Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY
RM27L0U _52 Drivetrain _049314 AXLE AND DIFFERENTIAL _0235701 REAR DIFFERENTIAL CARRIER ASSEMBLY A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STRAIGHT PIN

a.
C180992E03
1.521,2.708 1.635,2.708 1.635,2.708 2.354,3.531 false 0.354,2.594 1.563,2.948 1.208,0.354 10 false 9.5 to 10 mm (0.374 to 0.394 in.)

Using a plastic-faced hammer, tap in the straight pins until their protrusion amounts are at the specified values shown in the illustration below.


Hide 2.INSTALL DIFFERENTIAL RING GEAR

a.
SA02160E07
0.583,0.323 1.156,1 false 0.146,0.073 0.604,0.406 0.458,0.333 10 false Boiling Water

Clean the contact surfaces of the differential case and ring gear.


b.

Heat the ring gear to about 100°C (212°F) in boiling water.


c.

Carefully take the ring gear out of the boiling water.


d.

After the moisture on the ring gear has completely evaporated, quickly set the ring gear onto the differential case.

HINT:
·

Align the matchmarks on the ring gear and differential case.

·

Temporarily install the 12 bolts so that the bolt holes in the ring gear and differential case are aligned.




e.

After the ring gear cools down sufficiently, apply adhesive to the bolts and install them.

Torque:
196 N*m (2000 kgf*cm, 145 ft.*lbf)

Adhesive:

Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent



Hide 41301A 3.INSTALL REAR DIFFERENTIAL CASE BEARING

a.
C181022E01
2.25,0.565 2.563,0.735 0.313,0.170 10 SST 1.815,0.657 2.236,0.657 2.236,0.657 2.018,1.052 false

Using SST and a press, press in the 2 bearings (inner race).

SST
09950-70010  (09951-07100)


Hide 41301A 4.INSTALL REAR DIFFERENTIAL CASE BEARING

HINT:

When replacing the 2 differential case bearings, fit the thinnest washer to each bearing. When reusing the bearings, fit a washer of the same thickness as the one removed to each bearing.


a.
C180997E02
2.688,0.729 2.813,1.563 false 1.427,0.75 0.802,0.521 0.802,0.521 1.208,1.146 false 2.406,1.563 3.354,1.792 0.948,0.229 10 true Plate Washer 0.5,0.427 0.823,0.583 0.323,0.156 10 false SST

Install a new plate washer to the side bearing retainer.


b.

Using SST and a press, install the bearing (outer race) onto the differential case bearing retainer.

SST
09950-70010  (09951-07200)
09951-01000  


c.
C180999E02
2.365,0.771 2.26,1.458 true 1.313,0.74 0.385,0.521 0.385,0.521 1.219,1.354 false 1.833,1.458 2.75,1.646 0.917,0.188 10 true Plate Washer 0.042,0.438 0.354,0.615 0.313,0.177 10 false SST

Install a new plate washer onto the differential carrier.


d.

Using SST and a press, press in the bearing (outer race) onto the differential carrier assembly.

SST
09950-70010  (09951-07200)
09951-01000  


Hide 41201B 5.INSTALL REAR DRIVE PINION FRONT RADIAL BALL BEARING

a.
C181037E01
0.583,1.815 0.882,1.977 0.299,0.163 10 SST 1.179,2.154 0.933,1.908 0.933,1.908 1.725,2.153 false

Using SST, install the bearing (outer race).

SST
09950-60020  (09951-00890)
09218-56030  


Hide 41201A 6.INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C181036E01
0.665,1.846 0.963,2.039 0.298,0.194 10 SST 1.179,2.154 1.013,1.94 1.013,1.94 2.071,2.111 false

Using SST, install the washer and bearing (outer race).

SST
09218-56030  
09951-01100  

HINT:

First, fit a washer of the same thickness as the removed washer, and then after checking the tooth contact pattern, replace the washer with one of a different thickness if necessary.



Hide 41183 7.INSTALL REAR DIFFERENTIAL BREATHER PLUG OIL DEFLECTOR

a.
C180994

Install the rear differential breather plug oil deflector with the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 41201A 8.INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C183213E01
0.085,1.688 0.384,1.858 0.300,0.170 10 SST 0.619,1.768 0.435,1.768 0.435,1.768 0.536,2.016 false

Using SST and a press, press in the bearing (inner race).

SST
09502-24010  
09308-14010  


Hide 9.TEMPORARILY INSTALL DIFFERENTIAL DRIVE PINION

a.

Install the differential drive pinion.


Hide 41301 10.INSTALL REAR DIFFERENTIAL CASE SUB-ASSEMBLY

a.
C180993

Install the rear differential case sub-assembly.


Hide 41141B 11.INSTALL REAR DIFFERENTIAL SIDE BEARING RETAINER

a.
C180991

Install the rear differential side bearing retainer with the 12 bolts.

HINT:

Tighten the bolts gradually, skipping to the bolt on the opposite side.


Torque:
70 N*m (714 kgf*cm, 52 ft.*lbf)


Hide 41108C 12.INSTALL REAR DIFFERENTIAL CARRIER COVER BREATHER PLUG

a.
C181031

Install the rear differential carrier cover breather plug.

Torque:
21 N*m (210 kgf*cm, 15 ft.*lbf)


Hide 41201B 13.INSTALL REAR DRIVE PINION FRONT RADIAL BALL BEARING

a.
C181021E01
2.633,1.205 2.951,1.365 0.318,0.161 10 SST 2.243,1.285 2.613,1.285 2.613,1.285 2.28,1.563 false

Using SST and a hammer, lightly tap in the bearing (inner race) to install it.

SST
09316-60011  (09316-00011)
09506-30012  


Hide 41214 14.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

a.
C181009

Install the rear differential drive pinion oil slinger.


Hide 15.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

a.
C181018E01
2.199,1.023 2.556,1.207 0.357,0.184 10 SST 2.187,1.102 2.065,1.102 2.065,1.102 1.742,1.545 false

Using SST, install the companion flange.

HINT:

Use the propeller shaft installation nuts when mounting SST on the flange


SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09956-03020)
09955-03050  


b.

Coat the threads of the nut with hypoid gear oil.


c.
C181027E05
0.938,2.042 0.719,2.281 false 0.531,2.313 0.865,2.51 0.333,0.198 10 false SST

Using SST to hold the companion flange.

SST
09330-00021  


d.

Using a socket wrench (30mm), tighten the nut until the standard preload is reached.

Torque:
441 N*m (4497 kgf*cm, 325 ft.*lbf)

or less


NOTICE:
·

As there is no spacer, tighten the nut a little at a time, being careful not to overtighten it.

·

Install nuts on the bolts to protect them, as shown in the illustration.




e.
C181029

Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

Standard Preload (at Starting):
Bearing Specified Condition
New 2.04 to 3.24 N*m (21 to 33 kgf*cm, 18 to 29 in.*lbf)
Reused 1.52 to 2.23 N*m (15 to 23 kgf*cm, 13 to 20 in.*lbf)


If necessary, disassemble and inspect the differential assembly.


Hide 16.ADJUST BACKLASH BETWEEN DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION

a.
C181024E01
1.138,1.612 1.524,0.552 1.524,0.552 1.679,0.552 false 1.702,0.46 2.023,0.630 0.321,0.170 10 SST

Using SST and a dial indicator, measure the ring gear backlash.

SST
09564-34010  

Standard backlash:

0.1 to 0.2 mm (0.00394 to 0.00787 in.)


If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.

HINT:
·

There should be no clearance between the plate washer and differential case.

·

Make sure that there is ring gear backlash.



Washer Thickness:
Thickness Thickness
1.55 to 1.57 mm (0.0610 to 0.0618 in.) 1.91 to 1.93 mm (0.0752 to 0.0760 in.)
1.57 to 1.59 mm (0.0618 to 0.0626 in.) 1.93 to 1.95 mm (0.0760 to 0.0768 in.)
1.59 to 1.61 mm (0.0626 to 0.0634 in.) 1.95 to 1.97 mm (0.0768 to 0.0776 in.)
1.61 to 1.63 mm (0.0634 to 0.0642 in.) 1.97 to 1.99 mm (0.0776 to 0.0783 in.)
1.63 to 1.65 mm (0.0642 to 0.0650 in.) 1.99 to 2.01 mm (0.0783 to 0.0791 in.)
1.65 to 1.67 mm (0.0650 to 0.0657 in.) 2.01 to 2.03 mm (0.0791 to 0.0799 in.)
1.67 to 1.69 mm (0.0657 to 0.0665 in.) 2.03 to 2.05 mm (0.0799 to 0.0807 in.)
1.69 to 1.71 mm (0.0665 to 0.0673 in.) 2.05 to 2.07 mm (0.0807 to 0.0815 in.)
1.71 to 1.73 mm (0.0673 to 0.0681 in.) 2.07 to 2.09 mm (0.0815 to 0.0823 in.)
1.73 to 1.75 mm (0.0681 to 0.0689 in.) 2.09 to 2.11 mm (0.0823 to 0.0831 in.)
1.75 to 1.77 mm (0.0689 to 0.0697 in.) 2.11 to 2.13 mm (0.0831 to 0.0839 in.)
1.77 to 1.79 mm (0.0697 to 0.0705 in.) 2.13 to 2.15 mm (0.0839 to 0.0846 in.)
1.79 to 1.81 mm (0.0705 to 0.0713 in.) 2.15 to 2.17 mm (0.0846 to 0.0854 in.)
1.81 to 1.83 mm (0.0713 to 0.0720 in.) 2.17 to 2.19 mm (0.0854 to 0.0862 in.)
1.83 to 1.85 mm (0.0720 to 0.0728 in.) 2.19 to 2.21 mm (0.0862 to 0.0870 in.)
1.85 to 1.87 mm (0.0728 to 0.0736 in.) 2.21 to 2.23 mm (0.0870 to 0.0878 in.)
1.87 to 1.89 mm (0.0736 to 0.0744 in.) 2.23 to 2.25 mm (0.0878 to 0.0886 in.)
1.89 to 1.91 mm (0.0744 to 0.0752 in.) 2.25 to 2.27 mm (0.0886 to 0.0894 in.)



Hide 17.INSPECT TOTAL PRELOAD

a.
C181029

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Standard Preload (at Starting):
Bearing Specified Condition
New 2.33 to 4.47 N*m (24 to 46 kgf*cm, 21 to 40 in.*lbf)
Reused 1.79 to 3.34 N*m (18 to 34 kgf*cm, 16 to 30 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 18.INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

a.

Remove the bearing retainer and differential case.


b.
R013220

Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.


c.

Install the differential case to the differential carrier.


d.
C180991

Install the rear differential side bearing retainer with the 12 bolts.

HINT:

Tighten the bolts gradually, skipping to the bolt on the opposite side.


Torque:
70 N*m (714 kgf*cm, 52 ft.*lbf)


e.

Hold the companion flange firmly and rotate the ring gear in both directions.


f.

Remove the differential case, side bearing retainer and differential case.


g.

Inspect the tooth contact pattern.

C116070E02
1.062,1.909 2.104,2.102 1.041,0.193 10 Proper Contact 2.946,0.578 3.833,0.739 0.887,0.161 10 Heel Contact 2.908,4.538 3.766,4.707 0.858,0.169 10 Toe Contact 5.115,0.539 6.022,0.714 0.907,0.174 10 Face Contact 5.514,4.543 6.447,4.718 0.934,0.174 10 Flank Contact 2.853,5.065 6.407,5.397 3.554,0.332 10 Select an adjusting washer that will shift the drive pinion away from the ring gear 2.928,2.374 6.497,2.738 3.569,0.363 10 Select an adjusting washer that will bring the drive pinion closer to the ring gear.

If the teeth are not engaged properly, use the following chart to select the appropriate washer for correction.

Washer Thickness:
Thickness Thickness
1.73 to 1.75 mm (0.0681 to 0.0689 in.) 2.05 to 2.07 mm (0.0807 to 0.0815 in.)
1.75 to 1.77 mm (0.0689 to 0.0697 in.) 2.07 to 2.09 mm (0.0815 to 0.0823 in.)
1.77 to 1.79 mm (0.0697 to 0.0705 in.) 2.09 to 2.11 mm (0.0823 to 0.0831 in.)
1.79 to 1.81 mm (0.0705 to 0.0713 in.) 2.11 to 2.13 mm (0.0831 to 0.0839 in.)
1.81 to 1.83 mm (0.0713 to 0.0720 in.) 2.13 to 2.15 mm (0.0839 to 0.0846 in.)
1.83 to 1.85 mm (0.0720 to 0.0728 in.) 2.15 to 2.17 mm (0.0846 to 0.0854 in.)
1.85 to 1.87 mm (0.0728 to 0.0736 in.) 2.17 to 2.19 mm (0.0854 to 0.0862 in.)
1.87 to 1.89 mm (0.0736 to 0.0744 in.) 2.19 to 2.21 mm (0.0862 to 0.0870 in.)
1.89 to 1.91 mm (0.0744 to 0.0752 in.) 2.21 to 2.23 mm (0.0870 to 0.0878 in.)
1.91 to 1.93 mm (0.0752 to 0.0760 in.) 2.23 to 2.25 mm (0.0878 to 0.0886 in.)
1.93 to 1.95 mm (0.0760 to 0.0768 in.) 2.25 to 2.27 mm (0.0886 to 0.0894 in.)
1.95 to 1.97 mm (0.0768 to 0.0776 in.) 2.27 to 2.29 mm (0.0894 to 0.0902 in.)
1.97 to 1.99 mm (0.0776 to 0.0783 in.) 2.29 to 2.31 mm (0.0902 to 0.0910 in.)
1.99 to 2.01 mm (0.0783 to 0.0791 in.) 2.31 to 2.33 mm (0.0910 to 0.0917 in.)
2.01 to 2.03 mm (0.0791 to 0.0799 in.) 2.33 to 2.35 mm (0.0917 to 0.0925 in.)
2.03 to 2.05 mm (0.0799 to 0.0807 in.) -



Hide 41204 19.REMOVE REAR DRIVE PINION FRONT COMPANION FLANGE SUB-ASSEMBLY

Hide 41214 20.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41141B 21.REMOVE REAR DIFFERENTIAL SIDE BEARING RETAINER

Hide 41301 22.REMOVE REAR DIFFERENTIAL CASE SUB-ASSEMBLY

Hide 41201B 24.REMOVE REAR DRIVE PINION FRONT RADIAL BALL BEARING

Hide 41231 25.INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.

Install a new bearing spacer.


Hide 26.TEMPORARILY INSTALL DIFFERENTIAL DRIVE PINION

Hide 41301 27.INSTALL REAR DIFFERENTIAL CASE SUB-ASSEMBLY

Hide 41141B 28.INSTALL REAR DIFFERENTIAL SIDE BEARING RETAINER

a.

Remove any old FIPG material and be careful not to drop oil on the contact surfaces of the differential carrier and side bearing retainer.


b.

Clean the contact surfaces with any residual FIPG material using gasoline or alcohol.


c.

Apply seal packing to the side bearing retainer as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


HINT:

Install the side bearing retainer within 10 minutes of applying seal packing.



d.
C180991

Install the rear differential side bearing retainer with the 12 bolts.

HINT:

Tighten the bolts gradually, skipping to the bolt on the opposite side.


Torque:
70 N*m (714 kgf*cm, 52 ft.*lbf)


Hide 41201B 29.INSTALL REAR DRIVE PINION FRONT RADIAL BALL BEARING

a.
C181021E01
2.633,1.205 2.951,1.365 0.318,0.161 10 SST 2.243,1.285 2.613,1.285 2.613,1.285 2.28,1.563 false

Using SST and a hammer, lightly tap in the bearing (inner race) to install it.

SST
09316-60011  (09316-00011)
09506-30012  


Hide 41214 30.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

a.
C181009

Install the rear differential drive pinion oil slinger.


Hide 41201C 31.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C181145E01
1.376,0.425 2.161,0.288 2.161,0.288 1.793,0.489 false 2.19,0.191 2.499,0.426 0.309,0.235 10 SST

Using SST and a hammer, tap in a new oil seal.

SST
09223-56010  
09527-17011  

Standard oil seal depth:

0 to 0.1 mm (0 to 0.0394 in.)



b.

Coat the lip of the oil seal with MP grease.


Hide 41204 32.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY FRONT

a.
C181018E01
2.199,1.023 2.556,1.207 0.357,0.184 10 SST 2.187,1.102 2.065,1.102 2.065,1.102 1.742,1.545 false

Using SST, install the companion flange.

HINT:

Use the propeller shaft installation nuts when mounting SST on the flange.


SST
09950-30012  (09951-03010, 09953-03010, 09954-03010)
09955-03050  


Hide 33.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

a.
C181027E05
0.938,2.042 0.719,2.281 false 0.531,2.313 0.865,2.51 0.333,0.198 10 false SST

Using SST to hold the companion flange.

SST
09330-00021  (09330-00030)


b.

Coat the threads of a new nut with hypoid gear oil.


c.

Using a socket wrench (30mm). install the nut by tightening it until the standard preload is reached.

NOTICE:

Install nuts on the bolts to protect them, as shown in the illustration.


Torque:
441 N*m (4497 kgf*cm, 325 ft.*lbf)

or less



d.
C181029

Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

Standard Preload (at Starting):
Bearing Specified Condition
New 2.04 to 3.24 N*m (21 to 33 kgf*cm, 18 to 29 in.*lbf)
Reused 1.52 to 2.23 N*m (15 to 23 kgf*cm, 13 to 20 in.*lbf)


If the preload is greater than the specification, replace the bearing spacer.

If the preload is less than the specification, retighten the nut with until the specified preload is reached.

Torque:
441 N*m (4497 kgf*cm, 325 ft.*lbf)

or less


If the maximum torque is exceeded while retightening the nut, replace the bearing spacer and repeat the preload procedure.

HINT:

Do not loosen the nut to reduce the preload.



Hide 34.INSPECT TOTAL PRELOAD

a.
C181029

With the drive pinion contacting the tooth side of the ring gear, use a torque wrench to measure the total preload.

Standard Preload (at Starting):
Bearing Specified Condition
New 2.33 to 4.47 N*m (24 to 46 kgf*cm, 21 to 40 in.*lbf)
Reused 1.79 to 3.34 N*m (18 to 34 kgf*cm, 16 to 30 in.*lbf)



Hide 35.INSPECT BACKLASH BETWEEN DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION

a.
C181024E01
1.138,1.612 1.524,0.552 1.524,0.552 1.679,0.552 false 1.702,0.46 2.023,0.630 0.321,0.170 10 SST

Using SST and a dial indicator, measure the ring gear backlash.

SST
09564-34010  

Standard backlash:

0.1 to 0.2 mm (0.00394 to 0.00787 in.)



Hide 41204 36.INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C181030E04
1.667,1.823 2.719,2.021 1.052,0.198 10 true 72 mm (2.83 in.)

Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Maximum Runout:
Runout Specified Condition
Vertical runout 0.1 mm (0.00394 in.)
Lateral runout 0.1 mm (0.00394 in.)


If the runout is greater than the maximum, replace the companion flange.


Hide 41204B 37.STAKE REAR DRIVE PINION NUT

a.
C181003E01
1.349,1.438 1.650,1.598 0.301,0.161 10 SST 1.674,1.053 1.51,1.438 false

Using a chisel and hammer, stake the nut.

SST
09930-00010  


Hide 41334B 38.INSTALL REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

a.
C181006E03
1.656,1.354 1.656,1.656 1.656,1.656 1.448,1.458 false 0.969,2.563 1.156,2.698 false 1.292,2.865 1.063,3.052 false 1.313,2.313 1.469,2.521 false 1.531,1.677 1.844,1.833 0.313,0.156 10 false SST 0.313,2.469 1.01,2.646 0.698,0.177 10 false Differential 0.552,2.979 1.083,3.167 0.531,0.188 10 false Oil Seal 0.385,2.188 1.333,2.354 0.948,0.167 10 false -0.5 to 0.5 mm

Apply MP grease to 2 new oil seals.


b.

Using SST and a hammer, tap in the 2 oil seals.

SST
09223-15020  
09950-70010  (09951-07150)

NOTICE:

Make sure that the oil seal are installed in the proper locations.


Standard oil seal depth:

-0.50 to 0.50 mm (-0.0197 to 0.0197 in.)