Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM
RM27L0U _53 Suspension _049319 TIRE PRESSURE MONITORING _0235729 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3. The DTCs are indicated by the blinking of the tire pressure warning light.

WIRING DIAGRAM

E110507E62
5.292,4.104 6.99,4.313 1.698,0.208 10 false Tire Pressure Warning ECU 0.51,3.979 0.917,4.125 0.406,0.146 10 false DLC3 6.146,1.979 6.417,2.198 0.271,0.219 10 false TC 0.896,2 1.167,2.219 0.271,0.219 10 false TC 0.875,3.229 1.146,3.448 0.271,0.219 10 false CG 1.208,1.875 1.417,2.042 0.208,0.167 10 false 13 1.219,3.104 1.344,3.26 0.125,0.156 10 false 4 5.292,3.938 5.573,4.125 0.281,0.188 10 false H40 5.906,1.875 6.052,2.052 0.146,0.177 10 false 3 0.51,3.781 0.802,3.948 0.292,0.167 10 false H19

HINT:

When each warning light continues blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU, read the transmitter IDs stored in the old ECU using the Techstream and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU after the ECU and/or tire pressure warning valve and transmitter has been replaced.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DLC3 - ECU AND BODY GROUND)
a.

Disconnect the H40 ECU connector.


b.
U153424E02
1.667,0.99 0.917,1.688 false 1.823,1.333 2.354,1.719 false 1.688,3.781 2.521,4.198 false 0.125,0.083 1.385,0.292 1.26,0.208 10 false Front view of DLC3: 2.396,1.646 2.625,1.802 0.229,0.156 10 false TC 0.677,1.646 0.927,1.833 0.25,0.188 10 false CG 2.573,4.135 2.823,4.302 0.25,0.167 10 false TC 0.115,2.146 2.469,2.521 2.354,0.375 10 false Front view of wire harness connector: (to Tire Pressure Warning ECU) 0.375,1.104 0.656,1.271 0.281,0.167 10 false H19 0.604,3.583 0.906,3.76 0.302,0.177 10 false H40

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-3 (TC) - H19-13 (TC) Always Below 1 Ω
H40-3 (TC) - Body ground Always 10 kΩ or higher
H19-4 (CG) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR