Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › FRONT WHEEL ALIGNMENT
RM27L0U _53 Suspension _049316 ALIGNMENT / HANDLING DIAGNOSIS _0235714 FRONT WHEEL ALIGNMENT N

ALIGNMENT / HANDLING DIAGNOSIS  FRONT WHEEL ALIGNMENT  ADJUSTMENT  


CAUTION / NOTICE / HINT

NOTICE:

For vehicles equipped with VSC, if the wheel alignment has been adjusted, or if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:

1.

Disconnect the cable from the negative (-) battery terminal for more than 2 seconds.

2.

Reconnect the cable to the negative (-) battery terminal.

3.

Perform zero point calibration of the yaw rate and deceleration sensor, and test mode inspection (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).



PROCEDURE

Hide 2.MEASURE VEHICLE HEIGHT

NOTICE:

Before inspecting the wheel alignment, adjust the vehicle height to the specification.


a.
C180789E02
0.053,0.008 0.298,0.213 0.245,0.205 10 *a 0.062,2.449 0.287,2.653 0.226,0.205 10 *b 3.035,1.624 3.198,1.815 0.163,0.191 10 A 1.385,1.615 1.569,1.813 0.184,0.198 10 B 0.861,4.056 1.017,4.240 0.156,0.184 10 D 2.889,4.065 3.059,4.234 0.170,0.170 10 C

Press down on the vehicle several times to stabilize the suspension, and then measure the vehicle height.

Text in Illustration
*a Front Side
*b Rear Side

Measuring points:
A:

Ground clearance of the front drive shaft center

B:

Ground clearance of the front adjusting cam bolt center

C:

Ground clearance of the rear drive shaft center

D:

Ground clearance of the rear lower arm No. 1 adjusting cam bolt center


Standard Vehicle Height (Unloaded Vehicle):
Vehicle Model Tire Size Front A - B Rear C - D
USK60L-GKTSKA P275/65R18 8JJ 108.1 mm (4.26 in.) 30.3 mm (1.19 in.)
P275/55R20 8JJ 108.1 mm (4.26 in.) 30.3 mm (1.19 in.)
USK60L-GKTLKA P275/65R18 8JJ 107.6 mm (4.24 in.) 30.6 mm (1.20 in.)
P275/55R20 8JJ 107.6 mm (4.24 in.) 30.6 mm (1.20 in.)
USK60L-GKTZKA P275/55R20 8JJ 106.6 mm (4.20 in.) 39.1 mm (1.54 in.)
USK65L-GKTSKA P275/65R18 8JJ 101.9 mm (4.01 in.) 25.2 mm (0.99 in.)
P275/55R20 8JJ 101.9 mm (4.01 in.) 25.2 mm (0.99 in.)
USK65L-GKTLKA P275/65R18 8JJ 101.7 mm (4.00 in.) 25.3 mm (1.00 in.)
P275/55R20 8JJ 101.7 mm (4.00 in.) 25.3 mm (1.00 in.)
USK65L-GKTZKA P275/55R20 8JJ 100.3 mm (3.95 in.) 34.0 mm (1.34 in.)
USK65L-GKTSGA P275/65R18 8JJ 101.9 mm (4.01 in.) 25.2 mm (0.99 in.)
P275/55R20 8JJ 101.9 mm (4.01 in.) 25.2 mm (0.99 in.)
USK65L-GKTLGA P275/65R18 8JJ 101.7 mm (4.00 in.) 25.3 mm (1.00 in.)
P275/55R20 8JJ 101.7 mm (4.00 in.) 25.3 mm (1.00 in.)
USK65L-GKTZGA P275/55R20 8JJ 100.3 mm (3.95 in.) 34.0 mm (1.34 in.)


NOTICE:

The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.



Hide 3.INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

Z003382E32
2.563,0.917 2.823,0.896 false 1.115,1.438 0.833,1.135 false 0.646,1.052 0.823,1.219 0.177,0.167 10 false *1 2.854,0.802 3.052,0.969 0.198,0.167 10 false *2

a.

Install a camber-caster-kingpin gauge or place the front wheels on the center of a wheel alignment tester.

Text in Illustration
*1 Wheel Alignment Tester
*2 Gauge


b.

Inspect the camber, caster and steering axis inclination.

Standard Camber, Caster, Steering Axis Inclination (Unloaded Vehicle):
Vehicle Model Tire Size Camber Inclination Caster Inclination Steering Axis Inclination
USK60L-GKTSKA P275/65R18 8JJ -0°10' +/-45'
(-0.17° +/-0.75°)
3°46' +/-45'
(3.76° +/-0.75°)
13°11' +/-45'
(13.19° +/-0.75°)
P275/55R20 8JJ -0°10' +/-45'
(-0.17° +/-0.75°)
3°46' +/-45'
(3.76° +/-0.75°)
13°11' +/-45'
(13.19° +/-0.75°)
USK60L-GKTLKA P275/65R18 8JJ -0°10' +/-45'
(-0.16° +/-0.75°)
3°46' +/-45'
(3.77° +/-0.75°)
13°11' +/-45'
(13.18° +/-0.75°)
P275/55R20 8JJ -0°10' +/-45'
(-0.16° +/-0.75°)
3°46' +/-45'
(3.77° +/-0.75°)
13°11' +/-45'
(13.18° +/-0.75°)
USK60L-GKTZKA P275/55R20 8JJ -0°09' +/-45'
(-0.15° +/-0.75°)
3°56' +/-45'
(3.94° +/-0.75°)
13°10' +/-45'
(13.17° +/-0.75°)
USK65L-GKTSKA P275/65R18 8JJ -0°01' +/-45'
(-0.02° +/-0.75°)
3°38' +/-45'
(3.64° +/-0.75°)
13°03' +/-45'
(13.05° +/-0.75°)
P275/55R20 8JJ -0°01' +/-45'
(-0.02° +/-0.75°)
3°35' +/-45'
(3.59° +/-0.75°)
13°03' +/-45'
(13.05° +/-0.75°)
USK65L-GKTLKA P275/65R18 8JJ -0°01' +/-45'
(-0.01° +/-0.75°)
3°39' +/-45'
(3.65° +/-0.75°)
13°03' +/-45'
(13.05° +/-0.75°)
P275/55R20 8JJ -0°01' +/-45'
(-0.01° +/-0.75°)
3°35' +/-45'
(3.59° +/-0.75°)
13°03' +/-45'
(13.05° +/-0.75°)
USK65L-GKTZKA P275/55R20 8JJ 0°00' +/-45'
(0.00° +/-0.75°)
3°46' +/-45'
(3.76° +/-0.75°)
13°02' +/-45'
(13.03° +/-0.75°)
USK65L-GKTSGA P275/65R18 8JJ -0°01' +/-45'
(-0.02° +/-0.75°)
3°38' +/-45'
(3.64° +/-0.75°)
13°03' +/-45'
(13.05° +/-0.75°)
P275/55R20 8JJ -0°01' +/-45'
(-0.02° +/-0.75°)
3°35' +/-45'
(3.59° +/-0.75°)
13°03' +/-45'
(13.05° +/-0.75°)
USK65L-GKTLGA P275/65R18 8JJ -0°01' +/-45'
(-0.01° +/-0.75°)
3°39' +/-45'
(3.65° +/-0.75°)
13°03' +/-45'
(13.05° +/-0.75°)
P275/55R20 8JJ -0°01' +/-45'
(-0.01° +/-0.75°)
3°35' +/-45'
(3.59° +/-0.75°)
13°03' +/-45'
(13.05° +/-0.75°)
USK65L-GKTZGA P275/55R20 8JJ 0°00' +/-45'
(0.00° +/-0.75°)
3°46' +/-45'
(3.76° +/-0.75°)
13°02' +/-45'
(13.03° +/-0.75°)



Hide 4.ADJUST CAMBER AND CASTER

HINT:

After the camber has been adjusted, inspect the toe-in.


a.

Loosen the toe adjusting cam bolt and camber adjusting cam nut.


b.

Turn the toe adjusting cam and camber adjusting cam in both directions, and adjust the camber and caster to the center value.

HINT:

The camber and caster should be as close as possible to the center value.


C183664E02
3.512,0.037 3.716,0.228 0.205,0.191 10 *a 2.902,1.823 3.122,2.000 0.220,0.177 10 *1 4.086,1.83 4.300,2.007 0.214,0.177 10 *2 2.902,3.301 3.095,3.499 0.193,0.198 10 *3 4.086,3.301 4.349,3.499 0.262,0.198 10 *4

Text in Illustration
*1 Front Adjusting Cam LH *2 Front Adjusting Cam RH
*3 Rear Adjusting Cam LH *4 Rear Adjusting Cam RH
*a Front of the Vehicle - -


c.
C183666E03
2.51,3.292 2.51,4.094 true 1.302,3.458 1.302,4.073 false 1,1.938 1,1.177 true 2.583,2.385 2.583,1.188 true 2.167,2.375 2.167,0.844 true 2.375,2.531 2.167,2.375 true 1.885,4.323 1.885,3.115 false 1.813,3.042 1.885,3.104 true 0.979,0.125 1.5,0.323 0.521,0.198 10 false Camber 1,0.365 1.49,0.531 0.49,0.167 10 false Caster 1.583,0.625 2.646,0.802 1.063,0.177 10 false Measured Value 1.323,4.354 2.354,4.521 1.031,0.167 10 false Standard Value 2.229,4.146 3.177,4.313 0.948,0.167 10 false CAM=0°03' 0.885,4.094 1.813,4.26 0.927,0.167 10 false CAS=4°07' 0.563,0.969 1.51,1.135 0.948,0.167 10 false CAM=0°20' 2.281,1 3.208,1.167 0.927,0.167 10 false CAS=4°00' 1.75,3.74 1.865,3.896 0.115,0.156 10 false 0 1.458,3.74 1.615,3.896 0.156,0.156 10 false 1 1.167,3.74 1.281,3.885 0.115,0.146 10 false 2 0.875,3.74 0.99,3.896 0.115,0.156 10 false 3 0.615,3.74 0.729,3.906 0.115,0.167 10 false 4 0.458,3.063 0.604,3.219 0.146,0.156 10 false 0 0.448,3.344 0.604,3.5 0.156,0.156 10 false 1 0.469,3.615 0.594,3.76 0.125,0.146 10 false 2 1.958,3.74 2.115,3.896 0.156,0.156 10 false -1 2.271,3.74 2.417,3.885 0.146,0.146 10 false -2 2.573,3.74 2.719,3.896 0.146,0.156 10 false -3 2.865,3.74 3.031,3.906 0.167,0.167 10 false -4 0.448,2.74 0.604,2.896 0.156,0.156 10 false -1 0.448,2.458 0.594,2.604 0.146,0.146 10 false -2 0.448,2.188 0.594,2.344 0.146,0.156 10 false -3 0.438,1.896 0.604,2.063 0.167,0.167 10 false -4 0.438,1.604 0.604,1.771 0.167,0.167 10 false -5 0.438,1.302 0.604,1.469 0.167,0.167 10 false -6

Read the adjustment chart (example).

i.

Find the wheel alignment standard value applicable for the particular model.


ii.

Mark the standard value on the adjustment chart.

Standard Value (Reference):
Camber Caster
0°03' (0.05°) 4°07' (4.12°)



iii.

Mark the alignment value measured when the vehicle is unloaded on the adjustment chart.

Measured Value (Reference):
Camber Caster
0°20' (0.33°) 4°00' (4.00°)



iv.

As shown in the chart, read the distance from the marked point to 0, and adjust the front and/ or rear adjusting cams accordingly.

Amount to Turn Adjusting Cams (by Gradation):
Front Adjusting Cam Rear Adjusting Cam
+1.5 +2.0


C183665E03
1.042,0.854 1.646,1.042 0.604,0.188 10 false Camber 1.042,1.125 1.49,1.313 0.448,0.188 10 false Caster 2.823,8.26 4.24,8.49 1.417,0.229 10 false Rear Cam Graduation 3.344,7.99 3.583,8.208 0.24,0.219 10 false (+) 0.583,5.094 0.823,5.313 0.24,0.219 10 false (+) 3.385,1.469 3.625,1.688 0.24,0.219 10 false (-) 6.792,5.083 7.031,5.302 0.24,0.219 10 false (-) 0.281,4.135 1.073,4.49 0.792,0.354 10 false Front Cam Graduation 2.469,7.229 3.427,7.385 0.958,0.156 10 false CAS=3°40' 3.656,7.24 4.479,7.396 0.823,0.156 10 false CAS=3°00' 4.833,7.24 5.708,7.396 0.875,0.156 10 false CAS=2°20' 0.229,5.625 1.198,5.792 0.969,0.167 10 false CAM=-0°40' 0.229,6.031 1.198,6.198 0.969,0.167 10 false CAM=-0°50' 0.229,6.427 1.198,6.594 0.969,0.167 10 false CAM=-1°00' 5.823,3.292 6.74,3.458 0.917,0.167 10 false CAM=1°00' 5.823,3.719 6.74,3.885 0.917,0.167 10 false CAM=0°50' 5.823,4.125 6.74,4.292 0.917,0.167 10 false CAM=0°40' 5.823,4.51 6.74,4.677 0.917,0.167 10 false CAM=0°30' 5.823,4.865 6.74,5.031 0.917,0.167 10 false CAM=0°20' 5.823,5.281 6.74,5.448 0.917,0.167 10 false CAM=0°10' 5.823,5.656 6.74,5.823 0.917,0.167 10 false CAM=0°00' 5.823,6.01 6.74,6.177 0.917,0.167 10 false CAM=-0°10' 5.823,6.365 6.74,6.531 0.917,0.167 10 false CAM=-0°20' 5.823,6.708 6.74,6.875 0.917,0.167 10 false CAM=-0°30' 0.844,2.281 1.76,2.448 0.917,0.167 10 false CAS=6°00' 2.135,2.281 3.052,2.448 0.917,0.167 10 false CAS=5°20' 3.281,2.281 4.198,2.448 0.917,0.167 10 false CAS=4°40' 4.469,2.281 5.385,2.448 0.917,0.167 10 false CAS=4°00' 3.938,4.927 4.146,5.094 0.208,0.167 10 true -2 4.208,4.927 4.417,5.094 0.208,0.167 10 true -3 4.521,4.927 4.729,5.094 0.208,0.167 10 true -4 4.844,4.927 5.052,5.094 0.208,0.167 10 true -5 5.146,4.927 5.354,5.094 0.208,0.167 10 true -6 5.417,4.927 5.625,5.094 0.208,0.167 10 true -7 3.667,4.927 3.875,5.094 0.208,0.167 10 true -1 3.292,4.198 3.5,4.365 0.208,0.167 10 true -2 3.292,3.906 3.5,4.073 0.208,0.167 10 true -3 3.292,3.604 3.5,3.771 0.208,0.167 10 true -4 3.292,3.313 3.5,3.479 0.208,0.167 10 true -5 3.292,3.021 3.5,3.188 0.208,0.167 10 true -6 3.292,2.729 3.5,2.896 0.208,0.167 10 true -7 3.292,4.479 3.5,4.646 0.208,0.167 10 true -1 3.104,4.938 3.313,5.104 0.208,0.167 10 true 1 2.802,4.938 3.01,5.104 0.208,0.167 10 true 2 2.521,4.938 2.729,5.104 0.208,0.167 10 true 3 1.906,4.938 2.115,5.104 0.208,0.167 10 true 5 2.229,4.938 2.438,5.104 0.208,0.167 10 true 4 1.333,4.938 1.542,5.104 0.208,0.167 10 true 7 1.625,4.938 1.833,5.104 0.208,0.167 10 true 6 3.292,5.094 3.5,5.26 0.208,0.167 10 true 1 3.292,5.385 3.5,5.552 0.208,0.167 10 true 2 3.292,5.688 3.5,5.854 0.208,0.167 10 true 3 3.292,6.25 3.5,6.417 0.208,0.167 10 true 5 3.292,5.948 3.5,6.115 0.208,0.167 10 true 4 3.292,6.875 3.5,7.042 0.208,0.167 10 true 7 3.292,6.542 3.5,6.708 0.208,0.167 10 true 6 3.292,4.76 3.5,4.927 0.208,0.167 10 true 0 3.458,4.927 3.667,5.094 0.208,0.167 10 true 0



Hide 5.INSPECT TOE-IN

A166181E11
1.664,0.297 1.776,0.455 0.112,0.158 10 A 1.637,0.759 1.852,0.918 0.215,0.158 10 *a 1.662,1.956 1.774,2.114 0.112,0.158 10 B

a.

Bounce the vehicle up and down at the corners to stabilize the suspension, and then inspect the toe-in.

Text in Illustration
*a Front of the Vehicle

Standard Toe-in (Unloaded Vehicle):
Vehicle Model Tire Size B - A
USK60L-GKTSKA P275/65R18 8JJ 2.15 mm (0.0847 in.)
P275/55R20 8JJ 2.15 mm (0.0847 in.)
USK60L-GKTLKA P275/65R18 8JJ 2.27 mm (0.0894 in.)
P275/55R20 8JJ 2.27 mm (0.0894 in.)
USK60L-GKTZKA P275/55R20 8JJ 2.36 mm (0.0929 in.)
USK65L-GKTSKA P275/65R18 8JJ 2.31 mm (0.0909 in.)
P275/55R20 8JJ 2.31 mm (0.0909 in.)
USK65L-GKTLKA P275/65R18 8JJ 2.36 mm (0.0929 in.)
P275/55R20 8JJ 2.36 mm (0.0929 in.)
USK65L-GKTZKA P275/55R20 8JJ 2.53 mm (0.0996 in.)
USK65L-GKTSGA P275/65R18 8JJ 2.31 mm (0.0909 in.)
P275/55R20 8JJ 2.31 mm (0.0909 in.)
USK65L-GKTLGA P275/65R18 8JJ 2.36 mm (0.0929 in.)
P275/55R20 8JJ 2.36 mm (0.0929 in.)
USK65L-GKTZGA P275/55R20 8JJ 2.53 mm (0.0996 in.)


If the toe-in is not as specified, adjust it at the rack ends.



Hide 6.ADJUST TOE-IN

a.

Release the rack boot set clips.


b.

Loosen the tie rod end lock nuts.


c.

Turn the right and left rack ends by an equal amount to adjust the toe-in to the center value.


d.
C159783E04
1.375,0.385 1.594,0.552 0.219,0.167 10 true *a 1.125,1.177 1.344,1.344 0.219,0.167 10 true *1

Check that the lengths of the right and left rack ends are approximately the same.

Text in Illustration
*1 Lock Nut
*a Length

Standard difference:

0 +/-1 mm (0 +/-0.0394 in.)



e.

Tighten the tie rod end lock nuts.

Torque:
82 N*m (836 kgf*cm, 61 ft.*lbf)


f.

Attach the clips to the boots.

HINT:

Make sure that the boots are not twisted.



Hide 7.INSPECT WHEEL ANGLE

a.
C132439E14
2.718,0.15 2.901,0.327 0.184,0.176 10 *a 2.383,0.15 2.567,0.327 0.184,0.176 10 *b 0.512,0.15 0.696,0.327 0.184,0.176 10 *a 0.843,0.15 1.027,0.327 0.184,0.176 10 *b 1.634,0.657 1.827,0.834 0.194,0.176 10 *c

Turn the steering wheel to the left and right to the full lock positions and measure the turning angle.

Text in Illustration
*a Inside
*b Outside
*c Front of the Vehicle

Standard Wheel Angle (Unloaded Vehicle):
Vehicle Model Tire Size Inside Wheel Angle Outside Wheel Angle (Reference)
USK60L-GKTSKA P275/65R18 8JJ -40°59' (-40.99°) 36°22' (36.36°)
P275/55R20 8JJ -40°59' (-40.99°) 36°22' (36.36°)
USK60L-GKTLKA P275/65R18 8JJ -41°00' (-41.00°) 36°23' (36.38°)
P275/55R20 8JJ -41°00' (-41.00°) 36°23' (36.38°)
USK60L-GKTZKA P275/55R20 8JJ -41°01' (-41.01°) 36°23' (36.39°)
USK65L-GKTSKA P275/65R18 8JJ -41°17' (-41.28°) 36°24' (36.40°)
P275/55R20 8JJ -41°17' (-41.28°) 36°24' (36.40°)
USK65L-GKTLKA P275/65R18 8JJ -41°17' (-41.28°) 36°25' (36.41°)
P275/55R20 8JJ -41°17' (-41.28°) 36°25' (36.41°)
USK65L-GKTZKA P275/55R20 8JJ -41°17' (-41.29°) 36°26' (36.43°)
USK65L-GKTSGA P275/65R18 8JJ -41°17' (-41.28°) 36°24' (36.40°)
P275/55R20 8JJ -41°17' (-41.28°) 36°24' (36.40°)
USK65L-GKTLGA P275/65R18 8JJ -41°17' (-41.28°) 36°25' (36.41°)
P275/55R20 8JJ -41°17' (-41.28°) 36°25' (36.41°)
USK65L-GKTZGA P275/55R20 8JJ -41°17' (-41.29°) 36°26' (36.43°)



Hide 8.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 9.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 10.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

Hide 11. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION

Hide 12. CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION