Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
RM27L0U _55 Steering _049327 STEERING COLUMN _0235762 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM U

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical/ Tilt & Telescopic / Data List.


e.

Check the values by referring to the table below.

Tilt & Telescopic
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Tilt Position Current tilt position data / min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)
-
Telesco Position Current telescopic position data / min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)
-
Tilt Return Position Memorized tilt return position data / min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)
-
Telesco Return Position Memorized telescopic return position data / min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)
-
Tilt Memory Pos 1 Tilt data of memory position 1 / min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)
-
Telesco Memory Pos 1 Telescopic data of memory position 1 / min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)
-
Tilt Memory Pos 2 Tilt data of memory position 2 / min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)
-
Telesco Memory Pos 2 Telescopic data of memory position 2 / min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)
-
Tilt Up Limit Uppermost tilt position / Not Mem or Mem Not Mem: Position is not memorized
Mem: Position is memorized
-
Tilt Up Limit Position Uppermost tilt position data / min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)
-
Tilt Down Limit Lowermost tilt position / Not Mem or Mem Not Mem: Position is not memorized
Mem: Position is memorized
-
Tilt Down Limit Position Lowermost tilt position data / min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)
-
Telesco Short Limit Shortest telescopic position / Not Mem or Mem Not Mem: Position is not memorized
Mem: Position is memorized
-
Telesco Short Limit Pos Shortest telescopic position data / min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)
-
Telesco Long Limit Longest telescopic position / Not Mem or Mem Not Mem: Position is not memorized
Mem: Position is memorized
-
Telesco Long Limit Pos Longest telescopic position data / min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)
-
Tilt Up Switch Input state of tilt up by manual switch / ON or OFF ON: Tilt up is activated by manual switch
OFF: Tilt up is not activated by manual switch
-
Tilt Up SW(CAN) Communication state of tilt up input by manual switch / ON or OFF ON: Tilt up is activated by manual switch
OFF: Tilt up is not activated by manual switch
-
Tilt Down Switch Input state of tilt down by manual switch / ON or OFF ON: Tilt down is activated by manual switch
OFF: Tilt down is not activated by manual switch
-
Tilt Down SW(CAN) Communication state of tilt down input by manual switch / ON or OFF ON: Tilt down is activated by manual switch
OFF: Tilt down is not activated by manual switch
-
Telesco Short Switch Input state of telescopic short by manual switch / ON or OFF ON: Telescopic short is activated by manual switch
OFF: Telescopic short is not activated by manual switch
-
Telesco Short SW(CAN) Communication state of telescopic short input by manual switch / ON or OFF ON: Telescopic short is activated by manual switch
OFF: Telescopic short is not activated by manual switch
-
Telesco Long Switch Input state of telescopic long by manual switch / ON or OFF ON: Telescopic long is activated by manual switch
OFF: Telescopic long is not activated by manual switch
-
Telesco Long SW(CAN) Communication state of telescopic long input by manual switch / ON or OFF ON: Telescopic long is activated by manual switch
OFF: Telescopic long is not activated by manual switch
-
T&T Manual SW Data Voltage data of manual switch / min.: 0.00 V, max.: 4.99 V Neutral position: Below 0.2 V
Tilt up: 1.67 to 2.13 V
Tilt down: 0.54 to 0.74 V
Telescopic contract: 1.08 to 1.40 V
Telescopic extend: 2.22 to 2.77 V
-
S/B Mem1 Tilt and telescopic memory position 1 / Not Mem or Mem Not Mem: Position is not memorized
Mem: Position is memorized
-
S/B Mem2 Tilt and telescopic memory position 2 / Not Mem or Mem Not Mem: Position is not memorized
Mem: Position is memorized
-
S/B Mem3 Tilt and telescopic memory position 3 / Not Mem or Mem Not Mem: Position is not memorized
Mem: Position is memorized
-
T&T Autoaway Function Auto away/return function / ON or OFF ON: Auto away/return function is allowed
OFF: Auto away/return function is prohibited
-
Power Source Voltage Voltage data of power supply / min.: 0.00 V, max.: 19.99 V Actual power supply voltage
11 to 14 V
-
Freeze Speed Info Vehicle speed data / min: 0 km/h (0 mph), max.: 255 km/h (158 mph) Actual vehicle speed -
IG Switch (CAN) Communication state of ignition switch / ON or OFF ON: Communication is normal
OFF: Communication is interrupted
-
IG Switch Input state of ignition switch / ON or OFF ON: Input signal is normal
OFF: Input signal is interrupted
-
Key Switch(CAN) Communication state of unlock warning switch signal / ON or OFF ON: Communication is normal
OFF: Communication is interrupted
-
Key Switch Input state of unlock warning switch / ON or OFF ON: Communication is normal
OFF: Communication is interrupted
-
Key Code Confirm(CAN) Communication state of key code confirmation signal / ON or OFF ON: Communication is normal
OFF: Communication is interrupted
-
Receive from Meter Communication state of combination meter signal / OK or Interpt OK: Communication is normal
Interpt: Communication is interrupted
-
Receive from Seat ECU Communication state of front power seat control switch LH signal / OK or Interpt OK: Communication is normal
Interpt: Communication is interrupted
-
Receive from Combi Communication state of combination switch ECU signal / OK or Interpt OK: Communication is normal
Interpt: Communication is interrupted
-
J/B Communication state of main body ECU signal / OK or Interpt OK: Communication is normal
Interpt: Communication is interrupted
-
B/B Communication state of optional after parts ECU signal / OK or Interpt OK: Communication is normal
Interpt: Communication is interrupted
-
The Number of DTCs Number of diagnostic trouble codes / min.: 0, max.: 255 Actual number of diagnostic trouble codes -



PERFORM ACTIVE TEST


HINT:

Using the Techstream to perform the Active Tests allows relays, VSVs and actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Tilt & Telescopic / Active Test.


e.

Check the values by referring to the table below.

Tilt & Telescopic
Tester Display Test Part Control Range Diagnostic Note
Tilt Operation Tilt operation Up / Down -
Telesco Operation Telescopic operation Long / Short -