Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR SEAT ENTERTAINMENT SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049329 AUDIO / VIDEO _0235769 REAR SEAT ENTERTAINMENT SYSTEM J

AUDIO / VIDEO  REAR SEAT ENTERTAINMENT SYSTEM  Mute Signal Circuit between Radio Receiver and Television Display Assembly  


DESCRIPTION

This circuit sends a signal to the television display assembly to mute noise. Because of that, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the television display assembly is normal, no sound, or only an extremely small sound, can be produced.

WIRING DIAGRAM

E345041E01
0.646,1.563 1.104,1.76 0.458,0.198 10 false U13 0.646,1.74 2.563,1.969 1.917,0.229 10 false Television Display Assembly 1.542,0.917 1.948,1.135 0.406,0.219 10 false MUT1 2.01,0.802 2.24,0.99 0.229,0.188 10 false 6 5.052,0.802 5.208,0.99 0.156,0.188 10 false 8 5.24,0.906 5.781,1.135 0.542,0.229 10 false MUTE 5.063,1.531 5.521,1.729 0.458,0.198 10 false I57 5.063,1.708 6.271,2.177 1.208,0.469 10 false Radio and Display Receiver Assembly

PROCEDURE

1.CHECK MUTE SIGNAL CIRCUIT
a.
U154142E02
1.896,0.885 2.135,0.135 true 2.188,0.042 2.708,0.219 0.521,0.177 10 false MUT1 0.094,0 0.313,0.177 0.219,0.177 10 false *a 0.229,0.938 0.615,1.115 0.385,0.177 10 false U13

Remove the television display assembly connector still connected (See page Audio / Visual / Telematics>AUDIO / VIDEO>TELEVISION DISPLAY>REMOVAL).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
U13-6 (MUT1) - Body ground Television display playing Above 3.5 V
Television display changing modes Below 1 V


Text in Illustration
*a Component with harness connected
(Television Display Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
a.

Disconnect the I57 radio and display receiver assembly connector.


b.

Disconnect the U13 television display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I57-8 (MUTE) - U13-6 (MUT1) Always Below 1 Ω
I57-8 (MUTE) - Body ground Always 10 kΩ or higher




OK

3.CHECK TELEVISION DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TELEVISION DISPLAY ASSEMBLY
a.

Temporarily replace the television display assembly with a new or known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>TELEVISION DISPLAY>REMOVAL).


b.

Check that the mute signal circuit functioning normally.

OK:

The mute signal circuit functioning normally.




OK

END (TELEVISION DISPLAY ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY