Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR
RM27L0U _55 Steering _049328 STEERING GEAR / LINKAGE _0235768 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  DISASSEMBLY  


PROCEDURE

Hide 44250 1.FIX POWER STEERING GEAR ASSEMBLY

C159512E02
2.51,0.802 2.51,0.354 2.51,0.354 2.646,0.354 false 2.229,1.229 1.458,1.229 false 2.719,0.271 3.083,0.458 0.365,0.188 10 false SST 0.76,1.146 1.51,1.344 0.75,0.198 10 false Vinyl Tape

a.

Using SST, secure the power steering gear.

SST
09612-00012  

HINT:

Tape SST before use.


NOTICE:

When using a vise, do not overtighten it.



Hide 45047 2.REMOVE TIE ROD END SUB-ASSEMBLY LH

C154516E01
1.739,0.107 2.493,0.266 0.754,0.159 10 Matchmark 0.906,0.642 0.906,0.203 false 0.906,0.203 1.709,0.203 false 1.127,0.777 1.127,0.203 false

a.

Put matchmarks on the tie rod end LH and steering rack end.


Hide 45046 3.REMOVE TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 4.REMOVE STEERING RACK BOOT CLIP

a.

Using pliers, remove the 2 steering rack boot clips.


Hide 5.REMOVE NO. 2 STEERING RACK BOOT CLAMP

C159523

a.

Using pliers, remove the 2 boot clamps as shown in the illustration.

NOTICE:

Be careful not to damage the No. 2 steering rack boot.



Hide 45536 6.REMOVE NO. 2 STEERING RACK BOOT

Hide 45535 7.REMOVE NO. 1 STEERING RACK BOOT

Hide 45503 8.REMOVE STEERING RACK END SUB-ASSEMBLY

ZX09339

a.

Using a screwdriver and hammer, stake back the washer.

NOTICE:

Do not strike the steering rack.



b.

Using a wrench, hold the steering rack (LH side).


c.
C353500E01
0.813,0.552 1.073,0.688 false 0.469,3.417 0.729,3.354 false 2.771,3.896 2.5,3.75 false 1.771,1.865 2.063,2.354 false 0.135,0.063 0.448,0.26 0.313,0.198 10 false LH 0.125,2.375 0.438,2.573 0.313,0.198 10 false RH 0.521,0.458 0.969,0.656 0.448,0.198 10 false SST 1.844,0.344 2.292,0.542 0.448,0.198 10 false Turn 1.552,2.927 2,3.125 0.448,0.198 10 false Turn 0.156,3.323 0.604,3.521 0.448,0.198 10 false SST 2.844,3.823 3.292,4.021 0.448,0.198 10 false SST 1.833,2.354 2.75,2.552 0.917,0.198 10 false Wrench 0.969,4.406 1.417,4.604 0.448,0.198 10 false Hold

Using SST, remove the steering rack end (LH side) from the power steering rack.

SST
09922-10010  

NOTICE:

Rotate SST in the direction shown in the illustration.



d.

Using SST, remove the steering rack end (RH side) from the power steering rack.

SST
09922-10010  

NOTICE:

Rotate SST in the direction shown in the illustration.



e.

Remove the 2 claw washers.


Hide 9.REMOVE STEERING GEAR RACK GUIDE

C206204

a.

Using SST, remove the steering rack guide spring cap nut.

SST
09922-10010  

NOTICE:

Rotate SST in the direction shown in the illustration.



b.
C206205

Using a 32 mm hexagon wrench, remove the rack guide spring cap.


c.

Remove the spring and rack guide.


Hide 10.REMOVE POWER STEERING CONTROL VALVE

a.
F051708E02
0.802,0.375 1.177,0.125 false 1.208,0.021 1.885,0.198 0.677,0.177 10 false Vinyl Tape

Wind vinyl tape around the serrated portion of the control valve.


b.

Remove the dust cover from the control valve housing.


c.
G100343

Remove the 2 bolts.


d.

Pull out the control valve from the rack housing.


e.

Remove the control valve oil seal.


f.
F051710E02
1.844,0.896 2.063,0.677 false 2.104,0.552 2.781,0.729 0.677,0.177 10 false Vinyl Tape

To prevent the oil seal lip from getting damaged, wind vinyl tape around the serrated portion of the control valve.


g.

Using a plastic hammer, remove the control valve from the control valve housing.


h.
F051711E02
1.135,0.969 0.885,1.438 0.885,1.438 1.438,1.281 false 1.219,1.063 0.906,1.406 false 1.323,1.156 0.896,1.427 false 0.198,1.458 1.438,1.635 1.24,0.177 10 false Control Valve Rings

Using a screwdriver, remove the 4 control valve rings.

NOTICE:

Be careful not to damage the grooves for the control valve rings.



Hide 11.REMOVE POWER STEERING CONTROL VALVE UPPER OIL SEAL

C206224E01
0.134,0.679 0.458,0.853 0.325,0.174 10 SST 0.515,0.776 0.873,1.126 false 0.515,0.776 0.924,0.725 false

a.

Using SST and a press, remove the control valve upper bearing and control valve upper oil seal from the control valve housing.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07150)


Hide 12.REMOVE CYLINDER END STOPPER

C353501

a.

Using a screwdriver and hammer, turn the cylinder end stopper clockwise until the wire end can be seen through the service hole.


b.

Using a screwdriver and hammer, turn the cylinder end stopper counterclockwise, and remove the wire and cylinder end stopper.


Hide 13.REMOVE POWER STEERING RACK

Hide 14.REMOVE POWER STEERING RACK BUSH

a.

Remove the rack bush from the power steering rack.


b.

Using a screwdriver, remove the O-ring from the rack bush.


c.
F051714E02
1.135,0.75 0.833,0.646 0.833,0.646 0.875,1.354 false 0.479,0.542 0.771,0.719 0.292,0.177 10 false SST

Using SST, remove the rack bush oil seal.

SST
09527-21011  
09612-24014  (09613-22011)


Hide 15.REMOVE POWER STEERING CYLINDER TUBE OIL SEAL

F051715E02
1.344,0.635 1.927,0.271 1.927,0.271 1.417,0.948 false 1.99,0.156 2.281,0.333 0.292,0.177 10 false SST

a.

Using SST and a press, remove the cylinder tube oil seal.

SST
09950-60010  (09951-00320)
09950-70010  (09951-07360)


Hide 16.REMOVE RACK STEERING PISTON RING

R010955

a.

Using a screwdriver, remove the piston ring and O-ring.

NOTICE:

Be careful not to damage the groove for the piston ring.