Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM
RM27L0U _53 Suspension _049319 TIRE PRESSURE MONITORING _0235729 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  Tire Pressure Warning Light Circuit  


DESCRIPTION

If the tire pressure warning ECU detects a disconnected connector or an open circuit between the tire pressure warning ECU and combination meter, the tire pressure warning light turns off 10 seconds after the ignition switch is turned ON, blinks for 1 minute, and then remains on. Connecting terminals TC and CG of the DLC3 makes the tire pressure warning light blink and outputs the DTC.

WIRING DIAGRAM

C353474E01
5.927,1.833 6.26,2.031 0.333,0.198 10 false IND 0.865,1.844 1.198,2.042 0.333,0.198 10 false TIRE 1.313,1.729 1.469,1.917 0.156,0.188 10 false 7 5.688,1.729 5.844,1.917 0.156,0.188 10 false 5 5.333,2.802 5.667,3 0.333,0.198 10 false H40 0.156,2.844 0.49,3.042 0.333,0.198 10 false H37 0.146,3 1.396,3.208 1.25,0.208 10 false Combination Meter 5.333,2.969 7.094,3.167 1.76,0.198 10 false Tire Pressure Warning ECU

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU, read the transmitter IDs stored in the old ECU using the Techstream and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU after the ECU and/or tire pressure warning valve and transmitter has been replaced.



PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (COMBINATION METER)
a.

Turn the ignition switch off.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON and turn the Techstream on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Check the condition of the tire pressure warning light by operating the Techstream.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Indicat. Tire Pressure Warning System Tire Pressure Warning Light ON or OFF Confirm that the vehicle is stopped with the engine idling

OK:

The warning light turns on when operating the Techstream.




OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECU)

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECU)
a.

Disconnect the H40 ECU connector.


b.

Disconnect the H37 meter connector.


c.
U153449E02
1.979,1.719 2.427,1.75 true 1.51,3.792 1.375,4.271 true 0.333,0.073 2.729,0.583 2.396,0.51 10 false Front view of wire harness connector: (to Tire Pressure Warning ECU) 0.354,2.438 2.75,2.948 2.396,0.51 10 false Front view of wire harness connector: (to Combination Meter) 0.719,1.188 1.01,1.385 0.292,0.198 10 false H40 0.24,3.698 0.531,3.896 0.292,0.198 10 false H37 2.469,1.667 2.938,1.927 0.469,0.26 10 false IND 1.219,4.292 1.594,4.448 0.375,0.156 10 false TIRE

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-5 (IND) - H37-7 (TIRE) Always Below 1 Ω
H40-5 (IND) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR