVE PINION FRONT RADIAL BALL BEARING

a.
C159445E01
2.198,0.928 2.679,1.263 false 2.734,1.229 3.356,1.489 0.621,0.260 10 SST

Using SST and a hammer, lightly tap in the bearing (inner race) to install it.

SST
09316-60011  (09316-00041)


Hide 41214C 17.INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 18.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

a.
U152225E01
1.448,0.646 1.01,0.552 false 0.74,0.469 1.063,0.656 0.323,0.188 10 false SST 2.635,0.698 2.844,0.885 0.208,0.188 10 false *a 0.49,1.458 0.698,1.646 0.208,0.188 10 false *b

Using SST, install the companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

Text in Illustration
*a Turn
*b Hold


b.

Coat the threads of the nut with hypoid gear oil LSD.


c.
C159272E01
0.348,0.441 0.663,0.583 0.316,0.142 10 SST 0.717,0.544 1.152,0.747 false

Using SST to hold the companion flange.

SST
09330-00021  (09330-00030)


d.

Tighten the nut until the standard preload is reached.

Torque:

451 N*m (4599 kgf*cm, 333 ft.*lbf) or less


NOTICE:

As there is no spacer, tighten the nut a little at a time, being careful not to overtighten it.



e.
C353022

Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

Standard Preload (at Starting):
Bearing Specified Condition
New 2.69 to 3.19 N*m (28 to 32 kgf*cm, 24 to 28 in.*lbf)
Reused 1.86 to 2.17 N*m (19 to 22 kgf*cm, 17 to 19 in.*lbf)


If necessary, disassemble and inspect the differential assembly.


Hide 41311 19.INSTALL FRONT DIFFERENTIAL CASE

a.

Remove the bearing retainer.


b.

Install the differential case to the differential carrier.


Hide 41141L 20.INSTALL FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER

a.
C160133E01
2.303,0.58 2.441,0.750 0.139,0.170 10 A 1.4,0.626 1.539,0.795 0.139,0.170 10 A 0.919,0.767 1.058,0.937 0.139,0.170 10 A 0.524,0.918 0.662,1.088 0.139,0.170 10 A 2.909,1.068 3.047,1.238 0.139,0.170 10 A 3.012,1.569 3.150,1.739 0.139,0.170 10 A 1.389,2.706 1.528,2.876 0.139,0.170 10 A 1.018,2.442 1.156,2.612 0.139,0.170 10 A 0.832,2.235 0.970,2.405 0.139,0.170 10 A 0.623,2.067 0.761,2.237 0.139,0.170 10 A 0.142,1.907 0.281,2.076 0.139,0.170 10 A 2.976,1.927 3.229,2.096 0.253,0.170 10 B 2.71,2.704 2.963,2.874 0.253,0.170 10 B 2.311,2.775 2.564,2.944 0.253,0.170 10 B

Install the differential cross shaft bearing retainer and differential support with the 14 bolts.

Torque:
for bolt A : 65 N*m (663 kgf*cm, 48 ft.*lbf)
for bolt B : 155 N*m (1581 kgf*cm, 114 ft.*lbf)


Hide 41110V 21.INSTALL FRONT DIFFERENTIAL UNION

a.
C159447

Install the front differential union.


Hide 22.ADJUST BACKLASH BETWEEN DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION

a.
C159798E01
1.617,1.127 0.848,0.749 false 0.485,0.627 0.947,0.838 0.461,0.211 10 SST

Using SST and a dial indicator, measure the ring gear backlash.

SST
09564-33010  

Standard backlash:

0.17 to 0.27 mm (0.00670 to 0.01062 in.)


If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.

HINT:
·

There should be no clearance between the plate washer and differential case.

·

Make sure that there is ring gear backlash.



Washer Thickness:
Thickness Thickness
1.49 to 1.51 mm (0.0587 to 0.0594 in.) 1.93 to 1.95 mm (0.0760 to 0.0767 in.)
1.51 to 1.53 mm (0.0595 to 0.0602 in.) 1.95 to 1.97 mm (0.0768 to 0.0775 in.)
1.53 to 1.55 mm (0.0603 to 0.0610 in.) 1.97 to 1.99 mm (0.0776 to 0.0783 in.)
1.55 to 1.57 mm (0.0611 to 0.0618 in.) 1.99 to 2.01 mm (0.0784 to 0.0791 in.)
1.57 to 1.59 mm (0.0619 to 0.0625 in.) 2.01 to 2.03 mm (0.0792 to 0.0799 in.)
1.59 to 1.61 mm (0.0626 to 0.0633 in.) 2.03 to 2.05 mm (0.0800 to 0.0807 in.)
1.61 to 1.63 mm (0.0634 to 0.0641 in.) 2.05 to 2.07 mm (0.0808 to 0.0814 in.)
1.63 to 1.65 mm (0.0642 to 0.0649 in.) 2.07 to 2.09 mm (0.0815 to 0.0822 in.)
1.65 to 1.67 mm (0.0650 to 0.0657 in.) 2.09 to 2.11 mm (0.0823 to 0.0830 in.)
1.67 to 1.69 mm (0.0658 to 0.0665 in.) 2.11 to 2.13 mm (0.0831 to 0.0838 in.)
1.69 to 1.71 mm (0.0666 to 0.0673 in.) 2.13 to 2.15 mm (0.0839 to 0.0846 in.)
1.71 to 1.73 mm (0.0674 to 0.0681 in.) 2.15 to 2.17 mm (0.0847 to 0.0854 in.)
1.73 to 1.75 mm (0.0682 to 0.0688 in.) 2.17 to 2.19 mm (0.0855 to 0.0862 in.)
1.75 to 1.77 mm (0.0689 to 0.0696 in.) 2.19 to 2.21 mm (0.0863 to 0.0870 in.)
1.77 to 1.79 mm (0.0697 to 0.0704 in.) 2.21 to 2.23 mm (0.0871 to 0.0877 in.)
1.79 to 1.81 mm (0.0705 to 0.0712 in.) 2.23 to 2.25 mm (0.0878 to 0.0885 in.)
1.81 to 1.83 mm (0.0713 to 0.0720 in.) 2.25 to 2.27 mm (0.0886 to 0.0893 in.)
1.83 to 1.85 mm (0.0721 to 0.0728 in.) 2.27 to 2.29 mm (0.0894 to 0.0901 in.)
1.85 to 1.87 mm (0.0729 to 0.0736 in.) 2.29 to 2.31 mm (0.0902 to 0.0909 in.)
1.87 to 1.89 mm (0.0737 to 0.0744 in.) 2.31 to 2.33 mm (0.0910 to 0.0917 in.)
1.89 to 1.91 mm (0.0745 to 0.0751 in.) 2.33 to 2.35 mm (0.0918 to 0.0925 in.)
1.91 to 1.93 mm (0.0752 to 0.0759 in.) -



Hide 23.INSPECT TOTAL PRELOAD

a.
C353022

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Standard Preload (at Starting):
Bearing Specified Condition
New 4.30 to 5.60 N*m (44 to 57 kgf*cm, 39 to 49 in.*lbf)
Reused 3.19 to 4.30 N*m (33 to 43 kgf*cm, 29 to 38 in.*lbf)


NOTICE:

Record the differential ring gear preload.


If necessary, disassemble and inspect the differential.


Hide 24.INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

a.

Remove the bearing retainer and differential case.


b.
R013220

Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.


c.

Install the differential case to the differential carrier.


d.
C160133E01
2.303,0.58 2.441,0.750 0.139,0.170 10 A 1.4,0.626 1.539,0.795 0.139,0.170 10 A 0.919,0.767 1.058,0.937 0.139,0.170 10 A 0.524,0.918 0.662,1.088 0.139,0.170 10 A 2.909,1.068 3.047,1.238 0.139,0.170 10 A 3.012,1.569 3.150,1.739 0.139,0.170 10 A 1.389,2.706 1.528,2.876 0.139,0.170 10 A 1.018,2.442 1.156,2.612 0.139,0.170 10 A 0.832,2.235 0.970,2.405 0.139,0.170 10 A 0.623,2.067 0.761,2.237 0.139,0.170 10 A 0.142,1.907 0.281,2.076 0.139,0.170 10 A 2.976,1.927 3.229,2.096 0.253,0.170 10 B 2.71,2.704 2.963,2.874 0.253,0.170 10 B 2.311,2.775 2.564,2.944 0.253,0.170 10 B

Install the differential cross shaft bearing retainer and front differential front support assembly LH with the 14 bolts.

Torque:
for bolt A : 65 N*m (663 kgf*cm, 48 ft.*lbf)
for bolt B : 155 N*m (1581 kgf*cm, 114 ft.*lbf)


e.

Hold the companion flange firmly and rotate the ring gear in both directions.


f.

Remove the differential case, side bearing retainer and differential case.


g.

Inspect the tooth contact pattern.

C116070E05
1.581,1.833 1.830,2.026 0.249,0.193 10 *a 2.871,0.522 3.098,0.682 0.228,0.161 10 *b 2.774,3.37 3.008,3.539 0.233,0.169 10 *e 4.965,0.478 5.169,0.652 0.204,0.174 10 *c 5.072,3.354 5.270,3.529 0.198,0.174 10 *f 3.689,4.607 3.956,4.846 0.266,0.240 10 *g 3.678,2.001 3.916,2.177 0.238,0.176 10 *d

Text in Illustration
*a Proper Contact *b Heel Contact
*c Face Contact *d Select an adjusting washer that will shift the drive pinion closer to the ring gear (*b, *c)
*e Toe Contact *f Flank Contact
*g Select an adjusting washer that will shift the drive pinion away from the ring gear (*e, *f) - -

If the teeth are not engaged properly, use the following chart to select the appropriate washer for correction.

Washer Thickness:
Thickness Thickness
1.815 to 1.835 mm (0.0715 to 0.0722 in.) 2.065 to 2.085 mm (0.0813 to 0.0820 in.)
1.840 to 1.860 mm (0.0725 to 0.0732 in.) 2.090 to 2.110 mm (0.0823 to 0.0830 in.)
1.865 to 1.885 mm (0.0735 to 0.0742 in.) 2.115 to 2.135 mm (0.0833 to 0.0840 in.)
1.890 to 1.910 mm (0.0744 to 0.0751 in.) 2.140 to 2.160 mm (0.0843 to 0.0850 in.)
1.915 to 1.935 mm (0.0754 to 0.0761 in.) 2.165 to 2.185 mm (0.0853 to 0.0860 in.)
1.940 to 1.960 mm (0.0764 to 0.0771 in.) 2.190 to 2.210 mm (0.0863 to 0.0870 in.)
1.965 to 1.985 mm (0.0774 to 0.0781 in.) 2.215 to 2.235 mm (0.0873 to 0.0879 in.)
1.990 to 2.010 mm (0.0784 to 0.0791 in.) 2.240 to 2.260 mm (0.0882 to 0.0889 in.)
2.015 to 2.035 mm (0.0794 to 0.0801 in.) 2.265 to 2.285 mm (0.0892 to 0.0899 in.)
2.040 to 2.060 mm (0.0804 to 0.0811 in.) -



Hide 41204E 25.REMOVE FRONT DRIVE PINION COMPANION FLANGE FRONT NUT

Hide 41204D 26.REMOVE FRONT DRIVE PINION FRONT COMPANION FLANGE SUB-ASSEMBLY

Hide 41214C 27.REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41141L 28.REMOVE FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER

Hide 41211B 31.REMOVE FRONT DRIVE PINION FRONT RADIAL BALL BEARING

Hide 41231F 32.INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER

a.

Install a new bearing spacer.


Hide 33.TEMPORARILY INSTALL DIFFERENTIAL DRIVE PINION

Hide 41311 34.INSTALL FRONT DIFFERENTIAL CASE

Hide 41141L 35.INSTALL FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER

a.
C214104E02
1.417,0.229 1.667,0.229 1.667,0.229 1.823,0.583 true 1.25,0.146 1.49,0.365 0.24,0.219 10 false *a 0.938,1.531 1.125,1.667 0.188,0.135 10 false A

Remove any old FIPG material and be careful not to drop oil on the contact surfaces of the differential carrier and side bearing retainer.

Text in Illustration
*a Seal Packing


b.

Clean the contact surfaces with any residual FIPG material using gasoline or alcohol.


c.

Apply seal packing to the differential carrier as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


Standard Seal Diameter (A):

2.0 to 3.0 mm (0.0788 to 0.118 in.)


HINT:

Install the side bearing retainer within 10 minutes of applying seal packing.



d.
C160133E01
2.303,0.58 2.441,0.750 0.139,0.170 10 A 1.4,0.626 1.539,0.795 0.139,0.170 10 A 0.919,0.767 1.058,0.937 0.139,0.170 10 A 0.524,0.918 0.662,1.088 0.139,0.170 10 A 2.909,1.068 3.047,1.238 0.139,0.170 10 A 3.012,1.569 3.150,1.739 0.139,0.170 10 A 1.389,2.706 1.528,2.876 0.139,0.170 10 A 1.018,2.442 1.156,2.612 0.139,0.170 10 A 0.832,2.235 0.970,2.405 0.139,0.170 10 A 0.623,2.067 0.761,2.237 0.139,0.170 10 A 0.142,1.907 0.281,2.076 0.139,0.170 10 A 2.976,1.927 3.229,2.096 0.253,0.170 10 B 2.71,2.704 2.963,2.874 0.253,0.170 10 B 2.311,2.775 2.564,2.944 0.253,0.170 10 B

Install the front differential cross shaft bearing retainer and front differential front support assembly LH with the 11 bolts (A), and new 3 bolts (B).

Torque:
for bolt A : 65 N*m (663 kgf*cm, 48 ft.*lbf)
for bolt B : 155 N*m (1581 kgf*cm, 114 ft.*lbf)

NOTICE:

Do not add oil or drive the vehicle immediately after installing the cover, and leave it as is for at least an hour. Also, for 12 hours or less, avoid rapid acceleration/deceleration.



Hide 41211B 36.INSTALL FRONT DRIVE PINION FRONT RADIAL BALL BEARING

a.
C159432E01
2.198,1.044 2.704,1.293 false 2.765,1.237 3.139,1.428 0.375,0.191 10 SST

Using SST and a hammer, lightly tap in the bearing (inner race) to install it.

SST
09316-60011  (09316-00041)


Hide 41214C 37.INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41101D 38.INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL

a.
C159273E01
1.964,1.266 2.465,1.352 false 2.505,1.298 2.959,1.503 0.455,0.206 10 SST

Using SST and a hammer, tap in a new oil seal.

SST
09502-12010  
09316-60011  (09316-00041)

Standard oil seal depth:

5.6 to 6.6 mm (0.221 to 0.259 in.)



b.

Coat the lip of the oil seal with MP grease.


Hide 41204D 39.INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
U152225E01
1.448,0.646 1.01,0.552 false 0.74,0.469 1.063,0.656 0.323,0.188 10 false SST 2.635,0.698 2.844,0.885 0.208,0.188 10 false *a 0.49,1.458 0.698,1.646 0.208,0.188 10 false *b

Using SST, install the companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

Text in Illustration
*a Turn
*b Hold


b.
C159272E01
0.348,0.441 0.663,0.583 0.316,0.142 10 SST 0.717,0.544 1.152,0.747 false

Using SST to hold the companion flange.

SST
09330-00021  (09330-00030)


c.

Coat the threads of a new nut with hypoid gear oil LSD.


d.

Install the nut by tightening it until the standard preload is reached.

Torque:

451 N*m (4599 kgf*cm, 333 ft.*lbf) or less



e.
C353022

Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

Standard total preload (at starting):
Bearing Specified Condition
New 3.05 to 3.55 N*m (32 to 36kgf*cm, 27 to 31 in.*lbf)
Reused 2.22 to 2.53 N*m (23 to 25 kgf*cm, 20 to 22 in.*lbf)


If the preload is more than the specification, replace the bearing spacer.

If the preload is less than the specification, tighten the nut with 13 N*m (130 kgf*cm, 9 ft.*lbf) of torque at a time until the specified preload is reached.

Torque:
451 N*m (4599 kgf*cm, 333 ft.*lbf)

or less


If the maximum torque is exceeded while tightening the nut, replace the bearing spacer and repeat the preload procedure.

HINT:

Do not loosen the nut to reduce the preload.



Hide 40.INSPECT TOTAL PRELOAD

a.
C353022

With the drive pinion contacting the tooth side of the ring gear, use a torque wrench to measure the total preload.

Standard total preload (at starting):
Bearing Specified Condition
New 4.66 to 5.96 N*m (48 to 60 kgf*cm, 42 to 52 in.*lbf)
Reused 3.55 to 4.66 N*m (37 to 47 kgf*cm, 32 to 41 in.*lbf)



Hide 41.INSPECT BACKLASH BETWEEN DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION

a.
C159798E01
1.617,1.127 0.848,0.749 false 0.485,0.627 0.947,0.838 0.461,0.211 10 SST

Using SST and a dial indicator, measure the ring gear backlash.

SST
09564-33010  

Standard backlash:

0.17 to 0.27 mm (0.00670 to 0.0106 in.)



Hide 41204D 42.INSPECT RUNOUT OF FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C160138E02
2.563,2.656 2.771,2.844 0.208,0.188 10 false *a

Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Text in Illustration
*a 55 mm (2.17 in.)

Maximum Runout:
Runout Specified Condition
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)


If the runout is more than the maximum, replace the companion flange.


Hide 41204E 43.STAKE FRONT DRIVE PINION COMPANION FLANGE FRONT NUT

a.
C160139

Using a chisel and hammer, stake the nut.


Hide 41304P 44.INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

a.
C159275E01
1.541,0.908 1.228,0.699 false 0.889,0.6 1.215,0.756 0.326,0.156 10 SST

Using SST and a plastic-faced hammer, tap in a new oil seal until its surface is flush with the differential carrier end.

SST
09608-32010  


b.

Coat the lip of the oil seal with MP grease.

Standard oil seal depth:

-0.45 to 0.45 mm (-0.0177 to 0.0177 in.)



Hide 41306F 45.INSTALL DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY

a.
C159276

Install a new snap ring onto the side gear inter shaft.


b.

Using a plastic-faced hammer, install the side gear inter shaft onto the differential case.


c.

Check that there is 2 to 3 mm (0.0788 to 0.118 in.) of play in the axial direction.


d.

Check that the side gear inter shaft does not come out when trying to pull it out by hand.


Hide 41320 46.INSTALL FRONT DIFFERENTIAL TUBE ASSEMBLY

a.
C159277E02
1.635,1.177 1.063,1.625 true 0.875,1.552 1.073,1.729 0.198,0.177 10 false *a

Remove any old FIPG material and be careful not to drop oil on the contact surfaces of the differential tube and bearing retainer.

Text in Illustration
*a Seal Packing


b.

Clean the contact surfaces with any residual FIPG material using gasoline or alcohol.


c.

Apply seal packing to the bearing retainer as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


HINT:

Install the differential tube within 10 minutes of applying seal packing.



d.

Install the differential tube onto the bearing retainer.


e.
C159258

Clean the threads of 4 new bolts and the retainer bolt holes with toluene or trichloroethylene.


f.

Apply adhesive to 2 to 3 threads of each bolt end.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



g.

Install the 4 bolts.

Torque:

65 N*m (663 kgf*cm, 48 ft.*lbf)


NOTICE:

Do not add oil or drive the vehicle immediately after installing the cover, and leave it as is for at least an hour. Also, for 12 hours or less, avoid rapid acceleration/deceleration.



Hide 41400 47.INSTALL AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR

a.
C159278E02
1.656,1.469 1.896,1.865 1.896,1.865 1.74,1.865 false 1.563,1.76 1.771,1.938 0.208,0.177 10 false *a

Remove any old FIPG material and be careful not to drop oil on the contact surfaces of the differential tube and actuator.

Text in Illustration
*a Seal Packing


b.

Clean the contact surfaces with any residual FIPG material using gasoline or alcohol.


c.

Apply seal packing to the differential tube as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


HINT:

Install the actuator within 10 minutes of applying seal packing.



d.
C159279

Clean the threads of the 4 bolts and retainer bolt holes with toluene or trichloroethylene.


e.

Install the actuator to the differential tube.


f.

Install the 4 bolts.

Torque:
21 N*m (209 kgf*cm, 15 ft.*lbf)