Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
RM27L0U _55 Steering _049327 STEERING COLUMN _0235762 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM U

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  TERMINALS OF ECU  


CHECK MULTIPLEX TILT AND TELESCOPIC ECU


U154202E02
1.51,0.125 2.552,0.333 1.042,0.208 10 false Connector A: 4.792,0.104 5.083,0.302 0.292,0.198 10 false H57

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-2 (TEM+) - H57-11 (GND) (Not available) - W-B Telescopic motor output
·

Ignition switch ON

·

Telescopic steering contracts


11 to 14 V
Telescopic motor is not operating Below 1 V
A-3 (VCE) - A-5 (E2) (Not available) Telescopic sensor power source Ignition switch ON 8 to 16 V
A-4 (TES) - A-5 (E2) (Not available) Telescopic sensor signal Telescopic motor is operating Pulse generation
HI: 8 to 16 V
LOW: 0 V
A-5 (E2) - Body ground (Not available) - Body ground Telescopic sensor ground Always Below 1 V
A-6 (TEM-) - H57-11 (GND) (Not available) - W-B Telescopic motor output
·

Ignition switch ON

·

Telescopic steering extends


11 to 14 V
Telescopic motor is not operating Below 1 V
H57-1 (TIM-) - H57-11 (GND) R - W-B Tilt motor output
·

Ignition switch ON

·

Steering tilts down


11 to 14 V
Tilt motor is not operating Below 1 V
H57-2 (+B) - H57-11 (GND) V - W-B Motor power source Always 11 to 14 V
H57-3 (MSW) - H57-11 (GND) GR - W-B Manual switch signal
·

Ignition switch ON

·

Tilt up by manual switch


1.67 to 2.13 V
·

Ignition switch ON

·

Tilt down by manual switch


0.54 to 0.74 V
·

Ignition switch ON

·

Telescopic contracted by manual switch


1.08 to 1.40 V
·

Ignition switch ON

·

Telescopic extended by manual switch


2.22 to 2.77 V
Manual switch is not operating Below 0.2 V
H57-4 (VC) - H57-11 (GND) Y - W-B Manual switch power source Ignition switch ON 4.9 to 5.1 V
H57-5 (CANH) - H57-11 (GND) BE - W-B CAN communication Ignition switch ON Pulse generation
H57-6 (VCI) - H57-17 (E1) SB - LG Tilt sensor power source Ignition switch ON 8 to 16 V
H57-7 (TIS) - H57-17 (E1) G - LG Tilt sensor signal Tilt motor is operating Pulse generation
HI: 8 to 16 V
LOW: 0 V
H57-8 (IG) - H57-11 (GND) P - W-B IG signal/IG power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
H57-9 (ECUB) - H57-11 (GND) L - W-B ECU power source Always 11 to 14 V
H57-10 (TIM+) - H57-11 (GND) B - W-B Tilt motor output
·

Ignition switch ON

·

Steering tilts up


11 to 14 V
Tilt motor is not operating Below 1 V
H57-11 (GND) - Body ground W-B - Body ground ECU ground Always Below 1 V
H57-14 (CANL) - H57-11 (GND) W - W-B CAN communication Ignition switch ON Pulse generation
H57-17 (E1) - Body ground LG - Body ground Tilt sensor ground Always Below 1 V