Home › Brake › PARKING BRAKE › PARKING BRAKE ASSEMBLY
RM27L0U _54 Brake _049325 PARKING BRAKE _0235757 PARKING BRAKE ASSEMBLY A

PARKING BRAKE  PARKING BRAKE ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL PARKING BRAKE ANCHOR BLOCK

a.
C155126

Install the anchor block with the 2 nuts.

Torque:
86 N*m (877 kgf*cm, 63 ft.*lbf)


Hide 46430 2.CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.
C154244

Connect the No. 3 parking brake cable with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 3.INSTALL PARKING BRAKE SHOE LEVER LH

U153433E02
0.656,1.844 2.51,2.177 1.854,0.333 10 true High temperature grease

a.

Apply high temperature grease to the parking brake shoe lever.


b.
C117760E03
0.397,0.022 0.949,0.260 0.552,0.239 10 for LH: 2.036,0.012 2.583,0.258 0.547,0.246 10 for RH:

Install the parking brake shoe lever to the No. 3 parking brake cable.

NOTICE:

Carefully distinguish the parking brake shoe lever RH and LH.



Hide 46590 4.INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH

a.

Apply high temperature grease to the areas of the backing plate that contact the shoe.


b.
C154249E01
0.76,1.602 0.76,1.871 false 0.588,1.896 0.884,2.053 0.296,0.156 10 SST 0.759,1.607 2.039,1.607 false

Using SST, install the No. 2 parking brake shoe with the shoe hold down spring pin, compression spring and shoe hold down spring cup.

SST
09718-00011  


Hide 46580 5.INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH

a.

Apply high temperature grease to the areas of the backing plate that contact the shoe.


b.
C193371E01
0.764,4.125 2.344,4.299 1.579,0.173 10 High temperature grease

Apply high temperature grease to the areas of the shoe adjuster screw set shown in the illustration.


c.

Set the parking brake shoe and shoe adjuster screw set in place.


d.

Connect the tension spring.


e.
C155124E01
2.796,1.277 2.796,1.546 false 2.624,1.571 2.920,1.728 0.296,0.156 10 SST

Using SST, install the No. 1 parking brake shoe with the shoe hold down spring pin, compression spring and shoe hold down spring cup.

SST
09718-00011  


Hide 6.INSTALL PARKING BRAKE SHOE RETURN SPRING

a.
C191839E01
0.358,1.312 0.664,1.474 0.306,0.163 10 SST 1.017,1.624 1.017,1.388 1.017,1.388 0.72,1.388 false

Using SST, install the shoe return spring.

SST
09703-30011  


Hide 7.CHECK PARKING BRAKE INSTALLATION

a.

Check that each part is installed properly.

C156989E02
0.254,0.189 1.028,0.440 0.774,0.251 10 for LH: 3.636,0.2 4.322,0.452 0.686,0.251 10 for RH: 5.671,2.51 6.054,2.664 0.384,0.154 10 Front 1.302,2.487 1.685,2.640 0.384,0.154 10 Front


Hide 42431 8.INSTALL REAR DISC

Hide 9.CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH

a.
C158344

Connect the rear disc brake cylinder with 2 new bolts.

Torque:
160 N*m (1632 kgf*cm, 118 ft.*lbf)

NOTICE:
·

Do not twist the brake hose.

·

Make sure that the bolts are free from damage and foreign matter.

·

Do not overtighten the bolts.




Hide 10.ADJUST PARKING BRAKE SHOE CLEARANCE

Hide 11.CHECK PARKING BRAKE PEDAL TRAVEL

Hide 12.ADJUST PARKING BRAKE PEDAL TRAVEL

Hide 13.INSTALL REAR WHEEL LH

Torque:
for Aluminum Wheel : 131 N*m (1336 kgf*cm, 97 ft.*lbf)
for Steel Wheel : 209 N*m (2131 kgf*cm, 154 ft.*lbf)

Hide 14.SETTLE PARKING BRAKE SHOE AND DISC

a.

Drive the vehicle for approximately 400 m (0.25 miles) under the following conditions.

i.

The vehicle speed is approximately 50 km/h (31 mph) and the vehicle is on a safe, level and dry road.


ii.

The parking brake pedal is being depressed with a force of 150 N (15 kgf, 33.7 lbf).



b.

Repeat the procedures above 2 or 3 times.