Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM
RM27L0U _53 Suspension _049319 TIRE PRESSURE MONITORING _0235729 TIRE PRESSURE WARNING SYSTEM D

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  SYSTEM DESCRIPTION  


DESCRIPTION OF SYSTEM


a.

Each tire pressure warning valve and transmitter is equipped with a tire pressure sensor and transmitter and is installed in each tire wheel. The sensor measures the tire pressure. The measured value and transmitter ID are transmitted to the tire pressure warning antenna and receiver on the body as radio waves and then sent to the tire pressure warning ECU from the tire pressure warning antenna and receiver. If the transmitter ID has already been registered, the ECU compares the measured air pressure value with the specified value. When the value is less than the specified value registered in the tire pressure warning ECU, the warning light on the combination meter turns on.

The tire pressure warning reset switch addresses the differences in the standard pressure of the tire.

C159181E03
2.896,2.24 2.896,2.375 2.896,2.375 2.781,2.375 false 2.281,2.125 1.375,2.125 1.375,2.125 1.375,2.573 false 2.083,1.573 1.813,1.031 1.813,1.031 1.604,1.031 false 2.323,1.302 1.969,0.438 1.969,0.438 1.865,0.438 false 2.74,2.719 2.74,3.313 false 4.76,2.719 4.76,3.104 4.76,3.104 2.74,3.104 false 4.188,1.885 5.854,1.885 false 2.74,0.99 2.74,0.167 2.74,0.167 5.125,0.167 false 4.74,0.99 4.74,0.167 false 0.125,2.604 1.969,2.813 1.844,0.208 10 false Combination Meter Assembly 0.135,2.927 1.99,3.156 1.854,0.229 10 false - Tire Pressure Warning Light 5.188,0.094 6.938,0.49 1.75,0.396 10 false Tire Pressure Warning Valve and Transmitter 2.448,3.333 5.208,3.542 2.76,0.208 10 false Tire Pressure Warning Valve and Transmitter 0.198,0.938 1.625,1.281 1.427,0.344 10 false Tire Pressure Warning Reset Switch 0.156,0.365 1.917,0.552 1.76,0.188 10 false Tire Pressure Warning ECU 1.01,1.802 1.406,1.969 0.396,0.167 10 false Front 2.406,2.302 2.802,2.469 0.396,0.167 10 false DLC3 5.906,1.813 6.99,2.354 1.083,0.542 10 false Tire Pressure Warning Antenna and Receiver



INITIAL CHECK


a.
C124985E27
1.792,1.729 1.719,1.802 false 0.167,0.573 0.698,0.771 0.531,0.198 10 false Normal 0.177,1.438 0.906,1.604 0.729,0.167 10 false Malfunction 1.042,0.49 1.229,0.635 0.188,0.146 10 false on 1.042,1.313 1.24,1.458 0.198,0.146 10 false on 1.042,0.781 1.24,0.938 0.198,0.156 10 false off 1.042,1.594 1.24,1.75 0.198,0.156 10 false off 1.958,0.156 2.354,0.302 0.396,0.146 10 false 3 sec. 0.615,1.823 1.875,2.01 1.26,0.188 10 false Ignition Switch ON

After the ignition switch is turned to ON, the tire pressure warning light turns on for 3 seconds and then turns off.

HINT:

If the warning light does not turn on for 3 seconds, troubleshoot the pressure warning light circuit.

Trouble Area Proceed to
Tire pressure warning light circuit (Click here)




WHEN TIRE PRESSURE WARNING LIGHT IS LIT


a.

When the tire pressure warning light does not go off, or when it turns on during driving, check the tire pressure. If the tire pressure warning light turns on within several hours after adjusting the tire pressure, the tire may have a slow air leak.


b.

Under the following conditions, the system may not function properly.

i.

The system will be disabled in the following conditions:

(When the condition becomes normal, the system will work properly.)

·

If tires not equipped with the tire pressure warning valves and transmitters are used.

·

If the ID code on the tire pressure warning valves and transmitters is not registered in the tire pressure warning ECU.

·

If the tire pressure warning valve and transmitter battery voltage drops (battery life: 10 years).



ii.

The system may be disabled in the following conditions:

(When the condition becomes normal, the system will work properly.)

·

If electronic devices or facilities using similar radio wave frequencies are nearby.

·

If a radio set at similar frequencies is in used in the vehicle.

·

If a window tint that affects the radio wave signal is installed.

·

If there is a lot of snow or ice on the vehicle, in particular around the wheels or wheel housings.

·

If non-genuine wheel are used.

·

If tire chains are used.




c.

If a tire pressure warning valve and transmitter is removed from a wheel, replace the grommets.


d.

After removing and installing the ECU or a sensor, check for a DTC and verify that it is a normal code.



FUNCTION OF COMPONENTS


Component Function
Tire pressure warning valve and transmitter Combined as a single unit with a disc wheel air valve, it measures tire pressure and temperature and transmits a transmitter ID for measurement values and identification. Has a built-in battery.
Tire pressure warning antenna and receiver Receives signals from a transmitter and sends the signals to the tire pressure warning ECU.
Tire pressure warning ECU Receives the signal from the receiver and identifies it as the vehicle's own signal. If the measured value is equal to or lower than the specified value, it transmits a signal so that the tire pressure warning light on the combination meter turns on.
Tire pressure warning light Located in the combination meter, it informs the driver of lowered tire pressure and system failure.
Tire pressure warning reset switch Enters the initialization mode for change of the standard pressure.


TIRE PRESSURE WARNING RESET SWITCH


·

By operating the tire pressure warning reset switch, the tire pressure warning ECU can be set to issue a warning at an inflation pressure that corresponds to the standard pressure of tires. Therefore, the dealer must set the warning threshold to the proper value in order to comply with local regulations.

·

Operate the tire pressure warning reset switch only after the inflation pressures of all tires have been adjusted on the vehicle.

·

To initialize the system, press and hold the tire pressure warning reset switch for 3 seconds or longer with the ignition switch ON. When the system receives the initialization signal, the warning light blinks 3 times (1 second on, 1 second off).

·

During initialization, the tire pressure warning valve and transmitter measures the inflation pressure of the tires, and registers the signals that are transmitted into the tire pressure warning ECU at a frequency of once per 3 minutes. The initialization process is completed when signals from all tires have been received. It takes several minutes.