Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM
RM27L0U _53 Suspension _049319 TIRE PRESSURE MONITORING _0235729 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2174/74  Vehicle Speed Signal Malfunction  C2191/91  Vehicle Speed Signal Error (Test Mode DTC)  


DESCRIPTION

Speed signals are input into the tire pressure warning ECU from the combination meter. At the same time, the G-SW in the tire pressure warning valve and transmitter detects driving conditions, and sends signals to the tire pressure warning ECU. If the speed signal from the combination meter stops and the G-SW signal in the tire pressure warning valve and transmitter indicates that the vehicle is being driven, DTC C2174/74 is stored.

DTC C2191/91 is stored only in test mode.

DTC Code DTC Detection Condition Trouble Area
C2174/74 Vehicle speed signal malfunction
·

Combination meter

·

Vehicle speed signal circuit

·

Harness or connector

·

Tire pressure warning ECU

·

Tire pressure warning valve and transmitter


C2191/91 Test mode procedure is performed
·

Meter/gauge system (speed signal)

·

Vehicle speed signal circuit

·

Harness or connector

·

Tire pressure warning ECU



WIRING DIAGRAM

C180357E04
5.094,1.552 5.375,1.74 0.281,0.188 10 false H40 5.229,2.938 5.51,3.125 0.281,0.188 10 false O14 5.083,1.708 6.865,1.906 1.781,0.198 10 false Tire Pressure Warning ECU 5.281,0.573 5.604,0.76 0.323,0.188 10 false SPD 5.281,1.052 5.604,1.24 0.323,0.188 10 false RDA 5.281,2.26 5.604,2.448 0.323,0.188 10 false RDA 5.063,0.49 5.198,0.656 0.135,0.167 10 false 2 5.063,2.167 5.198,2.333 0.135,0.167 10 false 1 5,0.958 5.208,1.135 0.208,0.177 10 false 12 1.448,0.479 1.667,0.667 0.219,0.188 10 false 35 1.448,1.094 1.656,1.26 0.208,0.167 10 false 36 1.188,1.094 1.417,1.281 0.229,0.188 10 false S1 1.177,0.479 1.448,0.646 0.271,0.167 10 false +S 0.208,1.708 0.51,1.938 0.302,0.229 10 false H37 0.208,1.854 1.458,2.052 1.25,0.198 10 false Combination Meter 4.052,2.75 4.969,2.948 0.917,0.198 10 false G-SW Signal 0.875,3.333 1.792,3.531 0.917,0.198 10 false : Radio Signal 2.667,1.198 3.063,1.406 0.396,0.208 10 false SP1 2.615,1.781 2.927,1.948 0.313,0.167 10 false A19 2.604,1.948 3.792,2.146 1.188,0.198 10 false Skid Control ECU 2.458,1.094 2.563,1.25 0.104,0.156 10 false 3 5.24,3.094 6.833,3.448 1.594,0.354 10 false Tire Pressure Warning Antenna and Receiver 2.406,3.052 3.865,3.417 1.458,0.365 10 false Tire Pressure Warning Valve and Transmitter

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU, read the transmitter IDs stored in the old ECU using the Techstream and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU after the ECU and/or tire pressure warning valve and transmitter has been replaced.



HINT:

When the speedometer needle is not moving, first troubleshoot the meter/gauge system (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.READ VALUE USING TECHSTREAM (VEHICLE SPEED)
a.

Turn the ignition switch off.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON and turn the Techstream on.


d.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


e.

Check that the values indicated on the Techstream and on the combination meter are the same.

Tire Pressure Monitor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed reading/
min.: 0 km/h (0 mph)
max.: 255 km/h (158 mph)
Actual vehicle speed The speed indicated on the combination meter

OK:

Vehicle speed indicated on the Techstream indicates the actual speed.




OK

2.CHECK DTC

NG

3.CHECK HARNESS AND CONNECTOR (ECU - COMBINATION METER)
2.CHECK DTC
a.

Perform a driving test.


b.

Check for DTCs.

HINT:

The time required for DTC C2174/74 to be stored is 20 minutes.


Result
Result Proceed to
DTC C2174/74 is not output A
DTC C2174/74 is output B



A

B

6.REPLACE TIRE PRESSURE WARNING ECU
3.CHECK HARNESS AND CONNECTOR (ECU - COMBINATION METER)
a.

Disconnect the H40 tire pressure warning ECU connector.


b.
U153448E02
1.438,1.667 0.969,1.698 true 2.417,3.938 2.417,4.271 true 0.333,0.094 2.729,0.604 2.396,0.51 10 false Front view of wire harness connector: (to Tire Pressure Warning ECU) 0.354,2.5 2.75,3.01 2.396,0.51 10 false Front view of wire harness connector: (to Combination Meter) 0.719,1.188 1.01,1.333 0.292,0.146 10 false H40 0.24,3.698 0.521,3.844 0.281,0.146 10 false H37 0.656,1.625 0.979,1.813 0.323,0.188 10 false SPD 2.323,4.271 2.625,4.438 0.302,0.167 10 false +S

Disconnect the H37 meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-2 (SPD) - H37-35 (+S) Always Below 1 Ω
H40-2 (SPD) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - SKID CONTROL ECU)
U153705E02
2.792,1.302 2.708,2.052 2.708,2.052 2.813,2.052 true 6.042,1.635 6.042,2.115 6.042,2.115 6.156,2.115 true 0.25,0.083 2.583,0.427 2.333,0.344 10 false Front view of wire harness connector: (to Skid Control ECU) 4,0.094 6.333,0.406 2.333,0.313 10 false Front view of wire harness connector: (to Combination Meter) 2.021,0.833 2.292,0.979 0.271,0.146 10 false A19 5.406,0.896 5.698,1.042 0.292,0.146 10 false H37 2.865,1.969 3.208,2.156 0.344,0.188 10 false SP1 6.198,2.031 6.417,2.177 0.219,0.146 10 false S1

a.

Disconnect the A19 skid control ECU connector.


b.

Disconnect the H37 meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A19-3 (SP1) - H37-36 (SI) Always Below 1 Ω
A19-3 (SP1) - Body ground Always 10 kΩ or higher




OK

5.CHECK DTC (SFI SYSTEM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK DTC (SFI SYSTEM)
a.

Check for DTCs.

HINT:


Result
Result Proceed to
DTC P0500 is not output A
DTC P0500 is output B



A

6.REPLACE TIRE PRESSURE WARNING ECU

B

6.REPLACE TIRE PRESSURE WARNING ECU
a.

Replace the tire pressure warning ECU (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING ECU>REMOVAL).



NEXT

7.PERFORM REGISTRATION OF TRANSMITTER ID
7.PERFORM REGISTRATION OF TRANSMITTER ID

NEXT

8.PERFORM INITIALIZATION
8.PERFORM INITIALIZATION

NEXT

9.CHECK DTC
9.CHECK DTC
a.

Perform a driving test.


b.

Check for DTCs.

HINT:

The time required for DTC C2174/74 to be stored is 20 minutes.


Result
Result Proceed to
DTC C2174/74 is output A
DTC C2174/74 is not output B



A

REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER

B

END